Launched in 2004, dmesgd aims to provide a user-submitted repository of searchable *BSD dmesgs. The dmesg(8) command displays the system message buffer's content, and during boot a copy is saved to /var/run/dmesg.boot. This buffer contains the operating system release, name and version, a list of devices identified, plus a whole host of other useful information. We hope others find this resource useful and further contribute to its growth. Contact us at [ admin at lists dot nycbug dot org ]. Note that this site is not a substitute for sending the dmesg directly to the respective project.


Date: 2020-05-30 17:48:36
From: darkain
Description: Raspberry Pi 4b 4GB (PCIe/USB driver test)
---<<BOOT>>---
KDB: debugger backends: ddb
KDB: current backend: ddb
Copyright (c) 1992-2020 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 13.0-CURRENT #0 r361645M: Thu May 28 12:02:43 UTC 2020
    root@generic:/usr/obj/usr/src/arm64.aarch64/sys/GENERIC arm64
FreeBSD clang version 10.0.1 ([_EMAIL_XXXXX]:llvm/llvm-project.git llvmorg-10.0.1-rc1-0-gf79cd71e145)
WARNING: WITNESS option enabled, expect reduced performance.
VT(efifb): resolution 1280x1024
module firmware already present!
KLD file umodem.ko is missing dependencies
module_register: cannot register simplebus/pcib from kernel; already loaded from kernel
Module simplebus/pcib failed to register: 17
Starting CPU 1 (1)
Starting CPU 2 (2)
Starting CPU 3 (3)
FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
random: unblocking device.
random: entropy device external interface
MAP 39f45000 mode 2 pages 1
MAP 39f49000 mode 2 pages 2
MAP 3b350000 mode 2 pages 16
MAP fe100000 mode 0 pages 1
WARNING: Device "kbd" is Giant locked and may be deleted before FreeBSD 13.0.
kbd0 at kbdmux0
WARNING: Device "openfirm" is Giant locked and may be deleted before FreeBSD 13.0.
ofwbus0: <Open Firmware Device Tree>
simplebus0: <Flattened device tree simple bus> on ofwbus0
ofw_clkbus0: <OFW clocks bus> on ofwbus0
clk_fixed0: <Fixed clock> on ofw_clkbus0
clk_fixed1: <Fixed clock> on ofw_clkbus0
simplebus1: <Flattened device tree simple bus> on ofwbus0
simplebus2: <Flattened device tree simple bus> on ofwbus0
regfix0: <Fixed Regulator> on ofwbus0
regfix1: <Fixed Regulator> on ofwbus0
psci0: <ARM Power State Co-ordination Interface Driver> on ofwbus0
gic0: <ARM Generic Interrupt Controller> mem 0x40041000-0x40041fff,0x40042000-0x40043fff,0x40044000-0x40045fff,0x40046000-0x40047fff irq 46 on simplebus0
gic0: pn 0x2, arch 0x2, rev 0x1, implementer 0x43b irqs 256
gpio0: <BCM2708/2835 GPIO controller> mem 0x7e200000-0x7e2000b3 irq 22,23 on simplebus0
gpiobus0: <OFW GPIO bus> on gpio0
gpioregulator0: <GPIO controlled regulator> on ofwbus0
gpioregulator0: cannot get pin 0
gpioregulator0: cannot parse parameters
device_attach: gpioregulator0 attach returned 6
generic_timer0: <ARMv7 Generic Timer> irq 4,5,6,7 on ofwbus0
Timecounter "ARM MPCore Timecounter" frequency 54000000 Hz quality 1000
Event timer "ARM MPCore Eventtimer" frequency 54000000 Hz quality 1000
gpioregulator0: <GPIO controlled regulator> on ofwbus0
gpioregulator0: cannot get pin 0
gpioregulator0: cannot parse parameters
device_attach: gpioregulator0 attach returned 6
gpioregulator0: <GPIO controlled regulator> on ofwbus0
gpioregulator0: cannot get pin 0
gpioregulator0: cannot parse parameters
device_attach: gpioregulator0 attach returned 6
gpioregulator0: <GPIO controlled regulator> on ofwbus0
gpioregulator0: cannot get pin 0
gpioregulator0: cannot parse parameters
device_attach: gpioregulator0 attach returned 6
gpioregulator0: <GPIO controlled regulator> on ofwbus0
