Launched in 2004, dmesgd aims to provide a user-submitted repository of searchable *BSD dmesgs. The dmesg(8) command displays the system message buffer's content, and during boot a copy is saved to /var/run/dmesg.boot. This buffer contains the operating system release, name and version, a list of devices identified, plus a whole host of other useful information. We hope others find this resource useful and further contribute to its growth. Contact us at [ admin at lists dot nycbug dot org ]. Note that this site is not a substitute for sending the dmesg directly to the respective project.
Date: 2024-04-18 06:12:19
From: Klaus
Description: RPI_CM4_PCIE_NVME FreeBSD_GH_PR #1179
Terminal ready
????Read start4.elf bytes 2251392 hnd 0xf8c
Read fixup4.dat bytes 5399 hnd 0xf83
Firmware: 82f3750a65fadae9a38077e3c2e217ad158c8d54 Mar 17 2023 10:50:39
0x00d03140 0x00000000 0x00001fff
MEM GPU: 76 ARM: 948 TOTAL: 1024
Starting start4.elf @ 0xfec00200 partition 0
+
MESS:00:00:03.529890:0: arasan: arasan_emmc_open
MESS:00:00:03.531550:0: arasan: arasan_emmc_set_clock C0: 0x00800000 C1: 0x000e0047 emmc: 200000000 actual: 390625 div: 0x00000100 target: 400000 min: 400000 max: 400000 delay: 5
MESS:00:00:03.651778:0: arasan: arasan_emmc_set_clock C0: 0x00800000 C1: 0x000e0047 emmc: 200000000 actual: 390625 div: 0x00000100 target: 400000 min: 400000 max: 400000 delay: 5
MESS:00:00:03.664650:0: arasan: arasan_emmc_set_clock C0: 0x00800f00 C1: 0x000e0047 emmc: 200000000 actual: 390625 div: 0x00000100 target: 400000 min: 390000 max: 400000 delay: 5
MESS:00:00:03.715603:0: arasan: arasan_emmc_set_clock C0: 0x00800f02 C1: 0x000e0407 emmc: 200000000 actual: 25000000 div: 0x00000004 target: 25000000 min: 0 max: 25000000 delay: 1
MESS:00:00:03.735549:0: brfs: File read: /mfs/sd/config.txt
MESS:00:00:03.738351:0: brfs: File read: 193 bytes
MESS:00:00:03.763525:0: HDMI0:EDID error reading EDID block 0 attempt 0
MESS:00:00:03.768030:0: HDMI0:EDID giving up on reading EDID block 0
MESS:00:00:03.784880:0: HDMI1:EDID error reading EDID block 0 attempt 0
MESS:00:00:03.789388:0: HDMI1:EDID giving up on reading EDID block 0
MESS:00:00:03.795449:0: brfs: File read: /mfs/sd/config.txt
MESS:00:00:03.800086:0: gpioman: gpioman_get_pin_num: pin DISPLAY_SDA not defined
MESS:00:00:03.806968:0: gpioman: gpioman_get_pin_num: pin LEDS_PWR_OK not defined
MESS:00:00:04.276251:0: gpioman: gpioman_get_pin_num: pin LEDS_PWR_OK not defined
MESS:00:00:04.281899:0: *** Restart logging
MESS:00:00:04.284540:0: brfs: File read: 193 bytes
MESS:00:00:04.294437:0: hdmi: HDMI0:EDID error reading EDID block 0 attempt 0
MESS:00:00:04.299467:0: hdmi: HDMI0:EDID giving up on reading EDID block 0
MESS:00:00:04.310091:0: hdmi: HDMI0:EDID error reading EDID block 0 attempt 0
MESS:00:00:04.315115:0: hdmi: HDMI0:EDID giving up on reading EDID block 0
MESS:00:00:04.332188:0: hdmi: HDMI1:EDID error reading EDID block 0 attempt 0
MESS:00:00:04.337221:0: hdmi: HDMI1:EDID giving up on reading EDID block 0
MESS:00:00:04.353057:0: hdmi: HDMI1:EDID error reading EDID block 0 attempt 0
MESS:00:00:04.358127:0: hdmi: HDMI1:EDID giving up on reading EDID block 0
MESS:00:00:04.371596:0: HDMI0: hdmi_pixel_encoding: 300000000
MESS:00:00:04.374232:0: HDMI1: hdmi_pixel_encoding: 300000000
MESS:00:00:04.380393:0: kernel=u-boot.bin
MESS:00:00:04.383513:0: gpioman: gpioman_get_pin_num: pin CAMERA_0_I2C_PORT not defined
MESS:00:00:04.395431:0: dtb_file 'bcm2711-rpi-cm4.dtb'
MESS:00:00:04.407789:0: brfs: File read: /mfs/sd/bcm2711-rpi-cm4.dtb
MESS:00:00:04.411038:0: Loaded 'bcm2711-rpi-cm4.dtb' to 0x4000 size 0xd899
MESS:00:00:04.431265:0: brfs: File read: 55449 bytes
MESS:00:00:04.505308:0: brfs: File read: /mfs/sd/config.txt
MESS:00:00:04.507798:0: dtparam: audio=on
MESS:00:00:04.515588:0: dtparam: i2c_arm=on
MESS:00:00:04.525432:0: dtparam: spi=on
MESS:00:00:04.534343:0: brfs: File read: 193 bytes
MESS:00:00:04.537150:0: brfs: File read: /mfs/sd/overlays/mmc.dtbo
MESS:00:00:04.554232:0: Loaded overlay 'mmc'
MESS:00:00:04.633218:0: brfs: File read: 1221 bytes
MESS:00:00:04.636638:0: brfs: File read: /mfs/sd/overlays/disable-bt.dtbo
MESS:00:00:04.679920:0: Loaded overlay 'disable-bt'
MESS:00:00:04.786855:0: brfs: File read: 1073 bytes
MESS:00:00:04.789236:0: Failed to open command line file 'cmdline.txt'
MESS:00:00:05.050213:0: brfs: File read: /mfs/sd/armstub8-gic.bin
MESS:00:00:05.053246:0: Loaded 'armstub8-gic.bin' to 0x0 size 0x1700
MESS:00:00:05.059357:0: brfs: File read: 5888 bytes
MESS:00:00:05.199547:0: brfs: File read: /mfs/sd/u-boot.bin
MESS:00:00:05.202064:0: Loaded 'u-boot.bin' to 0x80000 size 0x98328
MESS:00:00:05.208078:0: Device tree loaded to 0x4000 (size 0xdddf)
MESS:00:00:05.217459:0: uart: Set PL011 baud rate to 103448.300000 Hz
MESS:00:00:05.223787:0: uart: Baud rate change done...
MESS:00:00:05.225848:0: uart: Baud rate change done...
MESS:00:00:05.231247:0: gpioman: gpioman_get_pin_num: pin SDCARD_CONTROL_POWER not defined
U-Boot 2024.01 (Apr 15 2024 - 12:14:37 +0000)
DRAM: 948 MiB (effective 7.9 GiB)
RPI Compute Module 4 (0xd03140)
Core: 211 devices, 16 uclasses, devicetree: board
MMC: mmc@7e300000: 3, mmc@7e340000: 0
Loading Environment from FAT... ** Bad device specification mmc 1 **
In: serial,usbkbd
Out: serial,vidconsole
Err: serial,vidconsole
Net: eth0: ethernet@7d580000
PCIe BRCM: link up, 5.0 Gbps x1 (SSC)
starting USB...
No working controllers found
Hit any key to stop autoboot: 0
----
....
