Launched in 2004, dmesgd aims to provide a user-submitted repository of searchable *BSD dmesgs. The dmesg(8) command displays the system message buffer's content, and during boot a copy is saved to /var/run/dmesg.boot. This buffer contains the operating system release, name and version, a list of devices identified, plus a whole host of other useful information. We hope others find this resource useful and further contribute to its growth. Contact us at [ admin at lists dot nycbug dot org ]. Note that this site is not a substitute for sending the dmesg directly to the respective project.
Date: 2019-11-30 01:12:26
From: yamori813
Description: RT3883
RT3883 # bootm
FDT DTB at: 0x80388cb0
CPU clock: 500MHz
Timer clock: 250MHz
UART clock: 40MHz
U-Boot args (from 0 args):
None
Environment:
entry: mips_init()
RAM size: 32MB (assumed)
Cache info:
picache_stride = 4096
picache_loopcount = 16
pdcache_stride = 4096
pdcache_loopcount = 8
max line size = 32
cpu0: MIPS Technologies processor v76.151
MMU: Standard TLB, 32 entries (4K 16K 64K 256K 1M 16M 64M 256M pg sizes)
L1 i-cache: 4 ways of 512 sets, 32 bytes per line
L1 d-cache: 4 ways of 256 sets, 32 bytes per line
L2 cache: disabled
Config1=0xbee3519e<PerfCount,WatchRegs,MIPS16,EJTAG>
Config2=0x80000000
Config3=0x2c20<ULRI>
Config7=0x80010800<WII,AR>
Physical memory chunk(s):
0x415000 - 0x1ffffff, 29274112 bytes (7147 pages)
Maxmem is 0x2000000
---<<BOOT>>---
Copyright (c) 1992-2019 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 13.0-CURRENT #8 81cdc5bc8ba-c264170(zrouter)-dirty: Sat Nov 30 10:06:33 JST 2019
hiroki@zrouter:/usr/home/hiroki/zobj/usr/home/hiroki/ZRouter/tmp/usr/home/hiroki/freebsd/mips.mipsel/sys/IOData_WN-AG450DGR mips
gcc version 4.2.1 20070831 patched [FreeBSD]
Preloaded elf kernel "kernel" at 0x80408a28.
CPU model: RT3883
real memory = 33554432 (32768K bytes)
Physical memory chunk(s):
0x004a1000 - 0x01f81fff, 28184576 bytes (6881 pages)
avail memory = 27611136 (26MB)
arc4random: WARNING: initial seeding bypassed the cryptographic random device because it was not yet seeded and the knob 'bypass_before_seeding' was enabled.
ULE: setup cpu 0
firmware: 'rt2561sfw' version 0: 8192 bytes loaded at 0x803904a0
firmware: 'rt2661fw' version 0: 8192 bytes loaded at 0x80392520
random: entropy device external interface
wlan: <802.11 Link Layer>
firmware: 'rt2860fw' version 0: 8192 bytes loaded at 0x803945a0
firmware: 'rt2561fw' version 0: 8192 bytes loaded at 0x8038e420
mem: <memory>
null: <full device, null device, zero device>
openfirm: <Open Firmware control device>
nexus0: <MIPS32 root nexus>
ofwbus0: <Open Firmware Device Tree> on nexus0
palmbus0: <MTK Palmbus> mem 0x10000000-0x101fffff on ofwbus0
cpupic0: <MIPS32 Interrupt Controller> on ofwbus0
sysc0: <MTK System Controller> mem 0-0xff on palmbus0
pinctrl0: <MTK Pin Controller> on ofwbus0
pinctrl0: GPIO mode start: 0x00001c01
Processing 1 pin-config node(s) in pinctrl-0 for spi@b00
Processing 1 pin-config node(s) in pinctrl-0 for uartlite@c00
Processing 1 pin-config node(s) in pinctrl-0 for pinctrl
