Launched in 2004, dmesgd aims to provide a user-submitted repository of searchable *BSD dmesgs. The dmesg(8) command displays the system message buffer's content, and during boot a copy is saved to /var/run/dmesg.boot. This buffer contains the operating system release, name and version, a list of devices identified, plus a whole host of other useful information. We hope others find this resource useful and further contribute to its growth. Contact us at [ admin at lists dot nycbug dot org ]. Note that this site is not a substitute for sending the dmesg directly to the respective project.
Date: 2012-09-05 11:20:24
From: George
Description: FreeBSD 8.3 on Soekris 4801
Copyright (c) 1992-2012 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 8.3-RELEASE-p3 #0: Mon Jun 11 23:52:38 UTC 2012
root@xxxxxxxxxxxxxx:/usr/obj/usr/src/sys/GENERIC i386
module_register: module g_label already exists!
Module g_label failed to register: 17
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Geode(TM) Integrated Processor by National Semi (266.65-MHz 586-class CPU)
Origin = "Geode by NSC" Id = 0x540 Family = 5 Model = 4 Stepping = 0
Features=0x808131<FPU,TSC,MSR,CX8,CMOV,MMX>
real memory = 268435456 (256 MB)
avail memory = 243757056 (232 MB)
kbd1 at kbdmux0
ACPI Error: A valid RSDP was not found (20101013/tbxfroot-309)
ACPI: Table initialisation failed: AE_NOT_FOUND
ACPI: Try disabling either ACPI or apic support.
pcib0: <Host to PCI bridge> pcibus 0 on motherboard
pci0: <PCI bus> on pcib0
sis0: <NatSemi DP8381[56] 10/100BaseTX> port 0xe100-0xe1ff mem 0xa0000000-0xa0000fff irq 10 at device 6.0 on pci0
sis0: Silicon Revision: DP83816A
miibus0: <MII bus> on sis0
nsphyter0: <DP83815 10/100 media interface> PHY 0 on miibus0
nsphyter0: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
sis0: Ethernet address: [_MAC_XXXXXXXXXX]
sis0: [ITHREAD]
sis1: <NatSemi DP8381[56] 10/100BaseTX> port 0xe200-0xe2ff mem 0xa0001000-0xa0001fff irq 10 at device 7.0 on pci0
sis1: Silicon Revision: DP83816A
miibus1: <MII bus> on sis1
nsphyter1: <DP83815 10/100 media interface> PHY 0 on miibus1
nsphyter1: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
sis1: Ethernet address: [_MAC_XXXXXXXXXX]
sis1: [ITHREAD]
sis2: <NatSemi DP8381[56] 10/100BaseTX> port 0xe300-0xe3ff mem 0xa0002000-0xa0002fff irq 10 at device 8.0 on pci0
sis2: Silicon Revision: DP83816A
miibus2: <MII bus> on sis2
nsphyter2: <DP83815 10/100 media interface> PHY 0 on miibus2
nsphyter2: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
sis2: Ethernet address: [_MAC_XXXXXXXXXX]
sis2: [ITHREAD]
isab0: <PCI-ISA bridge> port 0x6100-0x613f,0x6200-0x623f at device 18.0 on pci0
isa0: <ISA bus> on isab0
pci0: <bridge> at device 18.1 (no driver attached)
atapci0: <National Geode SC1100 ATA33 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xe000-0xe00f at device 18.2 on pci0
ata0: <ATA channel> at channel 0 on atapci0
ata0: [ITHREAD]
ata1: <ATA channel> at channel 1 on atapci0
ata1: [ITHREAD]
pci0: <bridge> at device 18.5 (no driver attached)
ohci0: <OHCI (generic) USB controller> mem 0xa0003000-0xa0003fff irq 11 at device 19.0 on pci0
ohci0: [ITHREAD]
usbus0: <OHCI (generic) USB controller> on ohci0
cpu0 on motherboard
pmtimer0 on isa0
orm0: <ISA Option ROM> at iomem 0xc8000-0xd0fff pnpid ORM0000 on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
psm0: unable to get the current command byte value.
atrtc0: <AT Real Time Clock> at port 0x70 irq 8 on isa0
ppc0: parallel port not found.
uart0: <16550 or compatible> at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
uart0: [FILTER]
uart1: <16550 or compatible> at port 0x2f8-0x2ff irq 3 on isa0
uart1: [FILTER]
Timecounters tick every 1.000 msec
The GEOM class LABEL is already loaded.
usbus0: 12Mbps Full Speed USB v1.0
ugen0.1: <0x0e11> at usbus0
uhub0: <0x0e11 OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
ad0: 1953MB <SanDisk SDCFX-2048 HDX 3.22> at ata0-master WDMA2
GEOM: ad0s1: geometry does not match label (255h,63s != 16h,63s).
Root mount waiting for: usbus0
uhub0: 3 ports with 3 removable, self powered
Trying to mount root from ufs:/dev/ufs/host