gpioregulator0: cannot get pin 0
gpioregulator0: cannot parse parameters
device_attach: gpioregulator0 attach returned 6
usb_nop_xceiv0: <USB NOP PHY> on ofwbus0
gpioregulator0: <GPIO controlled regulator> on ofwbus0
gpioregulator0: cannot get pin 0
gpioregulator0: cannot parse parameters
device_attach: gpioregulator0 attach returned 6
bcm_dma0: <BCM2835 DMA Controller> mem 0x7e007000-0x7e007aff irq 9,10,11,12,13,14,15,16,17,18,19 on simplebus0
bcmwd0: <BCM2708/2835 Watchdog> mem 0x7e100000-0x7e100113,0x7e00a000-0x7e00a023,0x7ec11000-0x7ec1101f on simplebus0
mbox0: <BCM2835 VideoCore Mailbox> mem 0x7e00b880-0x7e00b8bf irq 21 on simplebus0
gpioc0: <GPIO controller> on gpio0
uart0: <PrimeCell UART (PL011)> mem 0x7e201000-0x7e2011ff irq 24 on simplebus0
uart0: console (115200,n,8,1)
spi0: <BCM2708/2835 SPI controller> mem 0x7e204000-0x7e2041ff irq 26 on simplebus0
spibus0: <OFW SPI bus> on spi0
spibus0: <unknown card> at cs 0 mode 0
spibus0: <unknown card> at cs 1 mode 0
iichb0: <BCM2708/2835 BSC controller> mem 0x7e804000-0x7e804fff irq 38 on simplebus0
sdhci_bcm0: <Broadcom 2708 SDHCI controller> mem 0x7e340000-0x7e3400ff irq 60 on simplebus0
mmc0: <MMC/SD bus> on sdhci_bcm0
sdhci_bcm1: <Broadcom 2708 SDHCI controller> mem 0x7e300000-0x7e3000ff irq 61 on simplebus0
mmc1: <MMC/SD bus> on sdhci_bcm1
fb0: <BCM2835 VT framebuffer driver> on simplebus0
fb0: keeping existing fb bpp of 32
fbd0 on fb0
WARNING: Device "fb" is Giant locked and may be deleted before FreeBSD 13.0.
VT: Replacing driver "efifb" with new "fb".
fb0: 1280x1024(1280x1024@0,0) 32bpp
fb0: fbswap: 1, pitch 5120, base 0x3e6fa000, screen_size 5242880
cpulist0: <Open Firmware CPU Group> on ofwbus0
cpu0: <Open Firmware CPU> on cpulist0
cpu1: <Open Firmware CPU> on cpulist0
cpu2: <Open Firmware CPU> on cpulist0
cpu3: <Open Firmware CPU> on cpulist0
pcib0: <BCM2838-compatible PCI-express controller> mem 0x7d500000-0x7d50930f,0x7e00f300-0x7e00f31f irq 66,67 on simplebus2
pcib0: hardware identifies as revision 0x304.
pci0: <PCI bus> on pcib0
pcib1: <PCI-PCI bridge> irq 77 at device 0.0 on pci0
pcib0: bcm_pcib_alloc_resource FAIL: type=3, rid=36, start=00000000f8000000, end=00000000f80fffff, count=0000000000100000, flags=40
pcib1: failed to allocate initial prefetch window: 0-0xfffff
pci1: <PCI bus> on pcib1
xhci0: <XHCI (generic) USB 3.0 controller> irq 78 at device 0.0 on pci1
xhci0: 32 bytes context size, 64-bit DMA
usbus0 on xhci0
genet0: <RPi4 Gigabit Ethernet> mem 0x7d580000-0x7d58ffff irq 68,69 on simplebus2
genet0: GENET version 5.0 phy 0x0000
miibus0: <MII bus> on genet0
ukphy0: <Generic IEEE 802.3u media interface> PHY 1 on miibus0
ukphy0:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow
genet0: Ethernet address: [_MAC_XXXXXXXXXX]
gpioled0: <GPIO LEDs> on ofwbus0
gpioled0: <led1> failed to map pin
gpioregulator0: <GPIO controlled regulator> on ofwbus0
gpioregulator0: cannot get pin 0
gpioregulator0: cannot parse parameters
device_attach: gpioregulator0 attach returned 6
cryptosoft0: <software crypto>
Timecounters tick every 1.000 msec
usbus0: 5.0Gbps Super Speed USB v3.0
Obsolete code will be removed soon: random(9) is the obsolete Park-Miller LCG from 1988
iicbus0: <OFW I2C bus> on iichb0
iic0: <I2C generic I/O> on iicbus0
ugen0.1: <0x1106 XHCI root HUB> at usbus0
uhub0 on usbus0
uhub0: <0x1106 XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus0
mmcsd0: 32GB <SDHC SC32G 8.0 SN E3224292 MFG 11/2019 by 3 SD> at mmc0 50.0MHz/4bit/65535-block
sdhci_bcm1-slot0: Got command interrupt 0x00030000, but there is no active command.
