Launched in 2004, dmesgd aims to provide a user-submitted repository of searchable *BSD dmesgs. The dmesg(8) command displays the system message buffer's content, and during boot a copy is saved to /var/run/dmesg.boot. This buffer contains the operating system release, name and version, a list of devices identified, plus a whole host of other useful information. We hope others find this resource useful and further contribute to its growth. Contact us at [ admin at lists dot nycbug dot org ]. Note that this site is not a substitute for sending the dmesg directly to the respective project.
Date: 2023-04-21 14:15:19
From: csoki
Description: FreeBSD/arm64 on raspberrypi rpi
WARNING: Cannot find freebsd,dts-version property, cannot check DTB compliance
Copyright (c) 1992-2021 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 13.1-RELEASE-p6 GENERIC arm64
FreeBSD clang version 13.0.0 ([_EMAIL_XXXXX]:llvm/llvm-project.git llvmorg-13.0.0-0-gd7b669b3a303)
VT(efifb): resolution 656x416
module firmware already present!
real memory = 993841152 (947 MB)
avail memory = 946745344 (902 MB)
Starting CPU 1 (1)
Starting CPU 2 (2)
Starting CPU 3 (3)
FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
random: unblocking device.
random: entropy device external interface
MAP 39f3d000 mode 2 pages 1
MAP 39f41000 mode 2 pages 3
MAP 39f45000 mode 2 pages 4
MAP 3b350000 mode 2 pages 16
MAP 3f100000 mode 0 pages 1
kbd0 at kbdmux0
ofwbus0: <Open Firmware Device Tree>
simplebus0: <Flattened device tree simple bus> on ofwbus0
ofw_clkbus0: <OFW clocks bus> on ofwbus0
clk_fixed0: <Fixed clock> on ofw_clkbus0
clk_fixed1: <Fixed clock> on ofw_clkbus0
regfix0: <Fixed Regulator> on ofwbus0
regfix1: <Fixed Regulator> on ofwbus0
bcm2835_firmware0: <BCM2835 Firmware> on simplebus0
ofw_clkbus1: <OFW clocks bus> on bcm2835_firmware0
psci0: <ARM Power State Co-ordination Interface Driver> on ofwbus0
lintc0: <BCM2836 Interrupt Controller> mem 0x40000000-0x400000ff on simplebus0
intc0: <BCM2835 Interrupt Controller> mem 0x7e00b200-0x7e00b3ff irq 39 on simplebus0
gpio0: <BCM2708/2835 GPIO controller> mem 0x7e200000-0x7e2000b3 irq 7,8 on simplebus0
gpiobus0: <OFW GPIO bus> on gpio0
gpio1: <Raspberry Pi Firmware GPIO controller> on bcm2835_firmware0
gpiobus1: <GPIO bus> on gpio1
mbox0: <BCM2835 VideoCore Mailbox> mem 0x7e00b880-0x7e00b8bf irq 6 on simplebus0
generic_timer0: <ARMv7 Generic Timer> irq 1,2,3,4 on ofwbus0
Timecounter "ARM MPCore Timecounter" frequency 19200000 Hz quality 1000
Event timer "ARM MPCore Eventtimer" frequency 19200000 Hz quality 1000
usb_nop_xceiv0: <USB NOP PHY> on ofwbus0
bcm2835_clkman0: <BCM283x Clock Manager> mem 0x7e101000-0x7e102fff on simplebus0
gpioc0: <GPIO controller> on gpio0
uart0: <PrimeCell UART (PL011)> mem 0x7e201000-0x7e2011ff irq 9 on simplebus0
uart0: console (115200,n,8,1)
spi0: <BCM2708/2835 SPI controller> mem 0x7e204000-0x7e2041ff irq 11 on simplebus0
spibus0: <OFW SPI bus> on spi0
spibus0: <unknown card> at cs 0 mode 0
spibus0: <unknown card> at cs 1 mode 0
iichb0: <BCM2708/2835 BSC controller> mem 0x7e804000-0x7e804fff irq 19 on simplebus0
bcm283x_dwcotg0: <DWC OTG 2.0 integrated USB controller (bcm283x)> mem 0x7e980000-0x7e98ffff,0x7e006000-0x7e006fff irq 21,22 on simplebus0
usbus1 on bcm283x_dwcotg0
bcm_dma0: <BCM2835 DMA Controller> mem 0x7e007000-0x7e007eff irq 23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38 on simplebus0
bcmwd0: <BCM2708/2835 Watchdog> mem 0x7e100000-0x7e100113,0x7e00a000-0x7e00a023 on simplebus0
bcmrng0: <Broadcom BCM2835/BCM2838 RNG> mem 0x7e104000-0x7e10400f irq 40 on simplebus0
sdhci_bcm0: <Broadcom 2708 SDHCI controller> mem 0x7e300000-0x7e3000ff irq 48 on simplebus0
mmc0: <MMC/SD bus> on sdhci_bcm0
gpioc1: <GPIO controller> on gpio1
fb0: <BCM2835 VT framebuffer driver> on simplebus0
fb0: keeping existing fb bpp of 32
fbd0 on fb0
WARNING: Device "fb" is Giant locked and may be deleted before FreeBSD 14.0.