pinctrl0: GPIO mode end : 0x00001c5d
rstctrl0: <MTK Reset Controller> on ofwbus0
clkctrl0: <MTK Clock Controller> on ofwbus0
intc0: <MTK Interrupt Controller (v2)> mem 0x200-0x2ff irq 7 on palmbus0
gpio0: <MTK GPIO Controller (v1)> mem 0x600-0x633 irq 10 on palmbus0
gpiobus0: <OFW GPIO bus> on gpio0
cpulist0: <Open Firmware CPU Group> on ofwbus0
palmbus0: <timer@100> mem 0x100-0x11f irq 5 compat ralink,rt3883-timer (no driver attached)
palmbus0: <watchdog@120> mem 0x120-0x12f irq 6 compat ralink,rt3883-wdt (no driver attached)
palmbus0: <memc@300> mem 0x300-0x3ff irq 8 compat ralink,rt3883-memc (no driver attached)
palmbus0: <uart@500> mem 0x500-0x5ff irq 9 disabled compat ralink,rt3883-uart (no driver attached)
gpioc0: <GPIO controller> on gpio0
palmbus0: <gpio@638> mem 0x638-0x65b disabled compat ralink,rt3883-gpio (no driver attached)
palmbus0: <gpio@660> mem 0x660-0x683 disabled compat ralink,rt3883-gpio (no driver attached)
palmbus0: <gpio@688> mem 0x688-0x6ab disabled compat ralink,rt3883-gpio (no driver attached)
spi0: <MTK SPI Controller (v1)> mem 0xb00-0xb3f on palmbus0
spi0: Warning: No cs-gpios specified in fdt data; device may not function.
spibus0: <OFW SPI bus> on spi0
mx25l0: <M25Pxx Flash Family> at cs 0 mode 0 on spibus0
mx25l0: device type mx25ll64, size 8192K in 128 sectors of 64K, erase size 64K
palmbus0: <spi@b40> mem 0xb40-0xb9f disabled compat ralink,rt3883-spi (no driver attached)
uart0: <MTK UART Controller> mem 0xc00-0xcff irq 11 on palmbus0
uart0: console (58139,n,8,1)
uart0: fast interrupt
uart0: PPS capture mode: DCD
rt0: <Ralink RT3050 onChip Ethernet driver> mem 0x10100000-0x1010ffff irq 0 on ofwbus0
rt0: RT305XF Ethernet MAC (rev 0x00000000)
rt0: use hardcoded [_MAC_XXXXXXXXXX] macaddr
rt0: bpf attached
rt0: Ethernet address: [_MAC_XXXXXXXXXX]
ofwbus0: <pci@10140000> mem 0x10140000-0x1015ffff irq 1 disabled compat ralink,rt3883-pci (no driver attached)
usbphy0: <MTK USB PHY> on ofwbus0
ofwbus0: <wmac@10180000> mem 0x10180000-0x101bffff irq 2 compat ralink,rt3883-wmac (no driver attached)
ofwbus0: <ehci@101c0000> mem 0x101c0000-0x101c0fff irq 3 compat generic-ehci (no driver attached)
ofwbus0: <ohci@101c1000> mem 0x101c1000-0x101c1fff irq 4 disabled compat generic-ohci (no driver attached)
gpioled0: <GPIO LEDs> on ofwbus0
ofwbus0: <gpio-keys-polled> compat gpio-keys-polled (no driver attached)
gpioiic0: <GPIO I2C bit-banging FDT driver> on ofwbus0
iicbb0: <I2C bit-banging driver> on gpioiic0
iicbus0: <OFW I2C bus> on iicbb0 master-only
iic0: <I2C generic I/O> on iicbus0
rtmdio0: <RT built-in ethernet interface, MDIO controller> mem 0x10100000-0x1010ffff on ofwbus0
mdio0: <MDIO> on rtmdio0
mdioproxy0: <MII/MDIO proxy, MDIO side> on mdio0
arswitch0: <Atheros AR8327 Ethernet Switch (ver 1 rev 2)> on mdio0
arswitch0: ar8327_phy_fixup: called; phy=0; chiprev=2
arswitch0: ar8327_phy_fixup: called; phy=1; chiprev=2
arswitch0: ar8327_phy_fixup: called; phy=2; chiprev=2
arswitch0: ar8327_phy_fixup: called; phy=3; chiprev=2
arswitch0: ar8327_phy_fixup: called; phy=4; chiprev=2
arswitch0: ar8327_atu_learn_default: TODO!
