Launched in 2004, dmesgd aims to provide a user-submitted repository of searchable *BSD dmesgs. The dmesg(8) command displays the system message buffer's content, and during boot a copy is saved to /var/run/dmesg.boot. This buffer contains the operating system release, name and version, a list of devices identified, plus a whole host of other useful information. We hope others find this resource useful and further contribute to its growth. Contact us at [ admin at lists dot nycbug dot org ]. Note that this site is not a substitute for sending the dmesg directly to the respective project.
Date: 2018-03-01 15:08:44
From: Sevan / Venture37
Description: iMac G5 1.8Ghz, PowerMac8,1, no bluetooth controller installed
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017,
2018 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
NetBSD 8.99.12 (JIMADOR) #28: Wed Feb 28 19:02:21 EST 2018
ml@blackbush:/stuff/build/obj/sys/arch/macppc/compile/JIMADOR
total memory = 2048 MB
oea_startup: failed to allocate DEAD ZONE: error=12
avail memory = 1966 MB
timecounter: Timecounters tick every 10.000 msec
found openpic PIC at 80040000
OpenPIC Version 1.2: Supports 4 CPUs and 124 interrupt sources.
bootpath:
mainbus0 (root)
cpu0 at mainbus0: 970FX (Revision 3.0), ID 0 (primary)
cpu0: HID0 0x913081<DOZE,DPM,NHR,TBCTRL,EXTBEN,ENATTN> 0x80000000<EMCP>, powersave: 1
memory0 at mainbus0: len=256
spdmem0 at memory0
spdmem0: DDR SDRAM, no parity or ECC, 1GB, 400MHz (PC-3200)
spdmem0: 13 rows, 11 cols, 2 ranks, 4 banks/chip, 5.0ns cycle time
spdmem0: tAA-tRCD-tRP-tRAS: 2-3-3-8
spdmem0: voltage SSTL 2.5V, refresh time 7.8us (self-refreshing)
spdmem1 at memory0
spdmem1: DDR SDRAM, no parity or ECC, 1GB, 400MHz (PC-3200)
spdmem1: 13 rows, 11 cols, 2 ranks, 4 banks/chip, 5.0ns cycle time
spdmem1: tAA-tRCD-tRP-tRAS: 2-3-3-8
spdmem1: voltage SSTL 2.5V, refresh time 7.8us (self-refreshing)
uninorth0 at mainbus0
pci0 at uninorth0 bus 0
pci0: i/o space, memory space enabled
pchb0 at pci0 dev 11 function 0
pchb0: vendor 106b product 0058 (rev. 0x00)
genfb0 at pci0 dev 16 function 0: vendor 10de product 0329 (rev. 0xa1)
genfb0: framebuffer at 0xa0008000, size 1440x900, depth 8, stride 1536
wsdisplay0 at genfb0 kbdmux 1: console (default, vt100 emulation)
wsmux1: connecting to wsdisplay0
drm at genfb0 not configured
ibmcpc0 at mainbus0
Mapping in config space @ pa 0xf2000000, size: 0x02800000
pci1 at ibmcpc0 bus 3
pci1: i/o space, memory space enabled
gem0 at pci1 dev 15 function 0: vendor 106b product 0051 (rev. 0x00)
gem0: interrupting at irq 40
bmtphy0 at gem0 phy 0: BCM5221 10/100 media interface, rev. 4
bmtphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
gem0: Ethernet address 00:0d:93:, 10KB RX fifo, 4KB TX fifo
pci2 at ibmcpc0 bus 1
pci2: i/o space, memory space enabled
vendor 14e4 product 4320 (miscellaneous network, revision 0x03) at pci2 dev 1 function 0 not configured
obio0 at pci2 dev 7 function 0: addr 0x80000000
mpic at obio0 offset 0x40000 not configured
zsc0 at obio0 irq 23,24
zstty0 at zsc0 channel 0
zstty1 at zsc0 channel 1
ki2c0 at obio0
iic0 at ki2c0: I2C bus
cereal at iic0 addr 0x60 not configured
