Launched in 2004, dmesgd aims to provide a user-submitted repository of searchable *BSD dmesgs. The dmesg(8) command displays the system message buffer's content, and during boot a copy is saved to /var/run/dmesg.boot. This buffer contains the operating system release, name and version, a list of devices identified, plus a whole host of other useful information. We hope others find this resource useful and further contribute to its growth. Contact us at [ admin at lists dot nycbug dot org ]. Note that this site is not a substitute for sending the dmesg directly to the respective project.
Date: 2023-03-12 14:55:25
From: mmarc
Description: NanoPi Neo3 RK3328
U-Boot TPL 2023.01-rc4 (Jan 03 2023 - 11:10:10) [192/1826]
DDR4, 333MHz
BW=32 Col=10 Bk=4 BG=2 CS0 Row=16 CS=1 Die BW=16 Size=2048MB
Trying to boot from BOOTROM
Returning to boot ROM...
Running in level: 3
U-Boot SPL 2023.01-rc4 (Jan 03 2023 - 11:10:10 +0100)
rockchip_spi_of_to_plat: base=ff190000, max-frequency=50000000, deactivate_delay=0
rockchip_spi_probe: probe
rockchip_spi_probe: rate = 750000
Trying to boot from SPI
NOTICE: BL31: v2.3():v2.3-dirty
NOTICE: BL31: Built : 11:04:37, Jan 3 2023
NOTICE: BL31:Rockchip release version: v1.2
ns16550_serial serial@ff130000: pinctrl_select_state_full: uclass_get_device_by_phandle_id: err=-19
U-Boot 2023.01-rc4 (Jan 03 2023 - 11:10:12 +0100)
Model: FriendlyElec NanoPi R2S
DRAM: 2 GiB
PMIC: RK8050 (on=0x40, off=0x00)
Core: 235 devices, 25 uclasses, devicetree: separate
MMC: mmc@ff500000: 1
Loading Environment from SPIFlash... rockchip_spi_of_to_plat: base=ff190000, max-frequency=50000000, deactivate_delay=0
rockchip_spi_probe: probe
rockchip_spi_probe: rate = 750000
SF: Detected w25q128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB
OK
In: serial@ff130000
Out: serial@ff130000
Err: serial@ff130000
Model: FriendlyElec NanoPi R2S
EFUSE
Net: eth0: ethernet@ff540000
Hit any key to stop autoboot: 0
=> tftp 0x200000 rk3328-rock64.dtb [155/1826]
ethernet@ff540000 Waiting for PHY auto negotiation to complete..... done
Speed: 1000, full duplex
Using ethernet@ff540000 device
TFTP from server[_IP_XXXX]; our IP address is[_IP_XXXXXX]
Filename 'rk3328-rock64.dtb'.
Load address: 0x200000
Loading: ####
3.2 MiB/s
done
Bytes transferred = 50576 (c590 hex)
=> tftp 0x300000 kernel.bin
Speed: 1000, full duplex
Using ethernet@ff540000 device
TFTP from server[_IP_XXXX]; our IP address is[_IP_XXXXXX]
Filename 'kernel.bin'.
Load address: 0x300000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#######################################
3.8 MiB/s
done
Bytes transferred = 12969664 (c5e6c0 hex)
=> booti 0x300000 - 0x200000
Moving Image from 0x300000 to 0x400000, end=13e0000
## Flattened Device Tree blob at 00200000
Booting using the fdt blob at 0x200000
Working FDT set to 200000
Loading Device Tree to 000000007df19000, end 000000007df2858f ... OK
Working FDT set to 7df19000
[114/1826]
Starting kernel ...
---<<BOOT>>---
Copyright (c) 1992-2021 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 13.1-RELEASE releng/13.1-n250148-fc952ac2212 GENERIC arm64
FreeBSD clang version 13.0.0 ([_EMAIL_XXXXX]:llvm/llvm-project.git llvmorg-13.0.0-0-gd7b669b3a303)
VT: init without driver.
module firmware already present!
real memory = 2145386496 (2046 MB)
avail memory = 2072510464 (1976 MB)
Starting CPU 1 (1)
Starting CPU 2 (2)
Starting CPU 3 (3)
FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
arc4random: WARNING: initial seeding bypassed the cryptographic random device because it was not yet seeded and the knob 'bypass_before_seeding' was enabled.
