Launched in 2004, dmesgd aims to provide a user-submitted repository of searchable *BSD dmesgs. The dmesg(8) command displays the system message buffer's content, and during boot a copy is saved to /var/run/dmesg.boot. This buffer contains the operating system release, name and version, a list of devices identified, plus a whole host of other useful information. We hope others find this resource useful and further contribute to its growth. Contact us at [ admin at lists dot nycbug dot org ]. Note that this site is not a substitute for sending the dmesg directly to the respective project.
Date: 2020-07-09 06:53:44
From: SleepWalker
Description: PineBook Pro (FreeBSD 13.0-CURRENT) U-Boot 2020.07 EFIFB NVMe
U-Boot TPL 2020.07-rc4-dirty (Jun 16 2020 - 16:02:40)
Channel 0: LPDDR4, 50MHz
BW=32 Col=10 Bk=8 CS0 Row=15 CS1 Row=15 CS=2 Die BW=16 Size=2048MB
Channel 1: LPDDR4, 50MHz
BW=32 Col=10 Bk=8 CS0 Row=15 CS1 Row=15 CS=2 Die BW=16 Size=2048MB
256B stride
256B stride
lpddr4_set_rate: change freq to 400000000 mhz 0, 1
lpddr4_set_rate: change freq to 800000000 mhz 1, 0
Trying to boot from BOOTROM
Returning to boot ROM...
U-Boot SPL 2020.07-rc4-dirty (Jun 16 2020 - 16:02:40 +0300)
Trying to boot from MMC1
U-Boot 2020.07-rc4-dirty (Jun 16 2020 - 16:02:40 +0300)
SoC: Rockchip rk3399
Reset cause: RST
Model: Pine64 Pinebook Pro
DRAM: 3.9 GiB
PMIC: RK808
MMC: mmc@fe310000: 2, mmc@fe320000: 1, sdhci@fe330000: 0
Loading Environment from SPI Flash... SF: Detected gd25q128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB
OK
In: serial
Out: vidconsole
Err: vidconsole
Model: Pine64 Pinebook Pro
Net: No ethernet found.
** Unrecognized filesystem type **
245138 bytes read in 31 ms (7.5 MiB/s)
Scanning PCI devices on bus 0
BusDevFun VendorId DeviceId Device Class Sub-Class
_____________________________________________________________
00.00.00 0x1d87 0x0100 Bridge device 0x04
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc0(part 0) is current device
** No partition table - mmc 0 **
switch to partitions #0, OK
mmc1 is current device
Scanning mmc 1:1...
Found EFI removable media binary efi/boot/bootaa64.efi
libfdt fdt_check_header(): FDT_ERR_BADMAGIC
Card did not respond to voltage select!
Scanning disk [_EMAIL_XXXXXXX]...
Disk [_EMAIL_XXXXXXX] not ready
Scanning disk [_EMAIL_XXXXXXX]...
** Unrecognized filesystem type **
** Unrecognized filesystem type **
Scanning disk [_EMAIL_XXXXXXXXX]...
** Unrecognized filesystem type **
Found 5 disks
BootOrder not defined
EFI boot manager: Cannot load any image
108200 bytes read in 19 ms (5.4 MiB/s)
libfdt fdt_check_header(): FDT_ERR_BADMAGIC
>> FreeBSD EFI boot block
Loader path: /boot/loader.efi
Initializing modules: ZFS UFS
Load Path: /efi\boot\bootaa64.efi
Load Device: /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/SD(1)/SD(1)/HD(1,GPT,db237bbc-aa8c-11ea-b130-005056b6981b,0x8000,0x19000)
Probing 5 block devices...not supported
not supported
not supported
better
not supported
done
ZFS found no pools
UFS found 1 partition
---<<BOOT>>---
KDB: debugger backends: ddb
KDB: current backend: ddb
Copyright (c) 1992-2020 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 13.0-CURRENT #4 r361113: Wed Jun 10 20:56:14 MSK 2020
root@pinebook:/usr/src-13.0/sys/arm64/compile/PINEBOOK arm64
FreeBSD clang version 10.0.0 ([_EMAIL_XXXXX]:llvm/llvm-project.git llvmorg-10.0.0-0-gd32170dbd5b)
VT(efifb): resolution 1920x1080
Starting CPU 1 (1)
Starting CPU 2 (2)
Starting CPU 3 (3)
FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
random: unblocking device.