sdhci_bcm1-slot0: ============== REGISTER DUMP ==============
sdhci_bcm1-slot0: Sys addr: 0x00000000 | Version:  0x00009902
sdhci_bcm1-slot0: Blk size: 0x00000000 | Blk cnt:  0x00000000
sdhci_bcm1-slot0: Argument: 0x000001aa | Trn mode: 0x00000000
sdhci_bcm1-slot0: Present:  0x000f0000 | Host ctl: 0x00000001
sdhci_bcm1-slot0: Power:    0x0000000f | Blk gap:  0x00000000
sdhci_bcm1-slot0: Wake-up:  0x00000000 | Clock:    0x0000fa07
sdhci_bcm1-slot0: Timeout:  0x00000000 | Int stat: 0x00000000
sdhci_bcm1-slot0: Int enab: 0x01ff00bb | Sig enab: 0x01ff00bb
sdhci_bcm1-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000
sdhci_bcm1-slot0: Caps:     0x00000000 | Caps2:    0x00000000
sdhci_bcm1-slot0: Max curr: 0x00000001 | ADMA err: 0x00000000
sdhci_bcm1-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000
sdhci_bcm1-slot0: ===========================================
sdhci_bcm1-slot0: Got command interrupt 0x00030000, but there is no active command.
sdhci_bcm1-slot0: ============== REGISTER DUMP ==============
sdhci_bcm1-slot0: Sys addr: 0x00000000 | Version:  0x00009902
sdhci_bcm1-slot0: Blk size: 0x00000000 | Blk cnt:  0x00000000
sdhci_bcm1-slot0: Argument: 0x00000000 | Trn mode: 0x00000000
sdhci_bcm1-slot0: Present:  0x000f0000 | Host ctl: 0x00000001
sdhci_bcm1-slot0: Power:    0x0000000f | Blk gap:  0x00000000
sdhci_bcm1-slot0: Wake-up:  0x00000000 | Clock:    0x0000fa07
sdhci_bcm1-slot0: Timeout:  0x00000000 | Int stat: 0x00000000
sdhci_bcm1-slot0: Int enab: 0x01ff00bb | Sig enab: 0x01ff00bb
sdhci_bcm1-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000
sdhci_bcm1-slot0: Caps:     0x00000000 | Caps2:    0x00000000
sdhci_bcm1-slot0: Max curr: 0x00000001 | ADMA err: 0x00000000
sdhci_bcm1-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000
sdhci_bcm1-slot0: ===========================================
sdhci_bcm1-slot0: Got command interrupt 0x00030000, but there is no active command.
sdhci_bcm1-slot0: ============== REGISTER DUMP ==============
sdhci_bcm1-slot0: Sys addr: 0x00000000 | Version:  0x00009902
sdhci_bcm1-slot0: Blk size: 0x00000000 | Blk cnt:  0x00000000
sdhci_bcm1-slot0: Argument: 0x00000000 | Trn mode: 0x00000000
sdhci_bcm1-slot0: Present:  0x000f0000 | Host ctl: 0x00000001
sdhci_bcm1-slot0: Power:    0x0000000f | Blk gap:  0x00000000
sdhci_bcm1-slot0: Wake-up:  0x00000000 | Clock:    0x0000fa07
sdhci_bcm1-slot0: Timeout:  0x00000000 | Int stat: 0x00000000
sdhci_bcm1-slot0: Int enab: 0x01ff00bb | Sig enab: 0x01ff00bb
sdhci_bcm1-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000
sdhci_bcm1-slot0: Caps:     0x00000000 | Caps2:    0x00000000
sdhci_bcm1-slot0: Max curr: 0x00000001 | ADMA err: 0x00000000
sdhci_bcm1-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000
sdhci_bcm1-slot0: ===========================================
sdhci_bcm1-slot0: Got command interrupt 0x00030000, but there is no active command.
sdhci_bcm1-slot0: ============== REGISTER DUMP ==============
sdhci_bcm1-slot0: Sys addr: 0x00000000 | Version:  0x00009902
sdhci_bcm1-slot0: Blk size: 0x00000000 | Blk cnt:  0x00000000
sdhci_bcm1-slot0: Argument: 0x00000000 | Trn mode: 0x00000000
sdhci_bcm1-slot0: Present:  0x000f0000 | Host ctl: 0x00000001
sdhci_bcm1-slot0: Power:    0x0000000f | Blk gap:  0x00000000
sdhci_bcm1-slot0: Wake-up:  0x00000000 | Clock:    0x0000fa07
sdhci_bcm1-slot0: Timeout:  0x00000000 | Int stat: 0x00000000
sdhci_bcm1-slot0: Int enab: 0x01ff00bb | Sig enab: 0x01ff00bb
sdhci_bcm1-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000
sdhci_bcm1-slot0: Caps:     0x00000000 | Caps2:    0x00000000
sdhci_bcm1-slot0: Max curr: 0x00000001 | ADMA err: 0x00000000
sdhci_bcm1-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000
sdhci_bcm1-slot0: ===========================================
mmc1: No compatible cards found on bus
Release APs...done
CPU  0: ARM Cortex-A72 r0p3 affinity:  0
                   Cache Type = <64 byte D-cacheline,64 byte I-cacheline,PIPT ICache,64 byte ERG,64 byte CWG>
Trying to mount root from ufs:/dev/ufs/rootfs [rw]...
