Launched in 2004, dmesgd aims to provide a user-submitted repository of searchable *BSD dmesgs. The dmesg(8) command displays the system message buffer's content, and during boot a copy is saved to /var/run/dmesg.boot. This buffer contains the operating system release, name and version, a list of devices identified, plus a whole host of other useful information. We hope others find this resource useful and further contribute to its growth. Contact us at [ admin at lists dot nycbug dot org ]. Note that this site is not a substitute for sending the dmesg directly to the respective project.
Date: 2008-08-21 07:13:53
From: ike
Description: Soekris 4801, NanoBSD (FreeBSD embedded install Scripts)
Copyright (c) 1992-2008 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 7.0-RELEASE-p2 #0: Tue Aug 19 23:21:54 EDT 2008 [_EMAIL_XXXXXXXX]:/usr/obj/nanobsd.ike2/usr/src/sys/ike1.kcfg Timecounter i8254 frequency 1193182 Hz quality 0 CPU: Geode(TM) Integrated Processor by National Semi (266.63-MHz 586-class CPU) Origin = Geode by NSC Id = 0x540 Stepping = 0 Features=0x808131<FPU,TSC,MSR,CX8,CMOV,MMX> real memory = 134217728 (128 MB) avail memory = 117444608 (112 MB) kbd1 at kbdmux0 ath_hal:[_IP_XXX] (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413) hptrr: HPT RocketRAID controller driver v1.1 (Aug 19 2008 23:20:57) cpu0 on motherboard pcib0: <Host to PCI bridge> pcibus 0 on motherboard pci0: <PCI bus> on pcib0 sis0: <NatSemi DP8381[56] 10/100BaseTX> port 0xe100-0xe1ff mem 0xa0000000-0xa000 0fff irq 10 at device 6.0 on pci0 sis0: Silicon Revision: DP83816A miibus0: <MII bus> on sis0 ukphy0: <Generic IEEE 802.3u media interface> PHY 0 on miibus0 ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto sis0: Ethernet address: [_MAC_XXXXXXXXXX] sis0: [ITHREAD] sis1: <NatSemi DP8381[56] 10/100BaseTX> port 0xe200-0xe2ff mem 0xa0001000-0xa000 1fff irq 10 at device 7.0 on pci0 sis1: Silicon Revision: DP83816A miibus1: <MII bus> on sis1 ukphy1: <Generic IEEE 802.3u media interface> PHY 0 on miibus1 ukphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto sis1: Ethernet address: [_MAC_XXXXXXXXXX] sis1: [ITHREAD] sis2: <NatSemi DP8381[56] 10/100BaseTX> port 0xe300-0xe3ff mem 0xa0002000-0xa000 2fff irq 10 at device 8.0 on pci0 sis2: Silicon Revision: DP83816A miibus2: <MII bus> on sis2 ukphy2: <Generic IEEE 802.3u media interface> PHY 0 on miibus2 ukphy2: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto sis2: Ethernet address: [_MAC_XXXXXXXXXX] sis2: [ITHREAD] isab0: <PCI-ISA bridge> port 0x6100-0x613f,0x6200-0x623f at device 18.0 on pci0 isa0: <ISA bus> on isab0 pci0: <bridge> at device 18.1 (no driver attached) atapci0: <National Geode SC1100 ATA33 controller> port 0x1f0-0x1f7,0x3f6,0x170-0 x177,0x376,0xe000-0xe00f at device 18.2 on pci0 ata0: <ATA channel 0> on atapci0 ata0: [ITHREAD] ata1: <ATA channel 1> on atapci0 ata1: [ITHREAD] pci0: <bridge> at device 18.5 (no driver attached) ohci0: <OHCI (generic) USB controller> mem 0xa0003000-0xa0003fff irq 11 at devic e 19.0 on pci0 ohci0: [GIANT-LOCKED] ohci0: [ITHREAD] usb0: OHCI version 1.0, legacy support usb0: <OHCI (generic) USB controller> on ohci0 usb0: USB revision 1.0 uhub0: <(0x0e11) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0 uhub0: 3 ports with 3 removable, self powered pmtimer0 on isa0 orm0: <ISA Option ROM> at iomem 0xc8000-0xd0fff pnpid ORM0000 on isa0 atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 kbd0 at atkbd0 atkbd0: [GIANT-LOCKED] atkbd0: [ITHREAD] psm0: unable to get the current command byte value. ppc0: parallel port not found. sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 sio0: type 16550A, console sio0: [FILTER] sio1 at port 0x2f8-0x2ff irq 3 on isa0 sio1: type 16550A sio1: [FILTER] Timecounters