random: entropy device external interface
kbd0 at kbdmux0
ofwbus0: <Open Firmware Device Tree>
simplebus0: <Flattened device tree simple bus> on ofwbus0
clk_fixed0: <Fixed clock> on ofwbus0
rk_grf0: <RockChip General Register Files> mem 0xff100000-0xff100fff on ofwbus0
rk3328_cru0: <Rockchip RK3328 Clock and Reset Unit> mem 0xff440000-0xff440fff on ofwbus0
Cannot set frequency for clk: aclk_bus_pre, error: 34
rk3328_cru0: Failed to set aclk_bus_pre to a frequency of 15000000
Cannot set frequency for clk: aclk_peri_pre, error: 34
rk3328_cru0: Failed to set aclk_peri_pre to a frequency of 15000000
clk_fixed1: <Fixed clock> on ofwbus0
regfix0: <Fixed Regulator> on ofwbus0
regfix1: <Fixed Regulator> on ofwbus0
regfix2: <Fixed Regulator> on ofwbus0
regfix3: <Fixed Regulator> on ofwbus0
simple_mfd0: <Simple MFD (Multi-Functions Device)> mem 0xff450000-0xff45ffff on ofwbus0
psci0: <ARM Power State Co-ordination Interface Driver> on ofwbus0
gic0: <ARM Generic Interrupt Controller> mem 0xff811000-0xff811fff,0xff812000-0xff813fff,0xff814000-0xff815fff,0xff816000-0xff817fff irq 49 on ofwbus0
gic0: pn 0x2, arch 0x2, rev 0x1, implementer 0x43b irqs 160
rk_pinctrl0: <RockChip Pinctrl controller> on ofwbus0
gpio0: <RockChip GPIO Bank controller> mem 0xff210000-0xff2100ff irq 52 on rk_pinctrl0
gpiobus0: <OFW GPIO bus> on gpio0
gpio1: <RockChip GPIO Bank controller> mem 0xff220000-0xff2200ff irq 53 on rk_pinctrl0 [72/1826]
gpiobus1: <OFW GPIO bus> on gpio1
gpio2: <RockChip GPIO Bank controller> mem 0xff230000-0xff2300ff irq 54 on rk_pinctrl0
gpiobus2: <OFW GPIO bus> on gpio2
gpio3: <RockChip GPIO Bank controller> mem 0xff240000-0xff2400ff irq 55 on rk_pinctrl0
gpiobus3: <OFW GPIO bus> on gpio3
rk_i2c0: <RockChip I2C> mem 0xff160000-0xff160fff irq 16 on ofwbus0
iicbus0: <OFW I2C bus> on rk_i2c0
rk805_pmu0: <RockChip RK805 PMIC> at addr 0x30 irq 56 on iicbus0
generic_timer0: <ARMv8 Generic Timer> irq 4,5,6,7 on ofwbus0
Timecounter "ARM MPCore Timecounter" frequency 24000000 Hz quality 1000
Event timer "ARM MPCore Eventtimer" frequency 24000000 Hz quality 1000
rk_tsadc0: <RockChip temperature sensors> mem 0xff250000-0xff2500ff irq 22 on ofwbus0
cpulist0: <Open Firmware CPU Group> on ofwbus0
cpu0: <Open Firmware CPU> on cpulist0
cpufreq_dt0: <Generic cpufreq driver> on cpu0
cpu1: <Open Firmware CPU> on cpulist0
cpufreq_dt1: <Generic cpufreq driver> on cpu1
cpu2: <Open Firmware CPU> on cpulist0
cpufreq_dt2: <Generic cpufreq driver> on cpu2
cpu3: <Open Firmware CPU> on cpulist0
cpufreq_dt3: <Generic cpufreq driver> on cpu3
pmu0: <Performance Monitoring Unit> irq 0,1,2,3 on ofwbus0
uart0: <16750 or compatible> mem 0xff130000-0xff1300ff irq 14 on ofwbus0
uart0: console (-1,n,8,1)
iic0: <I2C generic I/O> on iicbus0
spi0: <Rockchip SPI> mem 0xff190000-0xff190fff irq 19 on ofwbus0
spi0: cannot get apb_pclk clock
device_attach: spi0 attach returned 6
rockchip_dwmmc0: <Synopsys DesignWare Mobile Storage Host Controller (RockChip)> mem 0xff500000-0xff503fff irq 41 on ofwbus0
rockchip_dwmmc0: Hardware version ID is 270a
rockchip_dwmmc1: <Synopsys DesignWare Mobile Storage Host Controller (RockChip)> mem 0xff520000-0xff523fff irq 43 on ofwbus0
rockchip_dwmmc1: Hardware version ID is 270a
mmc0: <MMC/SD bus> on rockchip_dwmmc1
