Launched in 2004, dmesgd aims to provide a user-submitted repository of searchable *BSD dmesgs. The dmesg(8) command displays the system message buffer's content, and during boot a copy is saved to /var/run/dmesg.boot. This buffer contains the operating system release, name and version, a list of devices identified, plus a whole host of other useful information. We hope others find this resource useful and further contribute to its growth. Contact us at [ admin at lists dot nycbug dot org ]. Note that this site is not a substitute for sending the dmesg directly to the respective project.
Date: 2024-05-01 08:19:50
From: yamori813
Description: Fon_FON2305E_FDT intr v1 typo fixed
---<<BOOT>>---
KDB: debugger backends: ddb
KDB: current backend: ddb
Copyright (c) 1992-2021 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 12.4-STABLE zrouter_yamori813-n234881-f2f14b901f48 Fon_FON2305E_FDT mips
gcc version 4.2.1 20070831 patched [FreeBSD]
Preloaded elf kernel "kernel" at 0x8036cb00.
CPU: MIPS Technologies (RT3350 ) processor v76.150
MMU: Standard TLB, 32 entries (4K 16K 64K 256K 1M 16M 64M 256M pg sizes)
L1 i-cache: 4 ways of 256 sets, 32 bytes per line
L1 d-cache: 4 ways of 128 sets, 32 bytes per line
L2 cache: disabled
Config1=0xbea3319e<PerfCount,WatchRegs,MIPS16,EJTAG>
Config2=0x80000000
Config3=0x420<DSPP,VInt>
Config7=0x0
real memory = 33554432 (32768K bytes)
Physical memory chunk(s):
0x00405000 - 0x01f7efff, 28811264 bytes (7034 pages)
avail memory = 28196864 (26MB)
random: no preloaded entropy cache
arc4random: WARNING: initial seeding bypassed the cryptographic random device because it was not yet seeded and the knob 'bypass_before_seeding' was enabled.
hostuuid: using 00000000-0000-0000-0000-000000000000
ULE: setup cpu 0
random: entropy device external interface
WARNING: Device "g_ctl" is Giant locked and may be deleted before FreeBSD 14.0.
null: <full device, null device, zero device>
openfirm: <Open Firmware control device>
WARNING: Device "openfirm" is Giant locked and may be deleted before FreeBSD 14.0.
mem: <memory>
nexus0: <MIPS32 root nexus>
ofwbus0: <Open Firmware Device Tree> on nexus0
palmbus0: <MTK Palmbus> mem 0x10000000-0x101fffff on ofwbus0
cpupic0: <MIPS32 Interrupt Controller> on ofwbus0
sysc0: <MTK System Controller> mem 0-0xff on palmbus0
mtk_wdog0: <MTK WatchDog(Timer1) Controller (v1)> mem 0x120-0x12f irq 5 on palmbus0
pinctrl0: <MTK Pin Controller> on ofwbus0
pinctrl0: GPIO mode start: 0x0000029d
Processing 1 pin-config node(s) in pinctrl-0 for spi@b00
Processing 1 pin-config node(s) in pinctrl-0 for uartlite@c00
Processing 1 pin-config node(s) in pinctrl-0 for pinctrl
pinctrl0: GPIO mode end : 0x000002dd
rstctrl0: <MTK Reset Controller> on ofwbus0
clkctrl0: <MTK Clock Controller> on ofwbus0
intc0: <MTK Interrupt Controller (v1)> mem 0x200-0x2ff irq 6 on palmbus0
gpio0: <MTK GPIO Controller (v1)> mem 0x600-0x633 irq 9 on palmbus0
gpiobus0: <OFW GPIO bus> on gpio0
cpulist0: <Open Firmware CPU Group> on ofwbus0
palmbus0: <timer@100> mem 0x100-0x11f irq 4 compat ralink,rt3050-timer (no driver attached)
palmbus0: <memc@300> mem 0x300-0x3ff irq 7 compat ralink,rt3050-memc (no driver attached)
palmbus0: <uart@500> mem 0x500-0x5ff irq 8 disabled compat ralink,rt3050-uart (no driver attached)
gpioc0: <GPIO controller> on gpio0
palmbus0: <gpio@638> mem 0x638-0x65b disabled compat ralink,rt3050-gpio (no driver attached)
palmbus0: <gpio@660> mem 0x660-0x683 disabled compat ralink,rt3050-gpio (no driver attached)
spi0: <MTK SPI Controller (v1)> mem 0xb00-0xbff on palmbus0
spi0: Warning: No cs-gpios specified in fdt data; device may not function.