** Booting bootflow '[_EMAIL_XXXXXXXXXXXXXXXX]_1' with efi
No EFI system partition
No EFI system partition
Failed to persist EFI variables
Booting /efi\boot\bootaa64.efi
Consoles: EFI console
Reading loader env vars from /efi/freebsd/loader.env
Setting currdev to disk0p1:
FreeBSD/arm64 EFI loader, Revision 1.1
(Mon Apr 15 15:16:44 UTC 2024 [_EMAIL_XXXXXXXXXXXXXXXXXXX])
Command line arguments: loader.efi
Image base: 0x39e1f000
EFI version: 2.100
EFI Firmware: Das U-Boot (rev 8228.256)
Console: efi,comconsole (0)
Load Path: /efi\boot\bootaa64.efi
Load Device: /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b,0000000000000000)/VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b,6d00000003000000)/eMMC(0)/eMMC(1)/HD(1,0x01,0,0x800,0x19000)
Trying ESP: /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b,0000000000000000)/VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b,6d00000003000000)/eMMC(0)/eMMC(1)/HD(1,0x01,0,0x800,0x19000)
Setting currdev to disk0p1:
Trying: /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b,0000000000000000)/VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b,6d00000003000000)/eMMC(0)/eMMC(1)/HD(2,0x01,0,0x19800,0x3a24800)
Setting currdev to disk0p2:
Loading /boot/defaults/loader.conf
Loading /boot/defaults/loader.conf
Loading /boot/device.hints
Loading /boot/loader.conf
Loading /boot/loader.conf.local
Loading kernel...
/boot/kernel/kernel text=0x2a8 text=0x97a970 text=0x2b308c data=0x166a50 data=0x0+0x370000 0x8+0x164df0+0x8+0x1958e6
Loading configured modules...
/boot/kernel/umodem.ko text=0x20c0 text=0x1548 data=0x708+0x4 0x8+0xed0+0x8+0xb2d
loading required module 'ucom'
/boot/kernel/ucom.ko text=0x2620 text=0x31a0 data=0x970+0x858 0x8+0x1290+0x8+0xbd0
/boot/entropy size=0x1000
/etc/hostid size=0x25
..........
Using DTB provided by EFI at 0x39ef3000.
EFI framebuffer information:
addr, size 0x3eac2000, 0x103000
dimensions 592 x 448
stride 592
masks 0x00ff0000, 0x0000ff00, 0x000000ff, 0xff000000
---<<BOOT>>---
GDB: debug ports: uart
GDB: current port: uart
KDB: debugger backends: ddb gdb
KDB: current backend: ddb
WARNING: Cannot find freebsd,dts-version property, cannot check DTB compliance
Type Physical Virtual #Pages Attr
Reserved 000000000000 000000000000 00000002 WB
ConventionalMemory 000000002000 000000002000 00031e1b WB
LoaderData 000031e1d000 000031e1d000 00000001 WB
BootServicesData 000031e1e000 000031e1e000 00000001 WB
LoaderCode 000031e1f000 000031e1f000 00004000 WB
LoaderData 000035e1f000 000035e1f000 00004000 WB
LoaderCode 000039e1f000 000039e1f000 000000d0 WB
BootServicesData 000039eef000 000039eef000 00000004 WB
ACPIReclaimMemory 000039ef3000 000039ef3000 00000011 WB
BootServicesData 000039f04000 000039f04000 00000004 WB
RuntimeServicesData 000039f08000 000039f08000 00000001 WB RUNTIME
BootServicesData 000039f09000 000039f09000 00000001 WB
RuntimeServicesData 000039f0a000 000039f0a000 00000022 WB RUNTIME
BootServicesData 000039f2c000 000039f2c000 0000000a WB
RuntimeServicesData 000039f36000 000039f36000 00000001 WB RUNTIME
BootServicesData 000039f37000 000039f37000 00000003 WB
BootServicesCode 000039f3a000 000039f3a000 00001406 WB
RuntimeServicesCode 00003b340000 00003b340000 00000010 WB RUNTIME
BootServicesCode 00003b350000 00003b350000 000000b0 WB
Reserved 00003ef62000 00003ef62000 00000002 WB
BootServicesData 000040000000 000040000000 000bc000 WB
MemoryMappedIO 0000fe100000 0000fe100000 00000001 RUNTIME
BootServicesData 000100000000 000100000000 00100000 WB
Physical memory chunk(s):
0x00002000 - 0x3b3fffff, 947 MB ( 242686 pages)
0x40000000 - 0xfbffffff, 3008 MB ( 770048 pages)
0x100000000 - 0x1ffffffff, 4096 MB (1048576 pages)
Excluded memory regions:
0x32000000 - 0x3379efff, 23 MB ( 6047 pages) NoAlloc
0x39ef3000 - 0x39f03fff, 0 MB ( 17 pages) NoAlloc
0x39f08000 - 0x39f08fff, 0 MB ( 1 pages) NoAlloc
0x39f0a000 - 0x39f2bfff, 0 MB ( 34 pages) NoAlloc
0x39f36000 - 0x39f36fff, 0 MB ( 1 pages) NoAlloc
0x3b340000 - 0x3b34ffff, 0 MB ( 16 pages) NoAlloc
0x3eac2000 - 0x3ebc4fff, 1 MB ( 259 pages) NoAlloc
0x3ef62000 - 0x3ef63fff, 0 MB ( 2 pages) NoAlloc NoDump
Found 4 CPUs in the device tree
Copyright (c) 1992-2024 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 15.0-CURRENT #4 main-n269491-f276adc14843-dirty: Thu Apr 18 07:14:34 CEST 2024
root@fbsd5pro:/usr/obj/usr/src/arm64.aarch64/sys/GENERIC arm64
FreeBSD clang version 18.1.3 (https://github.com/llvm/llvm-project.git llvmorg-18.1.3-0-gc13b7485b879)
WARNING: WITNESS option enabled, expect reduced performance.
VT(efifb): resolution 592x448
Preloaded elf kernel "boot/kernel/kernel" at 0xffff00000155f000.
Preloaded boot_entropy_platform "efi_rng_seed" at 0xffff000001568340.
Preloaded TSLOG data "TSLOG" at 0xffff000001568398.
module scmi already present!
real memory = 8443125760 (8051 MB)
Physical memory chunk(s):
0x00000000002000 - 0x00000031ffffff, 838852608 bytes (204798 pages)
0x0000003379f000 - 0x00000039ef2fff, 108347392 bytes (26452 pages)
0x00000039f04000 - 0x00000039f07fff, 16384 bytes (4 pages)
0x00000039f09000 - 0x00000039f09fff, 4096 bytes (1 pages)
0x00000039f2c000 - 0x00000039f35fff, 40960 bytes (10 pages)
0x00000039f37000 - 0x0000003b33ffff, 21008384 bytes (5129 pages)
0x0000003b350000 - 0x0000003b3fffff, 720896 bytes (176 pages)
0x00000040000000 - 0x000000fbffffff, 3154116608 bytes (770048 pages)
0x00000100000000 - 0x000001f35f5fff, 4083113984 bytes (996854 pages)
avail memory = 8204103680 (7824 MB)
Starting CPU 1 (1)
Starting CPU 2 (2)
Starting CPU 3 (3)
FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
random: no preloaded entropy cache
random: read 2048 bytes from platform bootloader
random: unblocking device.
