Launched in 2004, dmesgd aims to provide a user-submitted repository of searchable *BSD dmesgs. The dmesg(8) command displays the system message buffer's content, and during boot a copy is saved to /var/run/dmesg.boot. This buffer contains the operating system release, name and version, a list of devices identified, plus a whole host of other useful information. We hope others find this resource useful and further contribute to its growth. Contact us at [ admin at lists dot nycbug dot org ]. Note that this site is not a substitute for sending the dmesg directly to the respective project.
Date: 2004-06-28 09:18:10
From: th
Description: Home BSD box. 2x AMD MP
Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.9-STABLE #8: Sun Mar 21 22:11:41 EET 2004
harkonen@beastie:/work/obj/usr/src/sys/K7
Timecounter "i8254" frequency 1193182 Hz
CPU: AMD Athlon(tm) MP 2200+ (1800.07-MHz 686-class CPU)
Origin = "AuthenticAMD" Id = 0x680 Stepping = 0
Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
AMD Features=0xc0480000<MP,AMIE,DSP,3DNow!>
real memory = 2146959360 (2096640K bytes)
avail memory = 2084986880 (2036120K bytes)
Programming 24 pins in IOAPIC #0
IOAPIC #0 intpin 2 -> irq 0
FreeBSD/SMP: Multiprocessor motherboard: 2 CPUs
cpu0 (BSP): apic id: 1, version: 0x00040010, at 0xfee00000
cpu1 (AP): apic id: 0, version: 0x00040010, at 0xfee00000
io0 (APIC): apic id: 2, version: 0x00170011, at 0xfec00000
Preloaded elf kernel "kernel" at 0xc03c4000.
Pentium Pro MTRR support enabled
md0: Malloc disk
Using $PIR table, 268435454 entries at 0xc00fdef0
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
IOAPIC #0 intpin 16 -> irq 2
pci0: <PCI bus> on pcib0
pcib1: <PCI to PCI bridge (vendor=1022 device=700d)> at device 1.0 on pci0
IOAPIC #0 intpin 18 -> irq 5
pci1: <PCI bus> on pcib1
pci1: <Matrox MGA G400 AGP graphics accelerator> at 5.0 irq 5
isab0: <PCI to ISA bridge (vendor=1022 device=7440)> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <AMD 768 ATA100 controller> port 0xf000-0xf00f at device 7.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
chip1: <PCI to Other bridge (vendor=1022 device=7443)> at device 7.3 on pci0
pci0: <unknown card> (vendor=0x8086, dev=0x100e) at 8.0 irq 2
pcib2: <PCI to PCI bridge (vendor=1022 device=7448)> at device 16.0 on pci0
IOAPIC #0 intpin 19 -> irq 7
IOAPIC #0 intpin 17 -> irq 10
pci2: <PCI bus> on pcib2
pci2: <OHCI USB controller> at 0.0 irq 7
atapci1: <HighPoint HPT370 ATA100 controller> port 0x2000-0x20ff,0x2c00-0x2c03,0x2c08-0x2c0f,0x2c04-0x2c07,0x2c10-0x2c17 irq 2 at device 4.0 on pci2
ata2: at 0x2c10 on atapci1
ata3: at 0x2c08 on atapci1
sym0: <875> port 0x2400-0x24ff mem 0xf5001000-0xf5001fff,0xf5002000-0xf50020ff irq 10 at device 5.0 on pci2
sym0: Symbios NVRAM, ID 7, Fast-20, SE, parity checking
sym0: open drain IRQ line driver, using on-chip SRAM
sym0: using LOAD/STORE-based firmware.
xl0: <3Com 3c905C-TX Fast Etherlink XL> port 0x2800-0x287f mem 0xf5002400-0xf500247f irq 5 at device 6.0 on pci2
xl0: Ethernet address: [_MAC_XXXXXXXXXX]
miibus0: <MII bus> on xl0
xlphy0: <3c905C 10/100 internal PHY> on miibus0
xlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
xl1: <3Com 3c905C-TX Fast Etherlink XL> port 0x2880-0x28ff mem 0xf5002800-0xf500287f irq 7 at device 8.0 on pci2
xl1: Ethernet address: [_MAC_XXXXXXXXXX]
miibus1: <MII bus> on xl1
ukphy0: <Generic IEEE 802.3u media interface> on miibus1
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
orm0: <Option ROMs> at iomem 0xc0000-0xc7fff,0xc8000-0xc87ff,0xc8800-0xc9fff,0xca000-0xcd7ff,0xcd800-0xcdfff,0xe0000-0xe3fff on isa0
pmtimer0 on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
APIC_IO: Testing 8254 interrupt delivery
APIC_IO: routing 8254 via IOAPIC #0 intpin 2
IPsec: Initialized Security Association Processing.
IP Filter: v3.4.31 initialized. Default = block all, Logging = enabled
SMP: AP CPU #1 Launched!
ad0: timeout waiting for interrupt
ad0: 117800MB <IC35L120AVVA07-0> [239340/16/63] at ata0-master UDMA100
ad1: 114473MB <ST3120023A> [232581/16/63] at ata0-slave UDMA100
ad2: 114473MB <ST3120023A> [232581/16/63] at ata1-master UDMA100
ar0: 58644MB <ATA RAID1 array> [7476/255/63] status: READY subdisks:
0 READY ad4: 58644MB <Maxtor 6Y060L0> [119150/16/63] at ata2-master UDMA100
1 READY ad6: 58644MB <Maxtor 6Y060L0> [119150/16/63] at ata3-master UDMA100
Waiting 10 seconds for SCSI devices to settle
(noperiph:sym0:0:-1:-1): SCSI BUS reset delivered.
Mounting root from ufs:/dev/da0s1a
da2 at sym0 bus 0 target 8 lun 0
da2: <QUANTUM ATLAS10K3_18_SCA 020W> Fixed Direct Access SCSI-3 device
da2: 40.000MB/s transfers (20.000MHz, offset 16, 16bit), Tagged Queueing Enabled
da2: 17537MB (35916548 512 byte sectors: 255H 63S/T 2235C)
da0 at sym0 bus 0 target 1 lun 0
da0: <COMPAQ DGHS09Y 01A0> Fixed Direct Access SCSI-3 device
da0: 40.000MB/s transfers (20.000MHz, offset 15, 16bit), Tagged Queueing Enabled
da0: 8678MB (17773500 512 byte sectors: 255H 63S/T 1106C)
da1 at sym0 bus 0 target 2 lun 0
da1: <COMPAQ DGHS18Y 01C0> Fixed Direct Access SCSI-3 device
da1: 40.000MB/s transfers (20.000MHz, offset 15, 16bit), Tagged Queueing Enabled
da1: 17366MB (35566000 512 byte sectors: 255H 63S/T 2213C)