spibus0: <OFW SPI bus> on spi0
mx25l0: <M25Pxx Flash Family> at cs 0 mode 0 on spibus0
mx25l0: device type mx25ll64, size 8192K in 128 sectors of 64K, erase size 64K
uart0: <MTK UART Controller> mem 0xc00-0xcff irq 10 on palmbus0
uart0: console (57971,n,8,1)
uart0: fast interrupt
uart0: PPS capture mode: DCD
ofwbus0: <usbphy> compat ralink,rt3050-usbphy (no driver attached)
rt0: <Ralink RT3050 onChip Ethernet driver> mem 0x10100000-0x1010ffff irq 0 on ofwbus0
rt0: RT305XF Ethernet MAC (rev 0x00000000)
rt0: use hardcoded [_MAC_XXXXXXXXXX] macaddr
rt0: bpf attached
rt0: Ethernet address: [_MAC_XXXXXXXXXX]
mtkswitch0: <MTK Switch Driver> mem 0x10110000-0x10117fff irq 1 on ofwbus0
miibus0: <MII bus> on mtkswitch0
ukphy0: <Generic IEEE 802.3u media interface> PHY 0 on miibus0
ukphy0: OUI 0x000c43, model 0x0001, rev. 7
ukphy0: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
miibus1: <MII bus> on mtkswitch0
ukphy1: <Generic IEEE 802.3u media interface> PHY 1 on miibus1
ukphy1: OUI 0x000c43, model 0x0001, rev. 7
ukphy1: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
miibus2: <MII bus> on mtkswitch0
ukphy2: <Generic IEEE 802.3u media interface> PHY 2 on miibus2
ukphy2: OUI 0x000c43, model 0x0001, rev. 7
ukphy2: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
miibus3: <MII bus> on mtkswitch0
ukphy3: <Generic IEEE 802.3u media interface> PHY 3 on miibus3
ukphy3: OUI 0x000c43, model 0x0001, rev. 7
ukphy3: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
miibus4: <MII bus> on mtkswitch0
ukphy4: <Generic IEEE 802.3u media interface> PHY 4 on miibus4
ukphy4: OUI 0x000c43, model 0x0001, rev. 7
ukphy4: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
etherswitch0: <Switch controller> on mtkswitch0
mdio0: <MDIO> on mtkswitch0
ofwbus0: <wmac@10180000> mem 0x10180000-0x101bffff irq 2 compat ralink,rt3050-wmac (no driver attached)
ofwbus0: <otg@101c0000> mem 0x101c0000-0x101fffff irq 3 compat ralink,rt3050-otg (no driver attached)
ofwbus0: <cfi@1f000000> mem 0x1f000000-0x1f3fffff compat cfi-flash (no driver attached)
gpioled0: <GPIO LEDs> on ofwbus0
ofwbus0: <gpio-keys-polled> compat gpio-keys-polled (no driver attached)
clock0: <Generic MIPS32 ticker> on nexus0
Timecounter "MIPS32" frequency 160000000 Hz quality 800
Event timer "MIPS32" frequency 160000000 Hz quality 800
Device configuration finished.
Timecounters tick every 10.000 msec
vlan: initialized, using hash tables with chaining
lo0: bpf attached
tcp_init: net.inet.tcp.tcbhashsize auto tuned to 512
mtkswitch0port0: link state changed to DOWN
mtkswitch0port1: link state changed to DOWN
mtkswitch0port2: link state changed to DOWN
mtkswitch0port3: link state changed to DOWN
mtkswitch0port4: link state changed to DOWN
GEOM: new disk flash/spi0
Trying to mount root from cd9660:/dev/flash/spi0s.rootfs.uzip []...
flash/spi0: slice 00000000-0000ffff: u-boot (63KB)
flash/spi0: slice 00010000-0001ffff: u-boot-env (63KB)
flash/spi0: slice 00020000-0011ffff: kernel (1023KB)
flash/spi0: slice 00120000-007fffff: rootfs (7039KB)
flash/spi0: slice 00020000-007fffff: upgrade (8063KB)
cd9660: RockRidge Extension
Warning: no time-of-day clock registered, system time will not be set accurately
Dual Console: Serial Primary, Video Secondary
start_init: trying /sbin/init
mtkswitch0port2: link state changed to UP
random: unblocking device.
lo0: link state changed to UP
/tmp: optimization changed from SPACE to TIME