VIMAGE (virtualized network stack) enabled
hostuuid: using 00000000-0000-0000-0000-000000000000
ULE: setup cpu 0
ULE: setup cpu 1
ULE: setup cpu 2
ULE: setup cpu 3
random: entropy device external interface
snd_unit_init() u=0x00ff8000 [512] d=0x00007c00 [32] c=0x000003ff [1024]
feeder_register: snd_unit=-1 snd_maxautovchans=16 latency=2 feeder_rate_min=1 feeder_rate_max=2016000 feeder_rate_round=25
firmware: 'tegra210_xusb_fw' version 0: 132608 bytes loaded at 0xffff000000b08830
MAP 39f08000 mode 2 pages 1
MAP 39f0a000 mode 2 pages 34
MAP 39f36000 mode 2 pages 1
MAP 3b340000 mode 2 pages 16
MAP fe100000 mode 4 pages 1
kbd0 at kbdmux0
mem: <memory>
null: <full device, null device, zero device>
openfirm: <Open Firmware control device>
tcp_log: tcp_log device
crypto: <crypto core>
ofwbus0: <Open Firmware Device Tree>
simplebus0: <Flattened device tree simple bus> on ofwbus0
ofw_clkbus0: <OFW clocks bus> on ofwbus0
clk_fixed0: <Fixed clock> on ofw_clkbus0
Clock: osc, parent: none, freq: 54000000
clk_fixed1: <Fixed clock> on ofw_clkbus0
Clock: otg, parent: none, freq: 480000000
clk_fixed2: <Fixed clock> on ofwbus0
Clock: 27MHz-clock, parent: none, freq: 27000000
clk_fixed3: <Fixed clock> on ofwbus0
Clock: 108MHz-clock, parent: none, freq: 108000000
simplebus1: <Flattened device tree simple bus> on ofwbus0
simplebus2: <Flattened device tree simple bus> on ofwbus0
regfix0: <Fixed Regulator> on ofwbus0
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
regfix1: <Fixed Regulator> on ofwbus0
regfix2: <Fixed Regulator> on ofwbus0
regfix3: <Fixed Regulator> on ofwbus0
regfix4: <Fixed Regulator> on ofwbus0
simplebus3: <Flattened device tree simple bus> on ofwbus0
simple_mfd0: <Simple MFD (Multi-Functions Device)> mem 0x7d5d2000-0x7d5d2eff on simplebus0
bcm2835_firmware0: <BCM2835 Firmware> on simplebus0
ofw_clkbus1: <OFW clocks bus> on bcm2835_firmware0
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
psci0: <ARM Power State Co-ordination Interface Driver> on ofwbus0
psci0: PSCI version 0.2 compatible
Found SMCCC version 1.0
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
gic0: <ARM Generic Interrupt Controller> mem 0x40041000-0x40041fff,0x40042000-0x40043fff,0x40044000-0x40045fff,0x40046000-0x40047fff irq 30 on simplebus0
gic0: pn 0x2, arch 0x2, rev 0x1, implementer 0x43b irqs 256
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
gpio0: <BCM2708/2835 GPIO controller> mem 0x7e200000-0x7e2000b3 irq 14,15 on simplebus0
gpiobus0: <OFW GPIO bus> on gpio0
Processing 1 pin-config node(s) in pinctrl-0 for serial@7e201000
Processing 2 pin-config node(s) in pinctrl-0 for spi@7e204000
gpio0: set pin 9 to func 4
gpio0: set pin 10 to func 4
gpio0: set pin 11 to func 4
gpio0: set pin 8 to func 1
gpio0: set pin 7 to func 1
Processing 1 pin-config node(s) in pinctrl-0 for mmc@7e300000
gpio0: set pin 48 to func 7, pull 0
gpio0: set pin 49 to func 7, pull 2
gpio0: set pin 50 to func 7, pull 2
gpio0: set pin 51 to func 7, pull 2
gpio0: set pin 52 to func 7, pull 2
gpio0: set pin 53 to func 7, pull 2
Processing 1 pin-config node(s) in pinctrl-0 for i2c@7e804000
Processing 1 pin-config node(s) in pinctrl-0 for mailbox@7e00b840
gpio1: <Raspberry Pi Firmware GPIO controller> on bcm2835_firmware0
gpiobus1: <GPIO bus> on gpio1
regfix0: Cannot configure GPIO pin: 5
REGNODE_INIT failed: 6
regfix0: Cannot register regulator.
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
regfix2: Cannot set GPIO pin: 6
REGNODE_INIT failed: 6
regfix2: Cannot register regulator.
mbox0: <BCM2835 VideoCore Mailbox> mem 0x7e00b880-0x7e00b8bf irq 13 on simplebus0
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
gpioregulator0: <GPIO controlled regulator> on ofwbus0
Checking root against raspberrypi,model-b
Checking root against brcm,bcm2835
Checking root against brcm,bcm2709
Checking root against brcm,bcm2836
Checking root against brcm,bcm2837
Checking root against brcm,bcm2711
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
generic_timer0: <ARMv8 Generic Timer> irq 4,5,6,7 on ofwbus0
generic_timer0: allocated irq for 'sec-phys'
generic_timer0: allocated irq for 'phys'
generic_timer0: allocated irq for 'virt'
generic_timer0: allocated irq for 'hyp-phys'
ofwbus0: no default resources for rid = 4, type = 1
generic_timer0: could not allocate irq for optional interrupt 'hyp-virt'
Timecounter "ARM MPCore Timecounter" frequency 54000000 Hz quality 1000
Event timer "ARM MPCore Eventtimer" frequency 54000000 Hz quality 1000
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
bcm_dma0: <BCM2835 DMA Controller> mem 0x7e007000-0x7e007aff irq 31,32,33,34,35,36,37,38,39,40,41 on simplebus0
usb_nop_xceiv0: <USB NOP PHY> on ofwbus0
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
clk_fixed4: clock-fixed has no clock-frequency
efirtc0: cannot read EFI realtime clock, error 78
ram0: reserving memory region: 2000-32000000
ram0: reserving memory region: 3379f000-39ef3000
ram0: reserving memory region: 39f04000-39f08000
ram0: reserving memory region: 39f09000-39f0a000
ram0: reserving memory region: 39f2c000-39f36000
ram0: reserving memory region: 39f37000-3b340000
ram0: reserving memory region: 3b350000-3b400000
ram0: reserving memory region: 40000000-fc000000
ram0: reserving memory region: 100000000-200000000
ofwbus0: <framebuffer@3eac2000> mem 0x3eac2000-0x3ebc4fff compat simple-framebuffer (no driver attached)
simplebus0: <timer@7e003000> mem 0x7e003000-0x7e003fff irq 8,9,10,11 disabled compat brcm,bcm2835-system-timer (no driver attached)
simplebus0: <txp@7e004000> mem 0x7e004000-0x7e00401f irq 12 disabled compat brcm,bcm2835-txp (no driver attached)
bcm2835_clkman0: <BCM283x Clock Manager> mem 0x7e101000-0x7e102fff on simplebus0
gpioc0: <GPIO controller> on gpio0
simplebus0: no default resources for rid = 0, type = 4
simplebus0: no default resources for rid = 0, type = 4
uart0: <PrimeCell UART (PL011)> mem 0x7e201000-0x7e2011ff irq 16 on simplebus0
uart0: console (115200,n,8,1)
uart0: fast interrupt
uart0: PPS capture mode: DCD
simplebus0: <mmc@7e202000> mem 0x7e202000-0x7e2020ff irq 17 disabled compat brcm,bcm2835-sdhost (no driver attached)
simplebus0: <i2s@7e203000> mem 0x7e203000-0x7e203023 disabled compat brcm,bcm2835-i2s (no driver attached)
spi0: <BCM2708/2835 SPI controller> mem 0x7e204000-0x7e2041ff irq 18 on simplebus0
spibus0: <OFW SPI bus> on spi0
spibus0: <unknown card> at cs 0 mode 0
spibus0: <unknown card> at cs 1 mode 0
simplebus0: <i2c@7e205000> mem 0x7e205000-0x7e2051ff irq 19 disabled compat brcm,bcm2711-i2c (no driver attached)
simplebus0: <dpi@7e208000> mem 0x7e208000-0x7e20808b disabled compat brcm,bcm2835-dpi (no driver attached)
simplebus0: <dsi@7e209000> mem 0x7e209000-0x7e209077 irq 20 disabled compat brcm,bcm2835-dsi0 (no driver attached)
simplebus0: <aux@7e215000> mem 0x7e215000-0x7e215007 compat brcm,bcm2835-aux (no driver attached)
simplebus0: <serial@7e215040> mem 0x7e215040-0x7e21507f irq 21 disabled compat brcm,bcm2835-aux-uart (no driver attached)
simplebus0: <spi@7e215080> mem 0x7e215080-0x7e2150bf irq 22 disabled compat brcm,bcm2835-aux-spi (no driver attached)
