Launched in 2004, dmesgd aims to provide a user-submitted repository of searchable *BSD dmesgs. The dmesg(8) command displays the system message buffer's content, and during boot a copy is saved to /var/run/dmesg.boot. This buffer contains the operating system release, name and version, a list of devices identified, plus a whole host of other useful information. We hope others find this resource useful and further contribute to its growth. Contact us at [ admin at lists dot nycbug dot org ]. Note that this site is not a substitute for sending the dmesg directly to the respective project.
Date: 2019-12-04 08:39:03
From: yamori813
Description: Planex_MZK-W300NAG
---<<BOOT>>---
KDB: debugger backends: ddb
KDB: current backend: ddb
Copyright (c) 1992-2019 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 13.0-CURRENT #9 cdad3a2727d-c265408(zrouter)-dirty: Wed Dec 4 17:30:58 JST 2019
hiroki@zrouter:/usr/home/hiroki/zobj/usr/home/hiroki/ZRouter/tmp/usr/home/hiroki/freebsd/mips.mipsel/sys/Planex_MZK-W300NAG mips
gcc version 4.2.1 20070831 patched [FreeBSD]
Preloaded elf kernel "kernel" at 0x883808f8.
CPU model: RT2880
real memory = 16777216 (16384K bytes)
Physical memory chunk(s):
0x08419000 - 0x08fc4fff, 12238848 bytes (2988 pages)
avail memory = 11751424 (11MB)
random: no preloaded entropy cache
arc4random: WARNING: initial seeding bypassed the cryptographic random device because it was not yet seeded and the knob 'bypass_before_seeding' was enabled.
ULE: setup cpu 0
random: entropy device external interface
null: <full device, null device, zero device>
openfirm: <Open Firmware control device>
WARNING: Device "openfirm" is Giant locked and may be deleted before FreeBSD 13.0.
mem: <memory>
nexus0: <MIPS32 root nexus>
ofwbus0: <Open Firmware Device Tree> on nexus0
palmbus0: <MTK Palmbus> mem 0x300000-0x4fffff on ofwbus0
cpupic0: <MIPS32 Interrupt Controller> on ofwbus0
sysc0: <MTK System Controller> mem 0-0xff on palmbus0
pinctrl0: <MTK Pin Controller> on ofwbus0
pinctrl0: GPIO mode start: 0x00000026
Processing 1 pin-config node(s) in pinctrl-0 for i2c@900
Processing 1 pin-config node(s) in pinctrl-0 for pinctrl
pinctrl0: GPIO mode end : 0x00000026
rstctrl0: <MTK Reset Controller> on ofwbus0
clkctrl0: <MTK Clock Controller> on ofwbus0
intc0: <MTK Interrupt Controller (v2)> mem 0x200-0x2ff irq 3 on palmbus0
gpio0: <MTK GPIO Controller (v1)> mem 0x600-0x633 irq 4 on palmbus0
gpiobus0: <OFW GPIO bus> on gpio0
cpulist0: <Open Firmware CPU Group> on ofwbus0
palmbus0: <timer@100> mem 0x100-0x11f irq 2 disabled compat ralink,rt2880-timer (no driver attached)
palmbus0: <watchdog@120> mem 0x120-0x12f compat ralink,rt2880-wdt (no driver attached)
palmbus0: <memc@300> mem 0x300-0x3ff compat ralink,rt2880-memc (no driver attached)
gpioc0: <GPIO controller> on gpio0
palmbus0: <gpio@638> mem 0x638-0x65b disabled compat ralink,rt2880-gpio (no driver attached)
palmbus0: <gpio@660> mem 0x660-0x683 disabled compat ralink,rt2880-gpio (no driver attached)
iichb0: <MTK I2C Controller> mem 0x900-0x9ff on palmbus0
iicbus0: <OFW I2C bus> on iichb0
iicbus0: <unknown card> at addr 0xa8
iic0: <I2C generic I/O> on iicbus0
iicbus0: <unknown card> at addr 0xa0
uart0: <MTK UART Controller> mem 0xc00-0xcff irq 5 on palmbus0
uart0: console (57870,n,8,1)