deq0 at iic0 addr 0x35 Audio Codec (tas3004)
i2s at obio0 offset 0x0 not configured
ohci0 at pci2 dev 11 function 0: vendor 1033 product 0035 (rev. 0x43)
ohci0: interrupting at irq 70
ohci0: OHCI version 1.0
usb0 at ohci0: USB revision 1.0
ohci1 at pci2 dev 11 function 1: vendor 1033 product 0035 (rev. 0x43)
ohci1: interrupting at irq 70
ohci1: OHCI version 1.0
usb1 at ohci1: USB revision 1.0
ehci0 at pci2 dev 11 function 2: vendor 1033 product 00e0 (rev. 0x04)
ehci0: interrupting at irq 70
ehci0: EHCI version 1.0
ehci0: 2 companion controllers, 3 ports each: ohci0 ohci1
usb2 at ehci0: USB revision 2.0
pci3 at ibmcpc0 bus 2
pci3: i/o space, memory space enabled
vendor 1166 product 0240 (IDE mass storage, interface 0x8f) at pci3 dev 12 function 0 not configured
wdc0 at pci3 dev 13 function 0: interrupting at irq 38
atabus0 at wdc0 channel 0
vendor 106b product 0052 (IEEE1394 serial bus, OpenHCI) at pci3 dev 14 function 0 not configured
smu0 at mainbus0 mbox 0x860c gpio 0x62 irq 53smu0: unable to register with sysmon
using 0 fans for CPU zone
using 0 fans for drive bay zone
using 0 fans for expansion slots zone
vmmask 7e000000 schedmask 7e000000 highmask 7e000000
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
timecounter: Timecounter "mftb" frequency 33333333 Hz quality 100
uhub0 at usb0: vendor 1033 (0x1033) OHCI root hub (0000), class 9/0, rev 1.00/1.00, addr 1
uhub0: 3 ports with 3 removable, self powered
uhub1 at usb1: vendor 1033 (0x1033) OHCI root hub (0000), class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhub2 at usb2: vendor 1033 (0x1033) EHCI root hub (0000), class 9/0, rev 2.00/1.00, addr 1
uhub2: 5 ports with 5 removable, self powered
atapibus0 at atabus0: 2 targets
cd0 at atapibus0 drive 0: <MATSHITADVD-R UJ-825, , DBN7> cdrom removable
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 4 (Ultra/66)
cd0(wdc0:0:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 4 (Ultra/66) (using DMA)
ehci0: handing over full speed device on port 2 to ohci0
uhidev0 at uhub1 port 1 configuration 1 interface 0
uhidev0: City Ergonomics (0xd209) DXT Mouse (0xf224), rev 2.00/1.00, addr 2, iclass 3/0
ums0 at uhidev0: 5 buttons and Z dir
wsmouse0 at ums0 mux 0
uhub3 at uhub2 port 3: Apple, Inc. (0x5ac) Keyboard Hub (0x1006), class 9/0, rev 2.00/95.15, addr 2
uhub3: single transaction translator
uhub3: 3 ports with 2 removable, bus powered
uhidev1 at uhub3 port 2 configuration 1 interface 0
uhidev1: Apple, Inc (0x5ac) Apple Keyboard (0x221), rev 2.00/0.69, addr 3, iclass 3/1
ukbd0 at uhidev1: 8 Variable keys, 5 Array codes
wskbd0 at ukbd0: console keyboard, using wsdisplay0
uhidev2 at uhub3 port 2 configuration 1 interface 1
uhidev2: Apple, Inc (0x5ac) Apple Keyboard (0x221), rev 2.00/0.69, addr 3, iclass 3/0
uhid0 at uhidev2: input=1, output=0, feature=0
WARNING: 1 error while detecting hardware; check system log.
boot device: cpu0
root on gem0
nfs_boot: trying DHCP/BOOTP
nfs_boot: DHCP next-server:[_IP_XXXXX]
nfs_boot: my_addr=10.1.0.102
nfs_boot: my_mask=255.255.255.0
nfs_boot: gateway=10.1.0.100
root on[_IP_XXXXX]:/export/g5
kern.module.path=/stand/macppc/8.99.12/modules