random: entropy device external interface
MAP f3f0c000 mode 2 pages 1
MAP f3f0f000 mode 2 pages 2
MAP f6f30000 mode 2 pages 16
WARNING: Device "kbd" is Giant locked and may be deleted before FreeBSD 13.0.
kbd0 at kbdmux0
WARNING: Device "openfirm" is Giant locked and may be deleted before FreeBSD 13.0.
ofwbus0: <Open Firmware Device Tree>
clk_fixed0: <Fixed clock> on ofwbus0
simplebus0: <Flattened device tree simple bus> on ofwbus0
rk_grf0: <RockChip General Register Files> mem 0xff320000-0xff320fff on ofwbus0
rk3399_pmucru0: <Rockchip RK3399 PMU Clock and Reset Unit> mem 0xff750000-0xff750fff on ofwbus0
rk3399_cru0: <Rockchip RK3399 Clock and Reset Unit> mem 0xff760000-0xff760fff on ofwbus0
rk_grf1: <RockChip General Register Files> mem 0xff770000-0xff77ffff on ofwbus0
regfix0: <Fixed Regulator> on ofwbus0
regfix1: <Fixed Regulator> on ofwbus0
regfix2: <Fixed Regulator> on ofwbus0
regfix3: <Fixed Regulator> on ofwbus0
regfix4: <Fixed Regulator> on ofwbus0
regfix5: <Fixed Regulator> on ofwbus0
regfix6: <Fixed Regulator> on ofwbus0
regfix7: <Fixed Regulator> on ofwbus0
regfix8: <Fixed Regulator> on ofwbus0
regfix9: <Fixed Regulator> on ofwbus0
regfix10: <Fixed Regulator> on ofwbus0
regfix11: <Fixed Regulator> on ofwbus0
simple_mfd0: <Simple MFD (Multi-Functions Device)> mem 0xff310000-0xff310fff on ofwbus0
psci0: <ARM Power State Co-ordination Interface Driver> on ofwbus0
gic0: <ARM Generic Interrupt Controller v3.0> mem 0xfee00000-0xfee0ffff,0xfef00000-0xfefbffff,0xfff00000-0xfff0ffff,0xfff10000-0xfff1ffff,0xfff20000-0xfff2ffff irq 18 on ofwbus0
its0: <ARM GIC Interrupt Translation Service> mem 0xfee20000-0xfee3ffff on gic0
rk_iodomain0: <RockChip IO Voltage Domain> mem 0-0xff31ffff,0-0xfff on rk_grf0
rk_iodomain1: <RockChip IO Voltage Domain> mem 0-0xff76ffff,0-0xffff on rk_grf1
rk_pinctrl0: <RockChip Pinctrl controller> on ofwbus0
gpio0: <RockChip GPIO Bank controller> mem 0xff720000-0xff7200ff irq 71 on rk_pinctrl0
gpiobus0: <OFW GPIO bus> on gpio0
gpio1: <RockChip GPIO Bank controller> mem 0xff730000-0xff7300ff irq 72 on rk_pinctrl0
gpiobus1: <OFW GPIO bus> on gpio1
gpio2: <RockChip GPIO Bank controller> mem 0xff780000-0xff7800ff irq 73 on rk_pinctrl0
gpiobus2: <OFW GPIO bus> on gpio2
gpio3: <RockChip GPIO Bank controller> mem 0xff788000-0xff7880ff irq 74 on rk_pinctrl0
gpiobus3: <OFW GPIO bus> on gpio3
gpio4: <RockChip GPIO Bank controller> mem 0xff790000-0xff7900ff irq 75 on rk_pinctrl0
gpiobus4: <OFW GPIO bus> on gpio4
rk_i2c0: <RockChip I2C> mem 0xff110000-0xff110fff irq 20 on ofwbus0
iicbus0: <OFW I2C bus> on rk_i2c0
rk_i2c1: <RockChip I2C> mem 0xff130000-0xff130fff irq 22 on ofwbus0
iicbus1: <OFW I2C bus> on rk_i2c1
rk_i2c2: <RockChip I2C> mem 0xff3c0000-0xff3c0fff irq 38 on ofwbus0