dwc0: <Rockchip Gigabit Ethernet Controller> mem 0xff540000-0xff54ffff irq 44 on ofwbus0
miibus0: <MII bus> on dwc0
rgephy0: <RTL8169S/8110S/8211 1000BASE-T media interface> PHY 0 on miibus0
rgephy0: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
rgephy1: <RTL8169S/8110S/8211 1000BASE-T media interface> PHY 1 on miibus0
rgephy1: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
dwc0: Ethernet address: [_MAC_XXXXXXXXXX]
dwcotg0: <DWC OTG 2.0 integrated USB controller> mem 0xff580000-0xff5bffff irq 46 on ofwbus0
usbus1 on dwcotg0 [30/1826]
ehci0: <Generic EHCI Controller> mem 0xff5c0000-0xff5cffff irq 47 on ofwbus0
usbus2: EHCI version 1.0
usbus2 on ehci0
ohci0: <Generic OHCI Controller> mem 0xff5d0000-0xff5dffff irq 48 on ofwbus0
usbus3 on ohci0
gpioc0: <GPIO controller> on gpio0
gpioc1: <GPIO controller> on gpio1
gpioc2: <GPIO controller> on gpio2
gpioc3: <GPIO controller> on gpio3
gpioled0: <GPIO LEDs> on ofwbus0
gpioled0: <led-0> failed to map pin
gpioled0: <led-1> failed to map pin
armv8crypto0: <AES-CBC,AES-XTS,AES-GCM>
Timecounters tick every 1.000 msec
rk805_pmu0: registered as a time-of-day clock, resolution 1.000000s
usbus1: 480Mbps High Speed USB v2.0
usbus2: 480Mbps High Speed USB v2.0
usbus3: 12Mbps Full Speed USB v1.0
ugen3.1: <Generic OHCI root HUB> at usbus3
uhub0 on usbus3
uhub0: <Generic OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus3
ugen2.1: <Generic EHCI root HUB> at usbus2
uhub1 on usbus2
uhub1: <Generic EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus2
ugen1.1: <DWCOTG OTG Root HUB> at usbus1
uhub2 on usbus1
uhub2: <DWCOTG OTG Root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1
mmc0: No compatible cards found on bus
CPU 0: ARM Cortex-A53 r0p4 affinity: 0
Cache Type = <64 byte D-cacheline,64 byte I-cacheline,VIPT ICache,64 byte ERG,64 byte CWG>
Instruction Set Attributes 0 = <CRC32,SHA2,SHA1,AES+PMULL>
Instruction Set Attributes 1 = <>
Processor Features 0 = <AdvSIMD,FP,EL3 32,EL2 32,EL1 32,EL0 32>
Processor Features 1 = <>
Memory Model Features 0 = <TGran4,TGran64,SNSMem,BigEnd,16bit ASID,1TB PA>
Memory Model Features 1 = <8bit VMID>
Memory Model Features 2 = <32bit CCIDX,48bit VA>
Debug Features 0 = <DoubleLock,2 CTX BKPTs,4 Watchpoints,6 Breakpoints,PMUv3,Debugv8>
Debug Features 1 = <>
Auxiliary Features 0 = <>
Auxiliary Features 1 = <>
AArch32 Instruction Set Attributes 5 = <CRC32,SHA2,SHA1,AES+VMULL,SEVL>
AArch32 Media and VFP Features 0 = <FPRound,FPSqrt,FPDivide,DP VFPv3+v4,SP VFPv3+v4,AdvSIMD>
AArch32 Media and VFP Features 1 = <SIMDFMAC,FPHP DP Conv,SIMDHP SP Conv,SIMDSP,SIMDInt,SIMDLS,FPDNaN,FPFtZ>
CPU 1: ARM Cortex-A53 r0p4 affinity: 1
CPU 2: ARM Cortex-A53 r0p4 affinity: 2
CPU 3: ARM Cortex-A53 r0p4 affinity: 3
Release APs...done
uhub0: 1 port with 1 removable, self powered
uhub2: 1 port with 1 removable, self powered
uhub1: 1 port with 1 removable, self powered
Loader variables:
Manual root filesystem specification:
<fstype>:<device> [options]
Mount <device> using filesystem <fstype>
and with the specified (optional) option list.
eg. ufs:/dev/da0s1a
zfs:zroot/ROOT/default
cd9660:/dev/cd0 ro
(which is equivalent to: mount -t cd9660 -o ro /dev/cd0 /)
? List valid disk boot devices
. Yield 1 second (for background tasks)
<empty line> Abort manual input
mountroot> random: unblocking device.