 Instruction Set Attributes 0 = <CRC32>
 Instruction Set Attributes 1 = <>
         Processor Features 0 = <AdvSIMD,FP,EL3 32,EL2 32,EL1 32,EL0 32>
         Processor Features 1 = <>
      Memory Model Features 0 = <TGran4,TGran64,SNSMem,BigEnd,16bit ASID,16TB PA>
      Memory Model Features 1 = <8bit VMID>
      Memory Model Features 2 = <32bit CCIDX,48bit VA>
             Debug Features 0 = <2 CTX BKPTs,4 Watchpoints,6 Breakpoints,PMUv3,Debugv8>
             Debug Features 1 = <>
         Auxiliary Features 0 = <>
WARNING: / was not properly dismounted
         Auxiliary Features 1 = <>
CPU  1: ARM Cortex-A72 r0p3 affinity:  1
CPU  2: ARM Cortex-A72 r0p3 affinity:  2
Warning: no time-of-day clock registered, CPU  3: ARM Cortex-A72 r0p3 affinity:  3
system time will not be set accurately
WARNING: WITNESS option enabled, expect reduced performance.
uhub0: 5 ports with 4 removable, self powered
ugen0.2: <vendor 0x2109 USB2.0 Hub> at usbus0
uhub1 on uhub0
uhub1: <vendor 0x2109 USB2.0 Hub, class 9/0, rev 2.10/4.20, addr 1> on usbus0
uhub1: 4 ports with 4 removable, self powered
ugen0.3: <Generic 4-Port USB 2.0 Hub> at usbus0
uhub2 on uhub1
uhub2: <Generic 4-Port USB 2.0 Hub, class 9/0, rev 2.10/1.04, addr 2> on usbus0
uhub2: MTT enabled
uhub2: 4 ports with 4 removable, self powered
ugen0.4: <Kingston DataTraveler 3.0> at usbus0
umass0 on uhub2
umass0: <Kingston DataTraveler 3.0, class 0/0, rev 2.10/0.01, addr 3> on usbus0
umass0:  SCSI over Bulk-Only; quirks = 0xc100
umass0:0:0: Attached to scbus0
da0 at umass-sim0 bus 0 scbus0 target 0 lun 0
da0: <Kingston DataTraveler 3.0 > Removable Direct Access SPC-4 SCSI device
da0: [_SERIAL_NUMBER_XXXXXXXXXXXXXXXXXXXXX]
da0: 40.000MB/s transfers
da0: 14755MB (30218842 512 byte sectors)
da0: quirks=0x2<NO_6_BYTE>
ugen0.5: <Microsoft Natural Ergonomic Keyboard 4000> at usbus0
ukbd0 on uhub2
ukbd0: <Microsoft Natural Ergonomic Keyboard 4000, class 0/0, rev 2.00/1.73, addr 4> on usbus0
kbd1 at ukbd0
ugen0.6: <Realtek USB 10/100/1000 LAN> at usbus0
ugen0.7: <Microsoft Microsoft 5-Button Mouse with IntelliEye(TM)> at usbus0
ugen0.8: <Logitech Logitech USB Keyboard> at usbus0
ukbd1 on uhub1
ukbd1: <Logitech Logitech USB Keyboard, class 0/0, rev 1.10/12.10, addr 7> on usbus0
kbd2 at ukbd1
lo0: link state changed to UP
genet0: link state changed to DOWN
uhid0 on uhub2
uhid0: <Microsoft Natural Ergonomic Keyboard 4000, class 0/0, rev 2.00/1.73, addr 4> on usbus0
uhid1 on uhub1
uhid1: <Logitech Logitech USB Keyboard, class 0/0, rev 1.10/12.10, addr 7> on usbus0
ure0 on uhub2
ure0: <Realtek USB 10/100/1000 LAN, class 0/0, rev 2.10/30.00, addr 5> on usbus0
miibus1: <MII bus> on ure0
rgephy0: <RTL8251/8153 1000BASE-T media interface> PHY 0 on miibus1
rgephy0:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT-FDX, 1000baseT-FDX-master, auto
ue0: <USB Ethernet> on ure0
ue0: Ethernet address: [_MAC_XXXXXXXXXX]
ums0 on uhub2
ums0: <Microsoft Microsoft 5-Button Mouse with IntelliEye(TM), class 0/0, rev 1.10/3.00, addr 6> on usbus0
ums0: 5 buttons and [XYZ] coordinates ID=0
ue0: link state changed to DOWN
ue0: link state changed to UP