simplebus0: <spi@7e2150c0> mem 0x7e2150c0-0x7e2150ff irq 23 disabled compat brcm,bcm2835-aux-spi (no driver attached)
simplebus0: <pwm@7e20c000> mem 0x7e20c000-0x7e20c027 disabled compat brcm,bcm2835-pwm (no driver attached)
sdhci_bcm0: <Broadcom 2708 SDHCI controller> mem 0x7e300000-0x7e3000ff irq 24 on simplebus0
sdhci_bcm0: SDHCI frequency: 250MHz
sdhci_bcm0-slot0: 250MHz HS 4bits VDD: 3.3V VCCQ: 3.3V DRV: B PIO removable
sdhci_bcm0-slot0: ============== REGISTER DUMP ==============
sdhci_bcm0-slot0: Sys addr: 0x00000000 | Version: 0x00009902
sdhci_bcm0-slot0: Blk size: 0x00000000 | Blk cnt: 0x00000000
sdhci_bcm0-slot0: Argument: 0x00000000 | Trn mode: 0x00000000
sdhci_bcm0-slot0: Present: 0x000f0000 | Host ctl: 0x00000000
sdhci_bcm0-slot0: Power: 0x0000000f | Blk gap: 0x00000000
sdhci_bcm0-slot0: Wake-up: 0x00000000 | Clock: 0x00003947
sdhci_bcm0-slot0: Timeout: 0x00000000 | Int stat: 0x00000000
sdhci_bcm0-slot0: Int enab: 0x027f003b | Sig enab: 0x00000000
sdhci_bcm0-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000
sdhci_bcm0-slot0: Caps: 0x00000000 | Caps2: 0x00000000
sdhci_bcm0-slot0: Max curr: 0x00000001 | ADMA err: 0x00000000
sdhci_bcm0-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000
sdhci_bcm0-slot0: ===========================================
sdhci_bcm0-slot0: Card inserted
mmc0: <MMC/SD bus> on sdhci_bcm0
simplebus0: <hvs@7e400000> mem 0x7e400000-0x7e407fff irq 25 disabled compat brcm,bcm2711-hvs (no driver attached)
simplebus0: <dsi@7e700000> mem 0x7e700000-0x7e70008b irq 26 disabled compat brcm,bcm2711-dsi1 (no driver attached)
iichb0: <BCM2708/2835 BSC controller> mem 0x7e804000-0x7e804fff irq 27 on simplebus0
simplebus0: <usb@7e980000> mem 0x7e980000-0x7e98ffff,0x7e00b200-0x7e00b3ff irq 28,29 disabled compat brcm,bcm2708-usb (no driver attached)
simplebus0: <interrupt-controller@40000000> mem 0x40000000-0x400000ff compat brcm,bcm2836-l1-intc (no driver attached)
simple_mfd0: <thermal> mem 0x7d5d2000-0x7d5d2eff compat brcm,bcm2711-thermal (no driver attached)
bcmwd0: <BCM2708/2835 Watchdog> mem 0x7e100000-0x7e100113,0x7e00a000-0x7e00a023,0x7ec11000-0x7ec1101f on simplebus0
bcmrng0: <Broadcom BCM2835/BCM2838 RNG> mem 0x7e104000-0x7e104027 on simplebus0
bcmrng0: simplebus0: <serial@7e201400> mem 0x7e201400-0x7e2015ff irq 42 disabled compat arm,pl011 (no driver attached)
simplebus0: <serial@7e201600> mem 0x7e201600-0x7e2017ff irq 43 disabled compat arm,pl011 (no driver attached)
simplebus0: <serial@7e201800> mem 0x7e201800-0x7e2019ff irq 44 disabled compat arm,pl011 (no driver attached)
simplebus0: <serial@7e201a00> mem 0x7e201a00-0x7e201bff irq 45 disabled compat arm,pl011 (no driver attached)
simplebus0: <spi@7e204600> mem 0x7e204600-0x7e2047ff irq 46 disabled compat brcm,bcm2835-spi (no driver attached)
simplebus0: <spi@7e204800> mem 0x7e204800-0x7e2049ff irq 47 disabled compat brcm,bcm2835-spi (no driver attached)
simplebus0: <spi@7e204a00> mem 0x7e204a00-0x7e204bff irq 48 disabled compat brcm,bcm2835-spi (no driver attached)
simplebus0: <spi@7e204c00> mem 0x7e204c00-0x7e204dff irq 49 disabled compat brcm,bcm2835-spi (no driver attached)
simplebus0: <i2c@7e205600> mem 0x7e205600-0x7e2057ff irq 50 disabled compat brcm,bcm2711-i2c (no driver attached)
simplebus0: <i2c@7e205800> mem 0x7e205800-0x7e2059ff irq 51 disabled compat brcm,bcm2711-i2c (no driver attached)
simplebus0: <i2c@7e205a00> mem 0x7e205a00-0x7e205bff irq 52 disabled compat brcm,bcm2711-i2c (no driver attached)
simplebus0: <i2c@7e205c00> mem 0x7e205c00-0x7e205dff irq 53 disabled compat brcm,bcm2711-i2c (no driver attached)
simplebus0: <pixelvalve@7e206000> mem 0x7e206000-0x7e2060ff irq 54 disabled compat brcm,bcm2711-pixelvalve0 (no driver attached)
simplebus0: <pixelvalve@7e207000> mem 0x7e207000-0x7e2070ff irq 55 disabled compat brcm,bcm2711-pixelvalve1 (no driver attached)
simplebus0: <pixelvalve@7e20a000> mem 0x7e20a000-0x7e20a0ff irq 56 disabled compat brcm,bcm2711-pixelvalve2 (no driver attached)
simplebus0: <pwm@7e20c800> mem 0x7e20c800-0x7e20c827 disabled compat brcm,bcm2835-pwm (no driver attached)
simplebus0: <pixelvalve@7e216000> mem 0x7e216000-0x7e2160ff irq 57 disabled compat brcm,bcm2711-pixelvalve4 (no driver attached)
simplebus0: <pixelvalve@7ec12000> mem 0x7ec12000-0x7ec120ff irq 58 disabled compat brcm,bcm2711-pixelvalve3 (no driver attached)
simplebus0: <vec@7ec13000> mem 0x7ec13000-0x7ec13fff irq 59 disabled compat brcm,bcm2711-vec (no driver attached)
simplebus0: <clock@7ef00000> mem 0x7ef00000-0x7ef0000f disabled compat brcm,brcm2711-dvp (no driver attached)
simplebus0: <interrupt-controller@7ef00100> mem 0x7ef00100-0x7ef0012f irq 60 disabled compat brcm,bcm2711-l2-intc (no driver attached)
simplebus0: <hdmi@7ef00700> mem 0x7ef00700-0x7ef009ff,0x7ef00300-0x7ef004ff,0x7ef00f00-0x7ef00f7f,0x7ef00f80-0x7ef00fff,0x7ef01b00-0x7ef01cff,0x7ef01f00-0x7ef022ff,0x7ef00200-0x7ef0027f,0x7ef04300-0x7ef043ff,0x7ef20000-0x7ef200ff,0x7ef00100-0x7ef0012f irq 61,62,63,64,65,66 disabled compat brcm,bcm2711-hdmi0 (no driver attached)
simplebus0: <i2c@7ef04500> mem 0x7ef04500-0x7ef045ff,0x7ef00b00-0x7ef00dff disabled compat brcm,bcm2711-hdmi-i2c (no driver attached)
simplebus0: <hdmi@7ef05700> mem 0x7ef05700-0x7ef059ff,0x7ef05300-0x7ef054ff,0x7ef05f00-0x7ef05f7f,0x7ef05f80-0x7ef05fff,0x7ef06b00-0x7ef06cff,0x7ef06f00-0x7ef072ff,0x7ef00280-0x7ef002ff,0x7ef09300-0x7ef093ff,0x7ef20000-0x7ef200ff,0x7ef00100-0x7ef0012f irq 67,68,69,70,71,72 disabled compat brcm,bcm2711-hdmi1 (no driver attached)
simplebus0: <i2c@7ef09500> mem 0x7ef09500-0x7ef095ff,0x7ef05b00-0x7ef05dff disabled compat brcm,bcm2711-hdmi-i2c (no driver attached)
simplebus0: <mmcnr@7e300000> mem 0x7e300000-0x7e3000ff irq 73 disabled compat brcm,bcm2835-mmc (no driver attached)
simplebus0: <firmwarekms@7e600000> mem 0x7e600000-0x7e6000ff irq 74 disabled compat raspberrypi,rpi-firmware-kms-2711 (no driver attached)
simplebus0: <smi@7e600000> mem 0x7e600000-0x7e6000ff irq 75 disabled compat brcm,bcm2835-smi (no driver attached)
simplebus0: <csi@7e800000> mem 0x7e800000-0x7e8007ff,0x7e802000-0x7e802003 irq 76 disabled compat brcm,bcm2835-unicam (no driver attached)
simplebus0: <csi@7e801000> mem 0x7e801000-0x7e8017ff,0x7e802004-0x7e802007 irq 77 disabled compat brcm,bcm2835-unicam (no driver attached)
simplebus0: <axiperf> mem 0x7e009800-0x7e0098ff,0x7ee08000-0x7ee080ff disabled compat brcm,bcm2711-axiperf (no driver attached)
simplebus0: <i2c0mux> disabled compat i2c-mux-pinctrl (no driver attached)
gpioc1: <GPIO controller> on gpio1
bcm2835_firmware0: <reset> compat raspberrypi,firmware-reset (no driver attached)
bcm2835_firmware0: <vcio> compat raspberrypi,vcio (no driver attached)
simplebus0: <power> compat raspberrypi,bcm2835-power (no driver attached)
simplebus0: <mailbox@7e00b840> mem 0x7e00b840-0x7e00b87b irq 78 compat brcm,bcm2711-vchiq (no driver attached)
simplebus0: <gpiomem> mem 0x7e200000-0x7e200fff compat brcm,bcm2835-gpiomem (no driver attached)
fb0: <BCM2835 VT framebuffer driver> on simplebus0
fb0: keeping existing fb bpp of 32
fbd0 on fb0
WARNING: Device "fb" is Giant locked and may be deleted before FreeBSD 15.0.