tick every 6.666 msec hptrr: no controller detected. ad0: 1953MB <SanDisk SDCFH-2048 HDX 4.04> at ata0-master WDMA2 Trying to mount root from ufs:/dev/ad0s1a Invalid time in clock: check and reset the date! Waiting (max 60 seconds) for system process `vnlru to stop...done Waiting (max 60 seconds) for system process `bufdaemon to stop...done Waiting (max 60 seconds) for system process `syncer to stop... Syncing disks, vnodes remaining...0 done All buffers synced. Uptime: 8m30s Rebooting... Copyright (c) 1992-2008 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 7.0-RELEASE-p2 #0: Tue Aug 19 23:21:54 EDT 2008 [_EMAIL_XXXXXXXX]:/usr/obj/nanobsd.ike2/usr/src/sys/ike1.kcfg Timecounter i8254 frequency 1193182 Hz quality 0 CPU: Geode(TM) Integrated Processor by National Semi (266.60-MHz 586-class CPU) Origin = Geode by NSC Id = 0x540 Stepping = 0 Features=0x808131<FPU,TSC,MSR,CX8,CMOV,MMX> real memory = 134217728 (128 MB) avail memory = 117444608 (112 MB) kbd1 at kbdmux0 ath_hal:[_IP_XXX] (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413) hptrr: HPT RocketRAID controller driver v1.1 (Aug 19 2008 23:20:57) cpu0 on motherboard pcib0: <Host to PCI bridge> pcibus 0 on motherboard pci0: <PCI bus> on pcib0 sis0: <NatSemi DP8381[56] 10/100BaseTX> port 0xe100-0xe1ff mem 0xa0000000-0xa000 0fff irq 10 at device 6.0 on pci0 sis0: Silicon Revision: DP83816A miibus0: <MII bus> on sis0 ukphy0: <Generic IEEE 802.3u media interface> PHY 0 on miibus0 ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto sis0: Ethernet address: [_MAC_XXXXXXXXXX] sis0: [ITHREAD] sis1: <NatSemi DP8381[56] 10/100BaseTX> port 0xe200-0xe2ff mem 0xa0001000-0xa000 1fff irq 10 at device 7.0 on pci0 sis1: Silicon Revision: DP83816A miibus1: <MII bus> on sis1 ukphy1: <Generic IEEE 802.3u media interface> PHY 0 on miibus1 ukphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto sis1: Ethernet address: [_MAC_XXXXXXXXXX] sis1: [ITHREAD] sis2: <NatSemi DP8381[56] 10/100BaseTX> port 0xe300-0xe3ff mem 0xa0002000-0xa000 2fff irq 10 at device 8.0 on pci0 sis2: Silicon Revision: DP83816A miibus2: <MII bus> on sis2 ukphy2: <Generic IEEE 802.3u media interface> PHY 0 on miibus2 ukphy2: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto sis2: Ethernet address: [_MAC_XXXXXXXXXX] sis2: [ITHREAD] isab0: <PCI-ISA bridge> port 0x6100-0x613f,0x6200-0x623f at device 18.0 on pci0 isa0: <ISA bus> on isab0 pci0: <bridge> at device 18.1 (no driver attached) atapci0: <National Geode SC1100 ATA33 controller> port 0x1f0-0x1f7,0x3f6,0x170-0 x177,0x376,0xe000-0xe00f at device 18.2 on pci0 ata0: <ATA channel 0> on atapci0 ata0: [ITHREAD] ata1: <ATA channel 1> on atapci0 ata1: [ITHREAD] pci0: <bridge> at device 18.5 (no driver attached) ohci0: <OHCI (generic) USB controller> mem 0xa0003000-0xa0003fff irq 11 at devic e 19.0 on pci0 ohci0: [GIANT-LOCKED] ohci0: [ITHREAD] usb0: OHCI version 1.0, legacy support usb0: <OHCI (generic) USB controller> on ohci0 usb0: USB revision 1.0 uhub0: <(0x0e11) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0 uhub0: 3 ports with 3 removable, self powered pmtimer0 on isa0 orm0: <ISA Option ROM> at iomem 0xc8000-0xd0fff pnpid ORM0000 on isa0 atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 kbd0 at atkbd0 atkbd0: [GIANT-LOCKED] atkbd0: [ITHREAD] psm0: unable to get the current command byte value. ppc0: parallel port not found. sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 sio0: type 16550A, console sio0: [FILTER] sio1 at port 0x2f8-0x2ff irq 3 on isa0 sio1: type 16550A sio1: [FILTER] Timecounters tick every 6.666 msec hptrr: no controller detected. ad0: 1953MB <SanDisk SDCFH-2048 HDX 4.04> at ata0-master WDMA2 Trying to mount root from ufs:/dev/ad0s1a Invalid time in clock: check and reset the date!