Launched in 2004, dmesgd aims to provide a user-submitted repository of searchable *BSD dmesgs. The dmesg(8) command displays the system message buffer's content, and during boot a copy is saved to /var/run/dmesg.boot. This buffer contains the operating system release, name and version, a list of devices identified, plus a whole host of other useful information. We hope others find this resource useful and further contribute to its growth. Contact us at [ admin at lists dot nycbug dot org ]. Note that this site is not a substitute for sending the dmesg directly to the respective project.

Date: 2018-02-18 06:15:38
From: Sevan / Venture37
Description: G3 PowerBook (Pismo, PowerBook3,1) no airport install
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017,
    2018 The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 8.99.12 (GENERIC) #0: Sat Feb 17 08:07:06 UTC 2018
	[_EMAIL_XXXXXXXXXXXXXXXXX]:/usr/src/sys/arch/macppc/compile/GENERIC
total memory = 384 MB
avail memory = 357 MB
timecounter: Timecounters tick every 10.000 msec
Kernelized RAIDframe activated
found openpic PIC at 80040000
OpenPIC Version 1.2: Supports 4 CPUs and 64 interrupt sources.
bootpath: /pci@f2000000/mac-io@17/ata-4@1f000/disk@0:0/netbsd
mainbus0 (root)
cpu0 at mainbus0: 750 (Revision 3.0), ID 0 (primary)
cpu0: HID0 0x8050c0a4<EMCP,NAP,DPM,ICE,DCE,SGE,BTIC,BHT>, powersave: 1
cpu0: 500.00 MHz, no-parity 1MB WB L2 cache (PB SRAM) at 2.5:1 ratio
memory0 at mainbus0: len=256
spdmem0 at memory0
spdmem0: SDRAM, no parity or ECC, 128MB, 125MHz (PC-100)
spdmem0: 12 rows, 9 cols, 2 banks, 4 banks/chip, 8.0ns cycle time
spdmem0: tAA-tRCD-tRP-tRAS: 3-20-20-50
spdmem0: voltage LvTTL (not 5V tolerant), refresh time 15.625us (self-refreshing)
spdmem1 at memory0
spdmem1: SDRAM, no parity or ECC, 256MB, 133MHz (PC-133)
spdmem1: 13 rows, 9 cols, 2 banks, 4 banks/chip, 7.5ns cycle time
spdmem1: tAA-tRCD-tRP-tRAS: 3-20-20-45
spdmem1: voltage LvTTL (not 5V tolerant), refresh time 7.8us (self-refreshing)
uni_n0 at mainbus0 address 0xf8000000
ki2c0 at uni_n0 address 0xf8001000
iic0 at ki2c0: I2C bus
uninorth0 at mainbus0
pci0 at uninorth0 bus 0
pci0: i/o space, memory space enabled
pchb0 at pci0 dev 11 function 0
pchb0: Apple Computer UniNorth AGP Interface (rev. 0x00)
r128fb0 at pci0 dev 16 function 0: ATI Technologies Rage Mobility M3 (AGP) (rev. 0x02)
r128fb0: 64 MB aperture at 0xb4000000
r128fb0: LVDS output is active, enabling backlight control
wsdisplay0 at r128fb0 kbdmux 1: console (default, vt100 emulation)
wsmux1: connecting to wsdisplay0
uninorth1 at mainbus0
pci1 at uninorth1 bus 0
pci1: i/o space, memory space enabled
pchb1 at pci1 dev 11 function 0
pchb1: Apple Computer UniNorth Host-PCI Bridge (rev. 0x00)
obio0 at pci1 dev 23 function 0: addr 0x80000000
obio0: enabling KeyLargo internal modem
zsc0 at obio0 irq 22,23
zstty0 at zsc0 channel 0
zstty1 at zsc0 channel 1
davbus at obio0 offset 0x14000 not configured
pmu0 at obio0 offset 0x16000 irq 47:  rev. 12
pmu0: initializing RTC
pmu0: initializing ADB
nadb0 at pmu0: Apple Desktop Bus
pmu0: power-mgt not configured
smartbat0 at pmu0 addr 0: smart battery
 flags: 1 AC
smartbat1 at pmu0 addr 1: smart battery
 flags: 1 AC
ki2c1 at obio0
iic1 at ki2c1: I2C bus
wdc0 at obio0 offset 0x1f000 irq 19, level triggered: DMA transfer
atabus0 at wdc0 channel 0
mediabay0 at obio0 offset 0x34 irq 16 falling edge triggered
mediabay0: powering up keylargo-media-bay.. done.
