Launched in 2004, dmesgd aims to provide a user-submitted repository of searchable *BSD dmesgs. The dmesg(8) command displays the system message buffer's content, and during boot a copy is saved to /var/run/dmesg.boot. This buffer contains the operating system release, name and version, a list of devices identified, plus a whole host of other useful information. We hope others find this resource useful and further contribute to its growth. Contact us at [ admin at lists dot nycbug dot org ]. Note that this site is not a substitute for sending the dmesg directly to the respective project.
Date: 2025-10-14 12:58:14
From: Ken Wellsch
Description: OpenBSD/sgi 6.9 on SGI Indigo2
System Maintenance Menu
1) Start System
2) Install System Software
3) Run Diagnostics
4) Recover System
5) Enter Command Monitor
Option? 5
Command Monitor. Type "exit" to return to the menu.
>> scsi(1)disk(2)rdisk(0)partition(8)boot scsi(1)disk(2)partition(0)bsd
1024+43584+4368+1696+400 entry: 0x900000003fff2d80
OpenBSD/sgi-IP28 ARCBios boot version 1.13
arg 0: scsi(1)disk(2)rdisk(0)partition(8)boot
arg 1: scsi(1)disk(2)partition(0)bsd
arg 2: ConsoleIn=serial(0)
arg 3: ConsoleOut=serial(0)
arg 4: OSLoader=boot64
arg 5: OSLoadFilename=bsd
Boot: scsi(1)disk(2)partition(0)bsd
cannot open /etc/random.seed: Device not configured
4110384+795104 [97+88+265680+161272]=0x516198
ARCS64 Firmware
Found SGI-IP28, setting up.
Initial setup done, switching console.
[ using 427912 bytes of bsd ELF symbol table ]
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2021 OpenBSD. All rights reserved. https://www.OpenBSD.org
OpenBSD 6.9 (GENERIC-IP28) #0: Thu Apr 22 04:29:15 UTC 2021
[_EMAIL_XXXXXXX]:/usr/src/sys/arch/sgi/compile/GENERIC-IP28
real mem = 536870912 (512MB)
rsvd mem = 1064960 (2MB)
avail mem = 525434880 (501MB)
random: boothowto does not indicate good seed
mainbus0 at root: POWER Indigo2 R10000
cpu0 at mainbus0: MIPS R10000 CPU rev 2.5 174 MHz, R10000 FPU rev 0.0
cpu0: cache L1-I 32KB D 32KB 2 way, L2 1024KB 2 way
int0 at mainbus0 addr 0x1fbd9000
imc0 at mainbus0: revision 5
gio0 at imc0
impact0 at gio0 addr 0x1f000000: Solid Impact
impact0: device has not been setup by firmware!
hpc0 at gio0 addr 0x1fb80000: SGI HPC3 (onboard)
zs0 at hpc0 offset 0x00059830 irq 29: 85230
zstty0 at zs0 channel 1: console
zstty1 at zs0 channel 0
pckbc0 at hpc0 offset 0x00059840 irq 28
sq0 at hpc0 offset 0x00054000 irq 3: Seeq 80c03, address [_MAC_XXXXXXXXXX]
wdsc0 at hpc0 offset 0x00044000 irq 1: WD33C93B, 20.0 MHz, burst DMA
wdsc0: microcode revision 0x0d, fast SCSI
scsibus0 at wdsc0: 8 targets, initiator 0
sd0 at scsibus0 targ 3 lun 0: <TOSHIBA, CD-ROM XM-5401TA, 0436>
wdsc1 at hpc0 offset 0x0004c000 irq 2: WD33C93B, 20.0 MHz, burst DMA
wdsc1: microcode revision 0x0d, fast SCSI
scsibus1 at wdsc1: 8 targets, initiator 0
sd1 at scsibus1 targ 2 lun 0: <ZULUSCSI, HARDDRIVE, 2.3B> serial.ZULUSCSIHARDDRIVE_42F55FF8
sd1: 4095MB, 512 bytes/sector, 8386560 sectors
cd0 at scsibus1 targ 5 lun 0: <ZULUSCSI, CDROM, 2.3B> removable serial.ZULUSCSICDROM_42F55FF8
haltwo at hpc0 offset 0x00058000 irq 12 not configured
pione at hpc0 offset 0x00059800 irq 5 not configured
panel0 at hpc0 offset 0x00059850 irq 9: power button
dsclock0 at hpc0 offset 0x00060000
eisa0 at imc0 irq 27
vscsi0 at root
scsibus2 at vscsi0: 256 targets
softraid0 at root
scsibus3 at softraid0: 256 targets
boot device: 'unknown' unrecognized.
disklabels not read: sd0 sd1 cd0
root device: sd1
swap device (default sd1b):
root on sd1a swap on sd1b dump on sd1b
Automatic boot in progress: starting file system checks.
/dev/sd1a (aa92aec62ef1ca33.a): file system is clean; not checking
/dev/sd1e (aa92aec62ef1ca33.e): file system is clean; not checking
/dev/sd1d (aa92aec62ef1ca33.d): file system is clean; not checking
pf enabled
starting network
sq0:[_IP_XXXXXXXXX] lease accepted from[_IP_XXXXXXX] ([_MAC_XXXXXXXXXX])
reordering libraries: done.
starting early daemons: syslogd pflogd ntpd.
starting RPC daemons:.
savecore: no core dump
checking quotas: done.
clearing /tmp
kern.securelevel: 0 -> 1
creating runtime link editor directory cache.
preserving editor files.
starting network daemons: sshd smtpd sndiod.
starting local daemons: cron.
Tue Oct 14 08:55:12 EDT 2025
OpenBSD/sgi (indigo2.localhost) (console)
login: root
Password:
Last login: Thu Apr 22 06:24:26 on console
OpenBSD 6.9 (GENERIC-IP28) #0: Thu Apr 22 04:29:15 UTC 2021
Welcome to OpenBSD: The proactively secure Unix-like operating system.
Please use the sendbug(1) utility to report bugs in the system.
Before reporting a bug, please try to reproduce it with the latest
version of the code. With bug reports, please try to ensure that
enough information to reproduce the problem is enclosed, and if a
known fix for it exists, include that as well.
You have mail.
indigo2# dd if=/dev/rsd1c of=/dev/null bs=1m count=100
100+0 records in
100+0 records out
104857600 bytes transferred in 44.376 secs (2362934 bytes/sec)