VT: Replacing driver "efifb" with new "fb".
fb0: 592x448(592x448@0,0) 32bpp
fb0: fbswap: 1, pitch 2368, base 0x3eac2000, screen_size 1060864
ofwbus0: <gpu> disabled compat brcm,bcm2711-vc5 (no driver attached)
sdhci_bcm1: <Broadcom 2708 SDHCI controller> mem 0x7e340000-0x7e3400ff irq 79 on simplebus1
sdhci_bcm1: SDHCI frequency: 100MHz
sdhci_bcm1-slot0: 100MHz HS 8bits VDD: 3.3V 1.8V VCCQ: 3.3V DRV: BC PIO embedded
sdhci_bcm1-slot0: ============== REGISTER DUMP ==============
sdhci_bcm1-slot0: Sys addr: 0x3811ce00 | Version: 0x00001002
sdhci_bcm1-slot0: Blk size: 0x00007200 | Blk cnt: 0x00000000
sdhci_bcm1-slot0: Argument: 0x00000000 | Trn mode: 0x00000000
sdhci_bcm1-slot0: Present: 0x1fff0000 | Host ctl: 0x00000002
sdhci_bcm1-slot0: Power: 0x0000000f | Blk gap: 0x00000080
sdhci_bcm1-slot0: Wake-up: 0x00000000 | Clock: 0x00000107
sdhci_bcm1-slot0: Timeout: 0x0000000e | Int stat: 0x00000000
sdhci_bcm1-slot0: Int enab: 0x027f003b | Sig enab: 0x00000000
sdhci_bcm1-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000
sdhci_bcm1-slot0: Caps: 0x45ee6432 | Caps2: 0x0000a525
sdhci_bcm1-slot0: Max curr: 0x00080008 | ADMA err: 0x00000000
sdhci_bcm1-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000
sdhci_bcm1-slot0: ===========================================
sdhci_bcm1: vqmmc-supply regulator found
sdhci_bcm1-slot0: Card inserted
mmc1: <MMC/SD bus> on sdhci_bcm1
pmu0: <Performance Monitoring Unit> irq 0,1,2,3 on ofwbus0
ofwbus0: no default resources for rid = 4, type = 1
cpulist0: <Open Firmware CPU Group> on ofwbus0
cpu0: <Open Firmware CPU> on cpulist0
cpu0: missing 'clock-frequency' property
bcm2835_cpufreq0: <CPU Frequency Control> on cpu0
cpu1: <Open Firmware CPU> on cpulist0
cpu1: missing 'clock-frequency' property
cpu2: <Open Firmware CPU> on cpulist0
cpu2: missing 'clock-frequency' property
cpu3: <Open Firmware CPU> on cpulist0
cpu3: missing 'clock-frequency' property
pcib0: <BCM2838-compatible PCI-express controller> mem 0x7d500000-0x7d50930f irq 80,81 on simplebus2
pcib0: parsing FDT for ECAM0:
pcib0: Bus is not cache-coherent
pcib0: PCI addr: 0xc0000000, CPU addr: 0x600000000, Size: 0x40000000, Type: memory
pcib0: hardware identifies as revision 0x304.
pcib0: note: reported link speed is 5.0 GT/s.
pcib0: note: enabling L1SS due to OF property brcm,enable-l1ss
pci0: <OFW PCI bus> on pcib0
pci0: domain=0, physical bus=0
found-> vendor=0x14e4, dev=0x2711, revid=0x00
domain=0, bus=0, slot=0, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0000, statreg=0x0010, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=0
powerspec 3 supports D0 D3 current D0
secbus=1, subbus=1
pcib1: <PCI-PCI bridge> irq 91 at device 0.0 on pci0
pcib1: domain 0
pcib1: secondary bus 1
pcib1: subordinate bus 1
pcib1: memory decode 0xc0000000-0xc00fffff
pci1: <OFW PCI bus> on pcib1
pcib1: allocated bus range (1-1) for rid 0 of pci1
pci1: domain=0, physical bus=1
found-> vendor=0x15b7, dev=0x5009, revid=0x01
domain=0, bus=1, slot=0, func=0
class=01-08-02, hdrtype=0x00, mfdev=0
cmdreg=0x0000, statreg=0x0010, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=0
powerspec 3 supports D0 D3 current D0
MSI supports 32 messages, 64 bit
MSI-X supports 17 messages in maps 0x10 and 0x20
map[10]: type Memory, range 64, base 0, size 14, memory disabled
map[20]: type Memory, range 64, base 0, size 8, memory disabled
pcib1: slot 0 INTA is routed to irq 92
nvme0: <Generic NVMe Device> irq 92 at device 0.0 on pci1
pcib1: allocated memory range (0xc0000000-0xc0003fff) for rid 10 of nvme0
nvme0: Lazy allocation of 0x4000 bytes rid 0x10 type 3 at 0xc0000000
pcib1: allocated memory range (0xc0004000-0xc00040ff) for rid 20 of nvme0
nvme0: Lazy allocation of 0x100 bytes rid 0x20 type 3 at 0xc0004000
nvme0: attempting to allocate 5 MSI-X vectors (17 supported)
nvme0: unable to allocate MSI-X
nvme0: attempting to allocate 2 MSI vectors (32 supported)
nvme0: using IRQs 93-94 for MSI
nvme0: CapLo: 0x140103ff: MQES 1023, CQR, TO 20
nvme0: CapHi: 0x00000030: DSTRD 0, NSSRS, CSS 1, CPS 0, MPSMIN 0, MPSMAX 0
nvme0: Version: 0x00010400: 1.4
genet0: <RPi4 Gigabit Ethernet> mem 0x7d580000-0x7d58ffff irq 82,83 on simplebus2
genet0: GENET version 5.0 phy 0x0000
miibus0: <MII bus> on genet0
brgphy0: <BCM54213PE 1000BASE-T media interface> PHY 0 on miibus0
brgphy0: OUI 0x18c086, model 0x000a, rev. 2
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto
genet0: bpf attached
genet0: Ethernet address: [_MAC_XXXXXXXXXX]
simplebus2: <dma@7e007b00> mem 0x7e007b00-0x7e007eff irq 84,85,86,87 compat brcm,bcm2711-dma (no driver attached)
simplebus2: <xhci@7e9c0000> mem 0x7e9c0000-0x7eabffff irq 88 disabled compat generic-xhci (no driver attached)
simplebus2: <codec@7eb10000> mem 0x7eb10000-0x7eb10fff,0x7eb00000-0x7eb0ffff irq 89 compat raspberrypi,rpivid-vid-decoder (no driver attached)
clk_fixed4: clock-fixed has no clock-frequency
ofwbus0: <cam1_clk> disabled compat fixed-clock (no driver attached)
ofwbus0: <cam0_regulator> disabled compat regulator-fixed (no driver attached)
clk_fixed4: clock-fixed has no clock-frequency
ofwbus0: <cam0_clk> disabled compat fixed-clock (no driver attached)
gpioled0: <GPIO LEDs> on ofwbus0
lock order reversal: (sleepable after non-sleepable)
1st 0xffff000000ddf938 LED mtx (LED mtx, sleep mutex) @ /usr/src/sys/dev/led/led.c:295
2nd 0xffffa0010285bc10 Raspberry Pi firmware gpio (Raspberry Pi firmware gpio, sx) @ /usr/src/sys/arm/broadcom/bcm2835/raspberrypi_gpio.c:250
lock order LED mtx -> Raspberry Pi firmware gpio attempted at:
#0 0xffff00000051e0b0 at witness_checkorder+0xaa4
#1 0xffff0000004b2d40 at _sx_xlock+0x70
#2 0xffff000000928104 at rpi_fw_gpio_pin_set+0xe0
#3 0xffff0000001d8488 at led_create_state+0x15c
#4 0xffff00000019eea4 at gpioled_attach+0x290
#5 0xffff0000004e4bf4 at device_attach+0x3f4