wdc1 at mediabay0 offset 0x20000 irq 20, level triggered
atabus1 at wdc1 channel 0
wdc2 at obio0 offset 0x21000 irq 21, level triggered: DMA transfer
atabus2 at wdc2 channel 0
ohci0 at pci1 dev 24 function 0: Apple Computer KeyLargo USB Controller (rev. 0x00)
ohci0: interrupting at irq 27
ohci0: OHCI version 1.0
usb0 at ohci0: USB revision 1.0
ohci1 at pci1 dev 25 function 0: Apple Computer KeyLargo USB Controller (rev. 0x00)
ohci1: interrupting at irq 28
ohci1: OHCI version 1.0
usb1 at ohci1: USB revision 1.0
cbb0 at pci1 dev 26 function 0: Texas Instruments PCI1211 PCI-CardBus Bridge (rev. 0x00)
cbb0: cacheline 0x8 lattimer 0x10
cbb0: bhlc 0x21008
cbb0: interrupting at irq 58
cardslot0 at cbb0
cardbus0 at cardslot0: bus 1
pcmcia0 at cardslot0
uninorth2 at mainbus0
pci2 at uninorth2 bus 0
pci2: i/o space, memory space enabled
pchb2 at pci2 dev 11 function 0
pchb2: Apple Computer UniNorth Host-PCI Bridge (rev. 0x00)
Apple Computer PowerBook G3 Firewire (IEEE1394 serial bus, OpenHCI, revision 0x01) at pci2 dev 14 function 0 not configured
gem0 at pci2 dev 15 function 0: Apple Computer GMAC Ethernet (rev. 0x01)
gem0: interrupting at irq 41
bmtphy0 at gem0 phy 0: BCM5201 10/100 media interface, rev. 2
bmtphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
gem0: Ethernet address 00:30:65:, 10KB RX fifo, 4KB TX fifo
vmmask 7ff00000 schedmask 7ff00000 highmask 7ff00000
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
timecounter: Timecounter "mftb" frequency 24966218 Hz quality 100
uhub0 at usb0: Apple Computer (0x106b) OHCI root hub (0000), class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhub1 at usb1: Apple Computer (0x106b) OHCI root hub (0000), class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
adbkbd0 at nadb0 addr 2: PowerBook G3 keyboard
wskbd0 at adbkbd0 mux 1
wskbd0: connecting to wsdisplay0
wsmouse0 at adbkbd0 mux 0
adbms0 at nadb0 addr 3: EMP trackpad <tpad> 2-button, 400 dpi
wsmouse1 at adbms0 mux 0
adbbt0 at nadb0 addr 7: button device
AC Power: AC adapter online.
wd0 at atabus0 drive 0
wd0: <IC25N020ATCS04-0>
wd0: drive supports 16-sector PIO transfers, LBA addressing
wd0: 14403 MB, 31215 cyl, 15 head, 63 sec, 512 bytes/sect x 29498175 sectors
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd0(wdc0:0:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 4 (Ultra/66) (using DMA)
atapibus0 at atabus1: 2 targets
cd0 at atapibus0 drive 0: <LG      DVD-ROM DRN-8080B, 2000/06/19, LAB8> cdrom removable
cd0: drive supports PIO mode 4, DMA mode 2cd0(wdc1:0:0): using PIO mode 4
swwdog0: software watchdog initialized
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
kern.module.path=/stand/macppc/8.99.12/modules