Launched in 2004, dmesgd aims to provide a user-submitted repository of searchable *BSD dmesgs. The dmesg(8) command displays the system message buffer's content, and during boot a copy is saved to /var/run/dmesg.boot. This buffer contains the operating system release, name and version, a list of devices identified, plus a whole host of other useful information. We hope others find this resource useful and further contribute to its growth. Contact us at [ admin at lists dot nycbug dot org ]. Note that this site is not a substitute for sending the dmesg directly to the respective project.


Date: 2020-12-27 19:54:28
From: petr
Description: FreeBSD/arm64 on raspberrypi rpi
---<<BOOT>>---
Copyright (c) 1992-2020 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 12.2-RELEASE r366954 GENERIC arm64
FreeBSD clang version 10.0.1 ([_EMAIL_XXXXX]:llvm/llvm-project.git llvmorg-10.0.1-0-gef32c611aa2)
VT(efifb): resolution 656x416
KLD file umodem.ko is missing dependencies
real memory  = 993849344 (947 MB)
avail memory = 950001664 (905 MB)
Starting CPU 1 (1)
Starting CPU 2 (2)
Starting CPU 3 (3)
FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
arc4random: no preloaded entropy cache
random: entropy device external interface
MAP 39f3f000 mode 2 pages 1
MAP 39f45000 mode 2 pages 2
MAP 3b350000 mode 2 pages 16
MAP 3f100000 mode 0 pages 1
kbd0 at kbdmux0
ofwbus0: <Open Firmware Device Tree>
simplebus0: <Flattened device tree simple bus> on ofwbus0
ofw_clkbus0: <OFW clocks bus> on ofwbus0
clk_fixed0: <Fixed clock> on ofw_clkbus0
clk_fixed1: <Fixed clock> on ofw_clkbus0
regfix0: <Fixed Regulator> on ofwbus0
regfix1: <Fixed Regulator> on ofwbus0
psci0: <ARM Power State Co-ordination Interface Driver> on ofwbus0
lintc0: <BCM2836 Interrupt Controller> mem 0x40000000-0x400000ff on simplebus0
intc0: <BCM2835 Interrupt Controller> mem 0x7e00b200-0x7e00b3ff irq 48 on simplebus0
gpio0: <BCM2708/2835 GPIO controller> mem 0x7e200000-0x7e2000b3 irq 24,25 on simplebus0
gpiobus0: <OFW GPIO bus> on gpio0
generic_timer0: <ARMv7 Generic Timer> irq 1,2,3,4 on ofwbus0
Timecounter "ARM MPCore Timecounter" frequency 19200000 Hz quality 1000
Event timer "ARM MPCore Eventtimer" frequency 19200000 Hz quality 1000
usb_nop_xceiv0: <USB NOP PHY> on ofwbus0
bcm_dma0: <BCM2835 DMA Controller> mem 0x7e007000-0x7e007eff irq 6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21 on simplebus0
bcmwd0: <BCM2708/2835 Watchdog> mem 0x7e100000-0x7e100113,0x7e00a000-0x7e00a023 on simplebus0
bcm2835_clkman0: <BCM283x Clock Manager> mem 0x7e101000-0x7e102fff on simplebus0
bcmrng0: <Broadcom BCM2835 RNG> mem 0x7e104000-0x7e10400f irq 22 on simplebus0
mbox0: <BCM2835 VideoCore Mailbox> mem 0x7e00b880-0x7e00b8bf irq 23 on simplebus0
gpioc0: <GPIO controller> on gpio0
uart0: <PrimeCell UART (PL011)> mem 0x7e201000-0x7e2011ff irq 26 on simplebus0
uart0: console (115200,n,8,1)
spi0: <BCM2708/2835 SPI controller> mem 0x7e204000-0x7e2041ff irq 28 on simplebus0
spibus0: <OFW SPI bus> on spi0
spibus0: <unknown card> at cs 0 mode 0
spibus0: <unknown card> at cs 1 mode 0
iichb0: <BCM2708/2835 BSC controller> mem 0x7e804000-0x7e804fff irq 40 on simplebus0
bcm283x_dwcotg0: <DWC OTG 2.0 integrated USB controller (bcm283x)> mem 0x7e980000-0x7e98ffff,0x7e006000-0x7e006fff irq 46,47 on simplebus0
usbus0 on bcm283x_dwcotg0
sdhci_bcm0: <Broadcom 2708 SDHCI controller> mem 0x7e300000-0x7e3000ff irq 50 on simplebus0
mmc0: <MMC/SD bus> on sdhci_bcm0
fb0: <BCM2835 VT framebuffer driver> on simplebus0
fb0: keeping existing fb bpp of 32
fbd0 on fb0
VT: Replacing driver "efifb" with new "fb".