#6 0xffff0000004e4764 at device_probe_and_attach+0x80
#7 0xffff0000004e6cb8 at bus_generic_new_pass+0x100
#8 0xffff0000004e6c68 at bus_generic_new_pass+0xb0
#9 0xffff0000004e6c68 at bus_generic_new_pass+0xb0
#10 0xffff0000004e15e4 at bus_set_pass+0x50
#11 0xffff00000042a5dc at mi_startup+0x1e0
#12 0xffff0000000008a8 at virtdone+0x68
uma_zalloc_debug: zone "malloc-64" with the following non-sleepable locks held:
exclusive sleep mutex LED mtx (LED mtx) r = 0 (0xffff000000ddf938) locked @ /usr/src/sys/dev/led/led.c:295
stack backtrace:
#0 0xffff00000051e51c at witness_debugger+0x60
#1 0xffff00000051f788 at witness_warn+0x3e4
#2 0xffff0000007e8020 at uma_zalloc_debug+0x34
#3 0xffff0000007e7bbc at uma_zalloc_arg+0x30
#4 0xffff00000047a92c at malloc+0x8c
#5 0xffff00000091cd18 at bcm2835_firmware_property+0x4c
#6 0xffff00000092811c at rpi_fw_gpio_pin_set+0xf8
#7 0xffff0000001d8488 at led_create_state+0x15c
#8 0xffff00000019eea4 at gpioled_attach+0x290
#9 0xffff0000004e4bf4 at device_attach+0x3f4
#10 0xffff0000004e4764 at device_probe_and_attach+0x80
#11 0xffff0000004e6cb8 at bus_generic_new_pass+0x100
#12 0xffff0000004e6c68 at bus_generic_new_pass+0xb0
#13 0xffff0000004e6c68 at bus_generic_new_pass+0xb0
#14 0xffff0000004e15e4 at bus_set_pass+0x50
#15 0xffff00000042a5dc at mi_startup+0x1e0
#16 0xffff0000000008a8 at virtdone+0x68
simplebus3: <v3d@7ec04000> mem 0x7ec00000-0x7ec03fff,0x7ec04000-0x7ec07fff irq 90 disabled compat brcm,2711-v3d (no driver attached)
crypto: assign cryptosoft0 driver id 0, flags 0x6000000
armv8crypto0: CPU lacks AES instructions
Device configuration finished.
procfs registered
Timecounters tick every 1.000 msec
lo0: bpf attached
vlan: initialized, using hash tables with chaining
IPsec: Initialized Security Association Processing.
tcp_init: net.inet.tcp.tcbhashsize auto tuned to 65536
usb_needs_explore_all: no devclass
sdhci_bcm0-slot0: Divider 313 for freq 399361 (base 250000000)
mmc0: Probing bus
sdhci_bcm0-slot0: Got command interrupt 0x00030000, but there is no active command.
sdhci_bcm0-slot0: ============== REGISTER DUMP ==============
sdhci_bcm0-slot0: Sys addr: 0x00000000 | Version: 0x00009902
sdhci_bcm0-slot0: Blk size: 0x00000000 | Blk cnt: 0x00000000
sdhci_bcm0-slot0: Argument: 0x000001aa | Trn mode: 0x00000000
sdhci_bcm0-slot0: Present: 0x000f0000 | Host ctl: 0x00000001
sdhci_bcm0-slot0: Power: 0x0000000f | Blk gap: 0x00000000
sdhci_bcm0-slot0: Wake-up: 0x00000000 | Clock: 0x00003947
sdhci_bcm0-slot0: Timeout: 0x00000000 | Int stat: 0x00000000
sdhci_bcm0-slot0: Int enab: 0x01ff00bb | Sig enab: 0x01ff00bb
sdhci_bcm0-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000
sdhci_bcm0-slot0: Caps: 0x00000000 | Caps2: 0x00000000
sdhci_bcm0-slot0: Max curr: 0x00000001 | ADMA err: 0x00000000
sdhci_bcm0-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000
sdhci_bcm0-slot0: ===========================================
sdhci_bcm0-slot0: Got command interrupt 0x00030000, but there is no active command.
sdhci_bcm0-slot0: ============== REGISTER DUMP ==============
sdhci_bcm0-slot0: Sys addr: 0x00000000 | Version: 0x00009902
sdhci_bcm0-slot0: Blk size: 0x00000000 | Blk cnt: 0x00000000
sdhci_bcm0-slot0: Argument: 0x000001aa | Trn mode: 0x00000000
sdhci_bcm0-slot0: Present: 0x000f0000 | Host ctl: 0x00000001
sdhci_bcm0-slot0: Power: 0x0000000f | Blk gap: 0x00000000
sdhci_bcm0-slot0: Wake-up: 0x00000000 | Clock: 0x00003947
sdhci_bcm0-slot0: Timeout: 0x00000000 | Int stat: 0x00000000
sdhci_bcm0-slot0: Int enab: 0x01ff00bb | Sig enab: 0x01ff00bb
sdhci_bcm0-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000
sdhci_bcm0-slot0: Caps: 0x00000000 | Caps2: 0x00000000
sdhci_bcm0-slot0: Max curr: 0x00000001 | ADMA err: 0x00000000
sdhci_bcm0-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000
sdhci_bcm0-slot0: ===========================================
sdhci_bcm0-slot0: Got command interrupt 0x00030000, but there is no active command.
sdhci_bcm0-slot0: ============== REGISTER DUMP ==============
sdhci_bcm0-slot0: Sys addr: 0x00000000 | Version: 0x00009902
sdhci_bcm0-slot0: Blk size: 0x00000000 | Blk cnt: 0x00000000
sdhci_bcm0-slot0: Argument: 0x000001aa | Trn mode: 0x00000000
sdhci_bcm0-slot0: Present: 0x000f0000 | Host ctl: 0x00000001
sdhci_bcm0-slot0: Power: 0x0000000f | Blk gap: 0x00000000
sdhci_bcm0-slot0: Wake-up: 0x00000000 | Clock: 0x00003947
sdhci_bcm0-slot0: Timeout: 0x00000000 | Int stat: 0x00000000
sdhci_bcm0-slot0: Int enab: 0x01ff00bb | Sig enab: 0x01ff00bb
sdhci_bcm0-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000
sdhci_bcm0-slot0: Caps: 0x00000000 | Caps2: 0x00000000
sdhci_bcm0-slot0: Max curr: 0x00000001 | ADMA err: 0x00000000
sdhci_bcm0-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000
sdhci_bcm0-slot0: ===========================================
sdhci_bcm0-slot0: Got command interrupt 0x00030000, but there is no active command.
sdhci_bcm0-slot0: ============== REGISTER DUMP ==============
sdhci_bcm0-slot0: Sys addr: 0x00000000 | Version: 0x00009902
sdhci_bcm0-slot0: Blk size: 0x00000000 | Blk cnt: 0x00000000
sdhci_bcm0-slot0: Argument: 0x000001aa | Trn mode: 0x00000000
sdhci_bcm0-slot0: Present: 0x000f0000 | Host ctl: 0x00000001
sdhci_bcm0-slot0: Power: 0x0000000f | Blk gap: 0x00000000
sdhci_bcm0-slot0: Wake-up: 0x00000000 | Clock: 0x00003947
sdhci_bcm0-slot0: Timeout: 0x00000000 | Int stat: 0x00000000
sdhci_bcm0-slot0: Int enab: 0x01ff00bb | Sig enab: 0x01ff00bb
sdhci_bcm0-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000
sdhci_bcm0-slot0: Caps: 0x00000000 | Caps2: 0x00000000
sdhci_bcm0-slot0: Max curr: 0x00000001 | ADMA err: 0x00000000
sdhci_bcm0-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000
sdhci_bcm0-slot0: ===========================================
sdhci_bcm0-slot0: Got command interrupt 0x00030000, but there is no active command.