iicbus2: <OFW I2C bus> on rk_i2c2
syr8270: <Silergy SYR827 regulator> at addr 0x80 on iicbus2
rk_i2c3: <RockChip I2C> mem 0xff3d0000-0xff3d0fff irq 39 on ofwbus0
iicbus3: <OFW I2C bus> on rk_i2c3
rk805_pmu0: <RockChip RK805 PMIC> at addr 0x36 irq 76 on iicbus2
generic_timer0: <ARMv8 Generic Timer> irq 2,3,4,5 on ofwbus0
Timecounter "ARM MPCore Timecounter" frequency 24000000 Hz quality 1000
Event timer "ARM MPCore Eventtimer" frequency 24000000 Hz quality 1000
rk_tsadc0: <RockChip temperature sensors> mem 0xff260000-0xff2600ff irq 35 on ofwbus0
rk_usb2phy0: <Rockchip RK3399 USB2PHY> mem 0-0xff76ffff,0-0xffff on rk_grf1
rk_usb2phy1: <Rockchip RK3399 USB2PHY> mem 0-0xff76ffff,0-0xffff on rk_grf1
rk_emmcphy0: <Rockchip RK3399 eMMC PHY> mem 0-0xff76ffff,0-0xffff on rk_grf1
rk_pcie_phy0: <Rockchip RK3399 PCIe PHY> mem 0-0xff76ffff,0-0xffff on rk_grf1
rk_typec_phy0: <Rockchip RK3399 PHY TYPEC> mem 0xff7c0000-0xff7fffff on ofwbus0
rk_typec_phy1: <Rockchip RK3399 PHY TYPEC> mem 0xff800000-0xff83ffff on ofwbus0
cpulist0: <Open Firmware CPU Group> on ofwbus0
cpu0: <Open Firmware CPU> on cpulist0
cpufreq_dt0: <Generic cpufreq driver> on cpu0
cpu1: <Open Firmware CPU> on cpulist0
cpufreq_dt1: <Generic cpufreq driver> on cpu1
cpu2: <Open Firmware CPU> on cpulist0
cpufreq_dt2: <Generic cpufreq driver> on cpu2
cpu3: <Open Firmware CPU> on cpulist0
cpufreq_dt3: <Generic cpufreq driver> on cpu3
cpu4: <Open Firmware CPU> on cpulist0
cpufreq_dt4: <Generic cpufreq driver> on cpu4
cpufreq_dt4: Not attaching as cpu is not present
device_attach: cpufreq_dt4 attach returned 6
cpu5: <Open Firmware CPU> on cpulist0
cpufreq_dt5: <Generic cpufreq driver> on cpu5
cpufreq_dt5: Not attaching as cpu is not present
device_attach: cpufreq_dt5 attach returned 6
pcib0: <Rockchip PCIe controller> mem 0xf8000000-0xf9ffffff,0xfd000000-0xfdffffff irq 6,7,8 on ofwbus0
pci0: <PCI bus> on pcib0
pcib1: <PCI-PCI bridge> at device 0.0 on pci0
pcib0: failed to reserve resource for pcib1
pcib1: failed to allocate initial memory window: 0-0xfffff
pci1: <PCI bus> on pcib1
nvme0: <Generic NVMe Device> at device 0.0 on pci1
rockchip_dwmmc0: <Synopsys DesignWare Mobile Storage Host Controller (RockChip)> mem 0xfe310000-0xfe313fff irq 10 on ofwbus0
rockchip_dwmmc0: Hardware version ID is 270a
rockchip_dwmmc1: <Synopsys DesignWare Mobile Storage Host Controller (RockChip)> mem 0xfe320000-0xfe323fff irq 11 on ofwbus0
rockchip_dwmmc1: Hardware version ID is 270a
mmc0: <MMC/SD bus> on rockchip_dwmmc1
sdhci_fdt0: <Rockchip RK3399 fdt SDHCI controller> mem 0xfe330000-0xfe33ffff irq 12 on ofwbus0
rk_emmcphy0: got emmcclk clock
sdhci_fdt0-slot0: Hardware doesn't specify timeout clock frequency, setting BROKEN_TIMEOUT quirk.