miibus0: <MII bus> on arswitch0
ukphy0: <Generic IEEE 802.3u media interface> PHY 0 on miibus0
ukphy0: OUI 0x00c82e, model 0x0003, rev. 3
ukphy0: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT-FDX, 1000baseT-FDX-master, auto
miibus1: <MII bus> on arswitch0
ukphy1: <Generic IEEE 802.3u media interface> PHY 1 on miibus1
ukphy1: OUI 0x00c82e, model 0x0003, rev. 3
ukphy1: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT-FDX, 1000baseT-FDX-master, auto
miibus2: <MII bus> on arswitch0
ukphy2: <Generic IEEE 802.3u media interface> PHY 2 on miibus2
ukphy2: OUI 0x00c82e, model 0x0003, rev. 3
ukphy2: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT-FDX, 1000baseT-FDX-master, auto
miibus3: <MII bus> on arswitch0
ukphy3: <Generic IEEE 802.3u media interface> PHY 3 on miibus3
ukphy3: OUI 0x00c82e, model 0x0003, rev. 3
ukphy3: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT-FDX, 1000baseT-FDX-master, auto
miibus4: <MII bus> on arswitch0
ukphy4: <Generic IEEE 802.3u media interface> PHY 4 on miibus4
ukphy4: OUI 0x00c82e, model 0x0003, rev. 3
ukphy4: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT-FDX, 1000baseT-FDX-master, auto
etherswitch0: <Switch controller> on arswitch0
mdio1: <MDIO> on arswitch0
mdioproxy1: <MII/MDIO proxy, MDIO side> on mdio1
clock0: <Generic MIPS32 ticker> on nexus0
Timecounter "MIPS32" frequency 250000000 Hz quality 800
Event timer "MIPS32" frequency 250000000 Hz quality 800
Device configuration finished.
Timecounters tick every 10.000 msec
lo0: bpf attached
vlan: initialized, using hash tables with chaining
tcp_init: net.inet.tcp.tcbhashsize auto tuned to 512
usb_needs_explore_all: no devclass
arswitch0port1: link state changed to DOWN
arswitch0port2: link state changed to DOWN
arswitch0port3: link state changed to DOWN
arswitch0port4: link state changed to DOWN
arswitch0port5: link state changed to DOWN
GEOM: new disk flash/spi0
Trying to mount root from cd9660:spi0s.rootfs.uzip []...
MAP: No valid partition found at flash/spi0
flash/spi0: slice 00000000-0000ffff: u-boot (63KB)
flash/spi0: slice 00010000-0001ffff: u-boot-env (63KB)
flash/spi0: slice 00040000-0073ffff: rootfs (7167KB)
MAP: No valid partition found at flash/spi0s.u-boot
MAP: No valid partition found at flash/spi0s.u-boot-env
MAP: No valid partition found at flash/spi0s.rootfs
mountroot: waiting for device spi0s.rootfs.uzip...
arswitch0: arswitch_miipollstat: port 1: port -> UP
arswitch0port2: link state changed to UP
Mounting from cd9660:spi0s.rootfs.uzip failed with error 19.
Loader variables:
Manual root filesystem specification:
<fstype>:<device> [options]
Mount <device> using filesystem <fstype>
and with the specified (optional) option list.
eg. ufs:/dev/da0s1a
zfs:zroot/ROOT/default
cd9660:/dev/cd0 ro
(which is equivalent to: mount -t cd9660 -o ro /dev/cd0 /)
? List valid disk boot devices
. Yield 1 second (for background tasks)
<empty line> Abort manual input
mountroot>