sdhci_bcm0-slot0: ============== REGISTER DUMP ==============
sdhci_bcm0-slot0: Sys addr: 0x00000000 | Version: 0x00009902
sdhci_bcm0-slot0: Blk size: 0x00000000 | Blk cnt: 0x00000000
sdhci_bcm0-slot0: Argument: 0x00000000 | Trn mode: 0x00000000
sdhci_bcm0-slot0: Present: 0x000f0000 | Host ctl: 0x00000001
sdhci_bcm0-slot0: Power: 0x0000000f | Blk gap: 0x00000000
sdhci_bcm0-slot0: Wake-up: 0x00000000 | Clock: 0x00003947
sdhci_bcm0-slot0: Timeout: 0x00000000 | Int stat: 0x00000000
sdhci_bcm0-slot0: Int enab: 0x01ff00bb | Sig enab: 0x01ff00bb
sdhci_bcm0-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000
sdhci_bcm0-slot0: Caps: 0x00000000 | Caps2: 0x00000000
sdhci_bcm0-slot0: Max curr: 0x00000001 | ADMA err: 0x00000000
sdhci_bcm0-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000
sdhci_bcm0-slot0: ===========================================
sdhci_bcm0-slot0: Got command interrupt 0x00030000, but there is no active command.
sdhci_bcm0-slot0: ============== REGISTER DUMP ==============
sdhci_bcm0-slot0: Sys addr: 0x00000000 | Version: 0x00009902
sdhci_bcm0-slot0: Blk size: 0x00000000 | Blk cnt: 0x00000000
sdhci_bcm0-slot0: Argument: 0x00000000 | Trn mode: 0x00000000
sdhci_bcm0-slot0: Present: 0x000f0000 | Host ctl: 0x00000001
sdhci_bcm0-slot0: Power: 0x0000000f | Blk gap: 0x00000000
sdhci_bcm0-slot0: Wake-up: 0x00000000 | Clock: 0x00003947
sdhci_bcm0-slot0: Timeout: 0x00000000 | Int stat: 0x00000000
sdhci_bcm0-slot0: Int enab: 0x01ff00bb | Sig enab: 0x01ff00bb
sdhci_bcm0-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000
sdhci_bcm0-slot0: Caps: 0x00000000 | Caps2: 0x00000000
sdhci_bcm0-slot0: Max curr: 0x00000001 | ADMA err: 0x00000000
sdhci_bcm0-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000
sdhci_bcm0-slot0: ===========================================
sdhci_bcm0-slot0: Got command interrupt 0x00030000, but there is no active command.
sdhci_bcm0-slot0: ============== REGISTER DUMP ==============
sdhci_bcm0-slot0: Sys addr: 0x00000000 | Version: 0x00009902
sdhci_bcm0-slot0: Blk size: 0x00000000 | Blk cnt: 0x00000000
sdhci_bcm0-slot0: Argument: 0x00000000 | Trn mode: 0x00000000
sdhci_bcm0-slot0: Present: 0x000f0000 | Host ctl: 0x00000001
sdhci_bcm0-slot0: Power: 0x0000000f | Blk gap: 0x00000000
sdhci_bcm0-slot0: Wake-up: 0x00000000 | Clock: 0x00003947
sdhci_bcm0-slot0: Timeout: 0x00000000 | Int stat: 0x00000000
sdhci_bcm0-slot0: Int enab: 0x01ff00bb | Sig enab: 0x01ff00bb
sdhci_bcm0-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000
sdhci_bcm0-slot0: Caps: 0x00000000 | Caps2: 0x00000000
sdhci_bcm0-slot0: Max curr: 0x00000001 | ADMA err: 0x00000000
sdhci_bcm0-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000
sdhci_bcm0-slot0: ===========================================
mmc0: SD probe: failed
mmc0: MMC probe: failed
mmc0: Current OCR: 0x00000000
mmc0: No compatible cards found on bus
iicbus0: <OFW I2C bus> on iichb0
iic0: <I2C generic I/O> on iicbus0
sdhci_bcm1-slot0: Divider 125 for freq 400000 (base 100000000)
mmc1: Probing bus
mmc1: SD probe: failed
mmc1: MMC probe: OK (OCR: 0x40ff8080)
mmc1: Current OCR: 0x00ff8080
mmc1: Probing cards
mmc1: New card detected (CID 150100424a5444345203b99d4ea47800)
mmc1: New card detected (CSD d02701320f5903fff6dbffef8e404000)
mmc1: Card at relative address 0x0002 added:
mmc1: card: MMCHC BJTD4R 0.3 SN B99D4EA4 MFG 07/2021 by 21 0x0000
mmc1: quirks: 0
mmc1: bus: 8bit, 200MHz (HS400 with enhanced strobe timing)
mmc1: memory: 61071360 blocks, erase sector 1024 blocks
mmc1: setting transfer rate to 52.000MHz (high speed timing)
sdhci_bcm1-slot0: Divider 1 for freq 50000000 (base 100000000)
mmc1: setting bus width to 8 bits high speed timing
mmcsd0: taking advantage of TRIM
mmcsd0: cache size 65536KB
mmcsd0: 31GB <MMCHC BJTD4R 0.3 SN B99D4EA4 MFG 07/2021 by 21 0x0000> at mmc1 50.0MHz/8bit/65535-block
mmcsd0boot0: 4MB partition 1 at mmcsd0
mmcsd0boot1: 4MB partition 2 at mmcsd0
mmcsd0rpmb: 4MB partition 3 at mmcsd0
GEOM: new disk mmcsd0
GEOM: new disk mmcsd0boot0
GEOM: new disk mmcsd0boot1
bcm2835_cpufreq0: Boot settings:
bcm2835_cpufreq0: current ARM 600MHz, Core 200MHz, SDRAM 400MHz, Turbo OFF
bcm2835_cpufreq0: max/min ARM 1500/600MHz, Core 500/200MHz, SDRAM 400/400MHz
bcm2835_cpufreq0: current Core 850mV, SDRAM_C 1100mV, SDRAM_I 1100mV, SDRAM_P 1100mV
bcm2835_cpufreq0: max/min Core 880/880mV, SDRAM_C 1100/1100mV, SDRAM_I 1100/1100mV, SDRAM_P 1100/1100mV
bcm2835_cpufreq0: Temperature 35.0C
nvme0: Allocated 200MB host memory buffer
pci0: driver added
pci1: driver added
CPU 0: ARM Cortex-A72 r0p3 affinity: 0
Cache Type = <64 byte D-cacheline,64 byte I-cacheline,PIPT ICache,64 byte ERG,64 byte CWG>
Instruction Set Attributes 0 = <CRC32>
Instruction Set Attributes 1 = <>
Instruction Set Attributes 2 = <>
Processor Features 0 = <AdvSIMD,FP,EL3 32,EL2 32,EL1 32,EL0 32>
Trying to mount root from nfs:192.168.2.143:/root/tftpboot [rw]...