sdhci_fdt0: 1 slot(s) allocated
mmc1: <MMC/SD bus> on sdhci_fdt0
ehci0: <Generic EHCI Controller> mem 0xfe380000-0xfe39ffff irq 13 on ofwbus0
usbus0: EHCI version 1.0
usbus0 on ehci0
ohci0: <Generic OHCI Controller> mem 0xfe3a0000-0xfe3bffff irq 14 on ofwbus0
usbus1 on ohci0
ehci1: <Generic EHCI Controller> mem 0xfe3c0000-0xfe3dffff irq 15 on ofwbus0
usbus2: EHCI version 1.0
usbus2 on ehci1
ohci1: <Generic OHCI Controller> mem 0xfe3e0000-0xfe3fffff irq 16 on ofwbus0
usbus3 on ohci1
rk_dwc30: <Rockchip RK3399 DWC3> on ofwbus0
xhci0: <Synopsys Designware DWC3> mem 0xfe800000-0xfe8fffff irq 82 on rk_dwc30
xhci0: 64 bytes context size, 32-bit DMA
usbus4: trying to attach
usbus4 on xhci0
rk_dwc31: <Rockchip RK3399 DWC3> on ofwbus0
xhci1: <Synopsys Designware DWC3> mem 0xfe900000-0xfe9fffff irq 83 on rk_dwc31
xhci1: 64 bytes context size, 32-bit DMA
usbus5: trying to attach
usbus5 on xhci1
iicbus0: <unknown card> at addr 0x22
iic0: <I2C generic I/O> on iicbus0
iic1: <I2C generic I/O> on iicbus1
uart0: <16750 or compatible> mem 0xff180000-0xff1800ff irq 26 on ofwbus0
uart1: <16750 or compatible> mem 0xff1a0000-0xff1a00ff irq 28 on ofwbus0
uart1: console (1500000,n,8,1)
spi0: <Rockchip SPI> mem 0xff1d0000-0xff1d0fff irq 31 on ofwbus0
spibus0: <OFW SPI bus> on spi0
mx25l0: <M25Pxx Flash Family> at cs 0 mode 0 on spibus0
mx25l0: device type gd25q128, size 16384K in 256 sectors of 64K, erase size 4K
syscon_generic0: <syscon> mem 0xffa58000-0xffa5801f on ofwbus0
syscon_generic1: <syscon> mem 0xffa5c000-0xffa5c01f on ofwbus0
syscon_generic2: <syscon> mem 0xffa60080-0xffa6009f on ofwbus0
syscon_generic3: <syscon> mem 0xffa60100-0xffa6011f on ofwbus0
syscon_generic4: <syscon> mem 0xffa60180-0xffa6019f on ofwbus0
syscon_generic5: <syscon> mem 0xffa70000-0xffa7001f on ofwbus0
syscon_generic6: <syscon> mem 0xffa70080-0xffa7009f on ofwbus0
syscon_generic7: <syscon> mem 0xffa74000-0xffa7401f on ofwbus0
syscon_generic8: <syscon> mem 0xffa76000-0xffa7601f on ofwbus0
syscon_generic9: <syscon> mem 0xffa90000-0xffa9001f on ofwbus0
syscon_generic10: <syscon> mem 0xffa98000-0xffa9801f on ofwbus0
syscon_generic11: <syscon> mem 0xffaa0000-0xffaa001f on ofwbus0
syscon_generic12: <syscon> mem 0xffaa0080-0xffaa009f on ofwbus0
syscon_generic13: <syscon> mem 0xffaa8000-0xffaa801f on ofwbus0
syscon_generic14: <syscon> mem 0xffaa8080-0xffaa809f on ofwbus0
syscon_generic15: <syscon> mem 0xffab0000-0xffab001f on ofwbus0
syscon_generic16: <syscon> mem 0xffab0080-0xffab009f on ofwbus0
syscon_generic17: <syscon> mem 0xffab8000-0xffab801f on ofwbus0
syscon_generic18: <syscon> mem 0xffac0000-0xffac001f on ofwbus0
syscon_generic19: <syscon> mem 0xffac0080-0xffac009f on ofwbus0
syscon_generic20: <syscon> mem 0xffac8000-0xffac801f on ofwbus0
syscon_generic21: <syscon> mem 0xffac8080-0xffac809f on ofwbus0
syscon_generic22: <syscon> mem 0xffad0000-0xffad001f on ofwbus0
syscon_generic23: <syscon> mem 0xffad8080-0xffad809f on ofwbus0
syscon_generic24: <syscon> mem 0xffae0000-0xffae001f on ofwbus0
iicbus2: <unknown card> at addr 0x82
iic2: <I2C generic I/O> on iicbus2
iicbus3: <unknown card> at addr 0x44