fb0: 656x416(656x416@0,0) 32bpp
fb0: fbswap: 1, pitch 2624, base 0x3eaf0000, screen_size 1091584
pmu0: <Performance Monitoring Unit> irq 0 on ofwbus0
cpulist0: <Open Firmware CPU Group> on ofwbus0
cpu0: <Open Firmware CPU> on cpulist0
bcm2835_cpufreq0: <CPU Frequency Control> on cpu0
cpu1: <Open Firmware CPU> on cpulist0
cpu2: <Open Firmware CPU> on cpulist0
cpu3: <Open Firmware CPU> on cpulist0
gpioled0: <GPIO LEDs> on ofwbus0
gpioled0: <led0> failed to map pin
gpioled0: <led1> failed to map pin
cryptosoft0: <software crypto>
Timecounters tick every 1.000 msec
iicbus0: <OFW I2C bus> on iichb0
iic0: <I2C generic I/O> on iicbus0
usbus0: 480Mbps High Speed USB v2.0
ugen0.1: <DWCOTG OTG Root HUB> at usbus0
uhub0: <DWCOTG OTG Root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus0
mmcsd0: 32GB <SDHC SP32G 8.0 SN B3294A3E MFG 07/2018 by 3 SD> at mmc0 50.0MHz/4bit/65535-block
mbox0: mbox response error
bcm2835_cpufreq0: can't get clock rate (id=8)
bcm2835_cpufreq0: ARM 600MHz, Core 250MHz, SDRAM -999MHz, Turbo OFF
Release APs...done
CPU  0: ARM Cortex-A53 r0p4 affinity:  0
arc4random: no preloaded entropy cache
 Instruction Set Attributes 0 = <CRC32>
Trying to mount root from ufs:/dev/ufs/rootfs [rw]...
 Instruction Set Attributes 1 = <>
         Processor Features 0 = <AdvSIMD,Float,EL3 32,EL2 32,EL1 32,EL0 32>
         Processor Features 1 = <0>
      Memory Model Features 0 = <4k Granule,64k Granule,S/NS Mem,MixedEndian,16bit ASID,1TB PA>
      Memory Model Features 1 = <>
      Memory Model Features 2 = <32b CCIDX,48b VA>
             Debug Features 0 = <2 CTX Breakpoints,4 Watchpoints,6 Breakpoints,PMUv3,Debug v8>
             Debug Features 1 = <0>
         Auxiliary Features 0 = <0>
         Auxiliary Features 1 = <0>
CPU  1: ARM Cortex-A53 r0p4 affinity:  1
CPU  2: ARM Cortex-A53 r0p4 affinity:  2
CPU  3: ARM Cortex-A53 r0p4 affinity:  3
Warning: no time-of-day clock registered, system time will not be set accurately
arc4random: no preloaded entropy cache
uhub0: 1 port with 1 removable, self powered
arc4random: no preloaded entropy cache
random: read_random_uio unblock wait
ugen0.2: <vendor 0x0424 product 0x9514> at usbus0
uhub1 on uhub0
uhub1: <vendor 0x0424 product 0x9514, class 9/0, rev 2.00/2.00, addr 2> on usbus0
uhub1: MTT enabled
uhub1: 5 ports with 4 removable, self powered
random: unblocking device.
GEOM_PART: mmcsd0s2 was automatically resized.
  Use `gpart commit mmcsd0s2` to save changes or `gpart undo mmcsd0s2` to revert them.
ugen0.3: <vendor 0x0424 product 0xec00> at usbus0
smsc0 on uhub1
smsc0: <vendor 0x0424 product 0xec00, rev 2.00/2.00, addr 3> on usbus0
smsc0: chip 0xec00, rev. 0002
miibus0: <MII bus> on smsc0
smscphy0: <SMC LAN8700 10/100 interface> PHY 1 on miibus0
smscphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
ue0: <USB Ethernet> on smsc0
ue0: Ethernet address: [_MAC_XXXXXXXXXX]
lo0: link state changed to UP
smsc0: chip 0xec00, rev. 0002
ue0: link state changed to DOWN
ue0: link state changed to UP