Processor Features 1 = <>
Memory Model Features 0 = <TGran4,TGran64,SNSMem,BigEnd,16bit ASID,16TB PA>
Memory Model Features 1 = <8bit VMID>
Memory Model Features 2 = <32bit CCIDX,48bit VA>
Debug Features 0 = <DoubleLock,2 CTX BKPTs,4 Watchpoints,6 Breakpoints,PMUv3,Debugv8>
Debug Features 1 = <>
Auxiliary Features 0 = <>
Auxiliary Features 1 = <>
AArch32 Instruction Set Attributes 5 = <CRC32,SEVL>
AArch32 Media and VFP Features 0 = <FPRound,FPSqrt,FPDivide,DP VFPv3+v4,SP VFPv3+v4,AdvSIMD>
AArch32 Media and VFP Features 1 = <SIMDFMAC,FPHP DP Conv,SIMDHP SP Conv,SIMDSP,SIMDInt,SIMDLS,FPDNaN,FPFtZ>
L1 cache: 48KB (instruction), 32KB (data)
L2 cache: 1024KB (unified)
CPU 1: ARM Cortex-A72 r0p3 affinity: 1
L1 cache: 48KB (instruction), 32KB (data)
L2 cache: 1024KB (unified)
CPU 2: ARM Cortex-A72 r0p3 affinity: 2
L1 cache: 48KB (instruction), 32KB (data)
L2 cache: 1024KB (unified)
CPU 3: ARM Cortex-A72 r0p3 affinity: 3
L1 cache: 48KB (instruction), 32KB (data)
L2 cache: 1024KB (unified)
gic0: using for IPIs
Release APs...nda0 at nvme0 bus 0 scbus0 target 0 lun 1
nda0: <WDC WDS250G2B0C-00PXH0 211070WD 20251C807274>
nda0: [_SERIAL_NUMBER_XXXXXXXXXXXXX]
nda0: nvme version 1.4
nda0: 238475MB (488397168 512 byte sectors)
TCP_ratelimit: Is now initialized
pass0 at nvme0 bus 0 scbus0 target 0 lun 1
pass0: <WDC WDS250G2B0C-00PXH0 211070WD 20251C807274>
pass0: [_SERIAL_NUMBER_XXXXXXXXXXXXX]: WITNESS option enabled, expect reduced performance.
274
pass0: nvme version 1.4
regulator: shutting down unused regulators
regulator: shutting down cam-dummy-reg... ok
GEOM: new disk nda0
genet0: link state changed to DOWN
NFS ROOT:[_IP_XXXXXXXX]:/root/tftpboot/
genet0: link state changed to UP
Warning: no time-of-day clock registered, system time will not be set accurately
Warning: no time-of-day clock registered, system time will not be set accurately
Dual Console: Serial Primary, Video Secondary
start_init: trying /sbin/init
Interface genet0 IP-Address[_IP_XXXXXX] Broadcast[_IP_XXXXXXXX]
No suitable dump device was found.
Setting hostuuid: 30303031-3030-3030-3633-356236616461.
Setting hostid: 0xa28b03b3.
Starting file system checks:
Mounting local filesystems:.
ELF ldconfig path: /lib /usr/lib /usr/lib/compat
32-bit compatibility ldconfig path: /usr/lib32
Setting hostname: nvme_pcie_test.
Setting up harvesting: [CALLOUT],[UMA],[FS_ATIME],SWI,INTERRUPT,NET_NG,[NET_ETHER],NET_TUN,MOUSE,KEYBOARD,ATTACH,CACHED
Feeding entropy: .
lo0: link state changed to UP
Starting Network: lo0 genet0.
lo0: flags=1008049<UP,LOOPBACK,RUNNING,MULTICAST,LOWER_UP> metric 0 mtu 16384
options=680003<RXCSUM,TXCSUM,LINKSTATE,RXCSUM_IPV6,TXCSUM_IPV6>
inet[_IP_XXXX] netmask 0xff000000
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x2
groups: lo
nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
genet0: flags=1008843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST,LOWER_UP> metric 0 mtu 1500
options=68000b<RXCSUM,TXCSUM,VLAN_MTU,LINKSTATE,RXCSUM_IPV6,TXCSUM_IPV6>
ether [_MAC_XXXXXXXXXX]
inet[_IP_XXXXXX] netmask 0xffffff00 broadcast[_IP_XXXXXXXX]
media: Ethernet autoselect (1000baseT <full-duplex>)
status: active
nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL>
Starting devd.
Starting dhclient.
Cannot open or create pidfile: No locks available
can't open and lock /var/db/dhclient.leases.genet0: No locks available
exiting.
/etc/rc.d/dhclient: WARNING: failed to start dhclient
devd: cannot open pid file: No locks available
route: message indicates error: File exists
add host[_IP_XXXX]: gateway lo0 fib 0: route already in table
route: message indicates error: File exists
add host ::1: gateway lo0 fib 0: route already in table
add net fe80::: gateway ::1
add net ff02::: gateway ::1
add net ::ffff:0.0.0.0: gateway ::1
add net ::0.0.0.0: gateway ::1
Mounting NFS filesystems:.
ELF ldconfig path: /lib /usr/lib /usr/lib/compat
32-bit compatibility ldconfig path: /usr/lib32
Updating /var/run/os-release done.
Clearing /tmp (X related).
Updating motd:.
Creating and/or trimming log files.
Starting syslogd.
syslogd: cannot open pid file: No locks available
protect: option requires an argument -- p
usage: protect [-i] command
protect [-cdi] -g pgrp | -p pid
Setting date via ntp.
Error resolving 0.freebsd.pool.ntp.org: Name does not resolve (8)
1 Jan 00:00:23 ntpdate[1353]: Can't find host 0.freebsd.pool.ntp.org: Name does not resolve (8)
Error resolving 2.freebsd.pool.ntp.org: Name does not resolve (8)
1 Jan 00:00:23 ntpdate[1353]: Can't find host 2.freebsd.pool.ntp.org: Name does not resolve (8)
1 Jan 00:00:23 ntpdate[1353]: no servers can be used, exiting
Starting rpcbind.
Starting statd.
Starting lockd.
Mounting late filesystems:.
Starting cron.
Performing sanity check on sshd configuration.
Starting sshd.
Starting background file system checks in 60 seconds.
Thu Jan 1 00:00:25 UTC 1970
FreeBSD/arm64 (nvme_pcie_test) (ttyu0)
login: root
Last login: Thu Jan 1 00:00:30 on ttyu0
FreeBSD 15.0-CURRENT (GENERIC) #4 main-n269491-f276adc14843-dirty: Thu Apr 18 07:14:34 CEST 2024
Welcome to FreeBSD!
Release Notes, Errata: https://www.FreeBSD.org/releases/
Security Advisories: https://www.FreeBSD.org/security/
FreeBSD Handbook: https://www.FreeBSD.org/handbook/
FreeBSD FAQ: https://www.FreeBSD.org/faq/
Questions List: https://www.FreeBSD.org/lists/questions/
FreeBSD Forums: https://forums.FreeBSD.org/
Documents installed with the system are in the /usr/local/share/doc/freebsd/
directory, or can be installed later with: pkg install en-freebsd-doc
For other languages, replace "en" with a language code like de or fr.
Show the version of FreeBSD installed: freebsd-version ; uname -a
Please include that output and any error messages when posting questions.
Introduction to manual pages: man man
FreeBSD directory layout: man hier
To change this login announcement, see motd(5).
root@nvme_pcie_test:~ # Jan 1 00:00:30 nvme_pcie_test login[1562]: ROOT LOGIN (root) ON ttyu0
root@nvme_pcie_test:~ # nvmecontrol devlist
nvme0: WDC WDS250G2B0C-00PXH0
nvme0ns1 (238475MB)
root@nvme_pcie_test:~ # gpart show
=> 63 61071297 mmcsd0 MBR (29G)
63 1985 - free - (993K)
2048 102400 1 fat32lba [active] (50M)
104448 60966912 2 freebsd (29G)
=> 0 60966912 mmcsd0s2 BSD (29G)
0 128 - free - (64K)
128 54853504 1 freebsd-ufs (26G)
54853632 6111232 2 freebsd-swap (2.9G)
60964864 2048 - free - (1.0M)
=> 63 61071297 diskid/DISK-B99D4EA4 MBR (29G)
63 1985 - free - (993K)
2048 102400 1 fat32lba [active] (50M)
104448 60966912 2 freebsd (29G)
=> 0 60966912 diskid/DISK-B99D4EA4s2 BSD (29G)
0 128 - free - (64K)
128 54853504 1 freebsd-ufs (26G)
54853632 6111232 2 freebsd-swap (2.9G)
60964864 2048 - free - (1.0M)
=> 40 488397088 nda0 GPT (233G)
40 532480 1 efi (260M)
532520 1024 2 freebsd-boot (512K)
533544 984 - free - (492K)
534528 4194304 3 freebsd-swap (2.0G)
4728832 483667968 4 freebsd-zfs (231G)
488396800 328 - free - (164K)
=> 40 488397088 diskid/DISK-20251C807274 GPT (233G)
40 532480 1 efi (260M)
532520 1024 2 freebsd-boot (512K)
533544 984 - free - (492K)
534528 4194304 3 freebsd-swap (2.0G)
4728832 483667968 4 freebsd-zfs (231G)
488396800 328 - free - (164K)