uart0: fast interrupt
uart0: PPS capture mode: DCD
rt0: <Ralink RT2880 onChip Ethernet driver> mem 0x400000-0x40ffff irq 0 disabled on ofwbus0
rt0: RT305XF Ethernet MAC (rev 0x00000000)
rt0: use hardcoded [_MAC_XXXXXXXXXX] macaddr
rt0: bpf attached
rt0: Ethernet address: [_MAC_XXXXXXXXXX]
ofwbus0: <mdio-bus> mem 0x400000-0x40ffff compat ralink,rt2880-mdio (no driver attached)
ofwbus0: <wmac@480000> mem 0x480000-0x4bffff irq 1 compat ralink,rt2880-wmac (no driver attached)
cfi0: <AMD/Fujitsu - 4MB> mem 0x1f000000-0x1f7fffff on ofwbus0
cfi0: [8x8KB,63x64KB]
cfi0: Manufacturer ID:c2 Device ID:22a8
cfid0 on cfi0
gpioled0: <GPIO LEDs> on ofwbus0
ofwbus0: <gpio-keys-polled> compat gpio-keys-polled (no driver attached)
gpioiic0: <GPIO I2C bit-banging FDT driver> on ofwbus0
iicbb0: <I2C bit-banging driver> on gpioiic0
iicbus1: <OFW I2C bus> on iicbb0 master-only
rtl8366rb1: <RTL8366SR Ethernet Switch Controller> at addr 0xa8 on iicbus1
rtl8366rb1: rev. 1
miibus0: <MII bus> on rtl8366rb1
ukphy0: <Generic IEEE 802.3u media interface> PHY 0 on miibus0
ukphy0: OUI 0x00e04c, model 0x0016, rev. 0
ukphy0: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
miibus1: <MII bus> on rtl8366rb1
ukphy1: <Generic IEEE 802.3u media interface> PHY 1 on miibus1
ukphy1: OUI 0x00e04c, model 0x0016, rev. 0
ukphy1: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
miibus2: <MII bus> on rtl8366rb1
ukphy2: <Generic IEEE 802.3u media interface> PHY 2 on miibus2
ukphy2: OUI 0x00e04c, model 0x0016, rev. 0
ukphy2: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
miibus3: <MII bus> on rtl8366rb1
ukphy3: <Generic IEEE 802.3u media interface> PHY 3 on miibus3
ukphy3: OUI 0x00e04c, model 0x0016, rev. 0
ukphy3: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
miibus4: <MII bus> on rtl8366rb1
ukphy4: <Generic IEEE 802.3u media interface> PHY 4 on miibus4
ukphy4: OUI 0x00e04c, model 0x0016, rev. 0
ukphy4: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
etherswitch0: <Switch controller> on rtl8366rb1
iic1: <I2C generic I/O> on iicbus1
ofwbus0: <rtl8366rb> compat realtek,rtl8366rb (no driver attached)
clock0: <Generic MIPS32 ticker> on nexus0
Timecounter "MIPS32" frequency 133333333 Hz quality 800
Event timer "MIPS32" frequency 133333333 Hz quality 800
Device configuration finished.
Timecounters tick every 10.000 msec
lo0: bpf attached
tcp_init: net.inet.tcp.tcbhashsize auto tuned to 512
rtl8366rb1port0: link state changed to DOWN
rtl8366rb1port1: link state changed to DOWN
rtl8366rb1port2: link state changed to DOWN
rtl8366rb1port3: link state changed to DOWN
rtl8366rb1port4: link state changed to DOWN
GEOM: new disk cfid0
Trying to mount root from cd9660:cfid0s.rootfs.uzip []...
cfid0: slice 00000000-0002ffff: Bootloader (191KB)
cfid0: slice 00030000-0003ffff: Config (63KB)
cfid0: slice 00040000-0004ffff: Factory (63KB)
cfid0: slice 00150000-003dffff: rootfs (2623KB)
cfid0: slice 00050000-003dffff: upgrade (3647KB)
cfid0: slice 003e0000-003fffff: Cimage (127KB)
cd9660: RockRidge Extension
Warning: no time-of-day clock registered, system time will not be set accurately
start_init: trying /sbin/init
rtl8366rb1port3: link state changed to UP
random: unblocking device.
lo0: link state changed to UP
/tmp: optimization changed from SPACE to TIME