iic3: <I2C generic I/O> on iicbus3
pwm0: <Rockchip PWM> mem 0xff420000-0xff42000f on ofwbus0
pwmbus0: <OFW PWM bus> on pwm0
pwmc0: <PWM Control> channel 0 on pwmbus0
pwm1: <Rockchip PWM> mem 0xff420020-0xff42002f on ofwbus0
pwmbus1: <OFW PWM bus> on pwm1
pwmc1: <PWM Control> channel 0 on pwmbus1
gpioc0: <GPIO controller> on gpio0
gpioc1: <GPIO controller> on gpio1
gpioc2: <GPIO controller> on gpio2
gpioc3: <GPIO controller> on gpio3
gpioc4: <GPIO controller> on gpio4
gpioled0: <GPIO LEDs> on ofwbus0
syscon_generic25: <syscon> mem 0xff620000-0xff6200ff on ofwbus0
syscon_generic26: <syscon> mem 0xff330000-0xff33e3d3 on ofwbus0
cryptosoft0: <software crypto>
cpufreq_dt4: <Generic cpufreq driver> on cpu4
cpufreq_dt4: Not attaching as cpu is not present
device_attach: cpufreq_dt4 attach returned 6
cpufreq_dt5: <Generic cpufreq driver> on cpu5
cpufreq_dt5: Not attaching as cpu is not present
device_attach: cpufreq_dt5 attach returned 6
ZFS filesystem version: 5
ZFS storage pool version: features support (5000)
Timecounters tick every 1.000 msec
ipfw2 (+ipv6) initialized, divert enabled, nat enabled, default to accept, logging usbus0: 480Mbps High Speed USB v2.0
usbus1: 12Mbps Full Speed USB v1.0
disabled
Obsolete code will be removed soon: random(9) is the obsolete Park-Miller LCG from 1988
ugen1.1: <Generic OHCI root HUB> at usbus1
ugen0.1: <Generic EHCI root HUB> at usbus0
uhub0 on usbus0
uhub0: <Generic EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus0
uhub1 on usbus1
uhub1: <Generic OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
usbus2: 480Mbps High Speed USB v2.0
usbus3: 12Mbps Full Speed USB v1.0
ugen2.1: <Generic EHCI root HUB> at usbus2
uhub2 on usbus2
uhub2: <Generic EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus2
ugen3.1: <Generic OHCI root HUB> at usbus3
uhub3 on usbus3
uhub3: <Generic OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus3
usbus4: 5.0Gbps Super Speed USB v3.0
usbus5: 5.0Gbps Super Speed USB v3.0
ugen4.1: <Synopsys XHCI root HUB> at usbus4
uhub4 on usbus4
uhub4: <Synopsys XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus4
ugen5.1: <Synopsys XHCI root HUB> at usbus5
uhub5 on usbus5
uhub5: <Synopsys XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus5
uhub1: 1 port with 1 removable, self powered
nvme0: Allocated 64MB host memory buffer
uhub3: 1 port with 1 removable, self powered
mmcsd0: 8GB <SDHC SA08G 8.0 SN DCD888E1 MFG 08/2018 by 3 SD> at mmc0 20.0MHz/4bit/2048-block
uhub4: 2 ports with 2 removable, self powered
uhub0: 1 port with 1 removable, self powered
uhub5: 2 ports with 2 removable, self powered
mmcsd1: 63GB <MMCHC DA4064 0.1 SN E35AEF0E MFG 07/2019 by 69 0x0000> at mmc1 25.0MHz/8bit/65535-block
mmcsd1boot0: 4MB partition 1 at mmcsd1
mmcsd1boot1: 4MB partition 2 at mmcsd1
mmcsd1rpmb: 17MB partition 3 at mmcsd1
Release APs...done
CPU 0: ARM Cortex-A53 r0p4 affinity: 0
Cache Type = <64 byte D-cacheline,64 byte I-cacheline,VIPT ICache,64 byte ERG,64 byte CWG>
nda0 at nvme0 bus 0 scbus1 target 0 lun 1
Instruction Set Attributes 0 = <CRC32,SHA2,SHA1,AES+PMULL>
Trying to mount root from zfs:freenas-boot/ROOT/pinebook []...