VT: Replacing driver "efifb" with new "fb".
fb0: 656x416(656x416@0,0) 32bpp
fb0: fbswap: 1, pitch 2624, base 0x3eaf0000, screen_size 1091584
pmu0: <Performance Monitoring Unit> irq 0 on ofwbus0
cpulist0: <Open Firmware CPU Group> on ofwbus0
cpu0: <Open Firmware CPU> on cpulist0
bcm2835_cpufreq0: <CPU Frequency Control> on cpu0
cpu1: <Open Firmware CPU> on cpulist0
cpu2: <Open Firmware CPU> on cpulist0
cpu3: <Open Firmware CPU> on cpulist0
gpioled0: <GPIO LEDs> on ofwbus0
gpioled0: <led0> failed to map pin
armv8crypto0: CPU lacks AES instructions
Timecounters tick every 1.000 msec
iicbus0: <OFW I2C bus> on iichb0
iic0: <I2C generic I/O> on iicbus0
usbus1: 480Mbps High Speed USB v2.0
ugen1.1: <DWCOTG OTG Root HUB> at usbus1
uhub0 on usbus1
uhub0: <DWCOTG OTG Root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1
mmcsd0: 32GB <SDHC SC32G 8.0 SN 3A784A9A MFG 02/2018 by 3 SD> at mmc0 50.0MHz/4bit/65535-block
bcm2835_cpufreq0: ARM 600MHz, Core 250MHz, SDRAM 400MHz, Turbo OFF
CPU 0: ARM Cortex-A53 r0p4 affinity: 0
Cache Type = <64 byte D-cacheline,64 byte I-cacheline,VIPT ICache,64 byte ERG,64 byte CWG>
Instruction Set Attributes 0 = <CRC32>
Instruction Set Attributes 1 = <>
Processor Features 0 = <AdvSIMD,FP,EL3 32,EL2 32,EL1 32,EL0 32>
Processor Features 1 = <>
Memory Model Features 0 = <TGran4,TGran64,SNSMem,BigEnd,16bit ASID,1TB PA>
Trying to mount root from ufs:/dev/ufs/rootfs [rw]...
Memory Model Features 1 = <8bit VMID>
Memory Model Features 2 = <32bit CCIDX,48bit VA>
Debug Features 0 = <DoubleLock,2 CTX BKPTs,4 Watchpoints,6 Breakpoints,PMUv3,Debugv8>
Debug Features 1 = <>
Auxiliary Features 0 = <>
Auxiliary Features 1 = <>
AArch32 Instruction Set Attributes 5 = <CRC32,SEVL>
AArch32 Media and VFP Features 0 = <FPRound,FPSqrt,FPDivide,DP VFPv3+v4,SP VFPv3+v4,AdvSIMD>
AArch32 Media and VFP Features 1 = <SIMDFMAC,FPHP DP Conv,SIMDHP SP Conv,SIMDSP,SIMDInt,SIMDLS,FPDNaN,FPFtZ>
CPU 1: ARM Cortex-A53 r0p4 affinity: 1
CPU 2: ARM Cortex-A53 r0p4 affinity: 2
CPU 3: ARM Cortex-A53 r0p4 affinity: 3
Release APs...done
Warning: no time-of-day clock registered, system time will not be set accurately
Dual Console: Serial Primary, Video Secondary
uhub0: 1 port with 1 removable, self powered
ugen1.2: <vendor 0x0424 product 0x9514> at usbus1
uhub1 on uhub0
uhub1: <vendor 0x0424 product 0x9514, class 9/0, rev 2.00/2.00, addr 2> on usbus1
uhub1: MTT enabled
uhub1: 5 ports with 4 removable, self powered
ugen1.3: <vendor 0x0424 product 0xec00> at usbus1
smsc0 on uhub1
smsc0: <vendor 0x0424 product 0xec00, rev 2.00/2.00, addr 3> on usbus1
smsc0: chip 0xec00, rev. 0002
miibus0: <MII bus> on smsc0
smscphy0: <SMC LAN8700 10/100 interface> PHY 1 on miibus0
smscphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
ue0: <USB Ethernet> on smsc0
ue0: Ethernet address: [_MAC_XXXXXXXXXX]
lo0: link state changed to UP
smsc0: chip 0xec00, rev. 0002
ue0: link state changed to DOWN
ue0: link state changed to UP