nda0: Instruction Set Attributes 1 = <>
<NE-256 S0620A 9100407606414>
Processor Features 0 = <GIC,AdvSIMD,FP,EL3 32,EL2 32,EL1 32,EL0 32>
nda0: nvme version 1.3 x4 (max x4) lanes PCIe Gen2 (max Gen3) link
Processor Features 1 = <>
nda0: 244198MB (500118192 512 byte sectors)
Memory Model Features 0 = <TGran4,TGran64,SNSMem,BigEnd,16bit ASID,1TB PA>
Memory Model Features 1 = <8bit VMID>
Memory Model Features 2 = <32bit CCIDX,48bit VA>
Debug Features 0 = <2 CTX BKPTs,4 Watchpoints,6 Breakpoints,PMUv3,Debugv8>
Debug Features 1 = <>
Auxiliary Features 0 = <>
Auxiliary Features 1 = <>
CPU 1: ARM Cortex-A53 r0p4 affinity: 1
CPU 2: ARM Cortex-A53 r0p4 affinity: 2
CPU 3: ARM Cortex-A53 r0p4 affinity: 3
Unresolved linked clock found: clkin_gmac
uhub2: 1 port with 1 removable, self powered
GEOM: mmcsd1: the primary GPT table is corrupt or invalid.
GEOM: mmcsd1: using the secondary instead -- recovery strongly advised.
GEOM: diskid/DISK-E35AEF0E: the primary GPT table is corrupt or invalid.
GEOM: diskid/DISK-E35AEF0E: using the secondary instead -- recovery strongly advised.
Root mount waiting for: usbus2
ugen2.2: <vendor 0x05e3 USB2.0 Hub> at usbus2
uhub6 on uhub2
uhub6: <vendor 0x05e3 USB2.0 Hub, class 9/0, rev 2.00/85.36, addr 2> on usbus2
ugen1.2: <HAILUCK CO.,LTD USB KEYBOARD> at usbus1
ukbd0 on uhub1
ukbd0: <HAILUCK CO.,LTD USB KEYBOARD, class 0/0, rev 1.10/1.00, addr 2> on usbus1
kbd1 at ukbd0
Root mount waiting for: usbus2
uhub6: 4 ports with 4 removable, self powered
ugen2.3: <Sonix Technology Co., Ltd. USB Camera> at usbus2
Warning: no time-of-day clock registered, system time will not be set accurately
Setting hostuuid: 66316338-3065-3865-3763-386439343964.
Setting hostid: 0xd83349b9.
Starting file system checks:
Mounting local filesystems:.
ELF ldconfig path: /lib /usr/lib /usr/lib/compat /usr/local/lib /usr/local/lib/compat/pkg /usr/local/lib/compat/pkg /usr/local/lib/perl5/5.30/mach/CORE
Setting hostname: pinebook-pro.
Setting up harvesting: [UMA],[FS_ATIME],SWI,INTERRUPT,NET_NG,[NET_ETHER],NET_TUN,MOUSE,KEYBOARD,ATTACH,CACHED
Feeding entropy: .
ifconfig: SIOCIFCREATE2: Device not configured
lo0: link state changed to UP
Starting Network: lo0.
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384
options=680003<RXCSUM,TXCSUM,LINKSTATE,RXCSUM_IPV6,TXCSUM_IPV6>
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x1
inet[_IP_XXXX] netmask 0xff000000
groups: lo
nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
Starting devd.
Autoloading module: uhid.ko
Autoloading module: wmt.ko
Autoloading module: uhid.ko
Autoloading module: wmt.ko
add host[_IP_XXXX]: gateway lo0 fib 0: route already in table
add host ::1: gateway lo0 fib 0: route already in table
add net fe80::: gateway ::1
add net ff02::: gateway ::1
add net ::ffff:0.0.0.0: gateway ::1
add net ::0.0.0.0: gateway ::1
Creating and/or trimming log files.
Starting syslogd.
No core dumps found.
Setting date via ntp.
Clearing /tmp (X related).
Starting local daemons:
.
Updating motd:.
Mounting late filesystems:.
Updating /var/run/os-release done.
Starting powerd.
Configuring vt: blanktime.
Performing sanity check on sshd configuration.
Starting sshd.
Starting cron.
Starting background file system checks in 60 seconds.
Thu Jan 1 03:00:16 MSK 1970
FreeBSD/arm64 (pinebook-pro) (ttyu1)
login: