Launched in 2004, dmesgd aims to provide a user-submitted repository of searchable *BSD dmesgs. The dmesg(8) command displays the system message buffer's content, and during boot a copy is saved to /var/run/dmesg.boot. This buffer contains the operating system release, name and version, a list of devices identified, plus a whole host of other useful information. We hope others find this resource useful and further contribute to its growth. Contact us at [ admin at lists dot nycbug dot org ]. Note that this site is not a substitute for sending the dmesg directly to the respective project.
Date: 2026-02-15 09:11:23
From: tsutsui
Description: NetBSD/evbarm-aarch64 11.0_RC1 on Raspberry Pi 4B
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003,
2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013,
2014, 2015, 2016, 2017, 2018, 2019, 2020, 2021, 2022, 2023,
2024, 2025, 2026
The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
NetBSD 11.0_RC1 (GENERIC64) #0: Fri Feb 6 08:24:25 UTC 2026
[_EMAIL_XXXXXXXXXXXXXXXXX]:/usr/src/sys/arch/evbarm/compile/GENERIC64
total memory = 3938 MB
avail memory = 3794 MB
timecounter: Timecounters tick every 10.000 msec
Kernelized RAIDframe activated
armfdt0 (root)
simplebus0 at armfdt0: Raspberry Pi 4 Model B Rev 1.5
simplebus1 at simplebus0
simplebus2 at simplebus0
cpus0 at simplebus0
simplebus3 at simplebus0
simplebus4 at simplebus0
cpu0 at cpus0: Arm Cortex-A72 r0p3 (v8-A), id 0x0
cpu0: package 0, core 0, smt 0, numa 0
cpu0: IC enabled, DC enabled, EL0/EL1 stack Alignment check enabled
cpu0: Cache Writeback Granule 16B, Exclusives Reservation Granule 16B
cpu0: Dcache line 64, Icache line 64, DIC=0, IDC=0, LoUU=1, LoC=2, LoUIS=1
cpu0: L1 48KB/64B 3-way (256 set) PIPT Instruction cache
cpu0: L1 32KB/64B 2-way (256 set) PIPT Data cache
cpu0: L2 1024KB/64B 16-way (1024 set) PIPT Unified cache
cpu0: revID=0x0, PMCv3, 4k table, 64k table, 16bit ASID
cpu0: auxID=0x10000, FP, CRC32, NEON, rounding, NaN propagation, denormals, 32x64bitRegs, Fused Multiply-Add
cpu1 at cpus0: Arm Cortex-A72 r0p3 (v8-A), id 0x1
cpu1: package 0, core 1, smt 0, numa 0
cpu1: IC enabled, DC enabled, EL0/EL1 stack Alignment check enabled
cpu1: Cache Writeback Granule 16B, Exclusives Reservation Granule 16B
cpu1: Dcache line 64, Icache line 64, DIC=0, IDC=0, LoUU=1, LoC=2, LoUIS=1
cpu1: L1 48KB/64B 3-way (256 set) PIPT Instruction cache
cpu1: L1 32KB/64B 2-way (256 set) PIPT Data cache
cpu1: L2 1024KB/64B 16-way (1024 set) PIPT Unified cache
cpu1: revID=0x0, PMCv3, 4k table, 64k table, 16bit ASID
cpu1: auxID=0x10000, FP, CRC32, NEON, rounding, NaN propagation, denormals, 32x64bitRegs, Fused Multiply-Add
cpu2 at cpus0: Arm Cortex-A72 r0p3 (v8-A), id 0x2
cpu2: package 0, core 2, smt 0, numa 0
cpu2: IC enabled, DC enabled, EL0/EL1 stack Alignment check enabled
cpu2: Cache Writeback Granule 16B, Exclusives Reservation Granule 16B
cpu2: Dcache line 64, Icache line 64, DIC=0, IDC=0, LoUU=1, LoC=2, LoUIS=1
cpu2: L1 48KB/64B 3-way (256 set) PIPT Instruction cache
cpu2: L1 32KB/64B 2-way (256 set) PIPT Data cache
cpu2: L2 1024KB/64B 16-way (1024 set) PIPT Unified cache
cpu2: revID=0x0, PMCv3, 4k table, 64k table, 16bit ASID
cpu2: auxID=0x10000, FP, CRC32, NEON, rounding, NaN propagation, denormals, 32x64bitRegs, Fused Multiply-Add
cpu3 at cpus0: Arm Cortex-A72 r0p3 (v8-A), id 0x3
cpu3: package 0, core 3, smt 0, numa 0
cpu3: IC enabled, DC enabled, EL0/EL1 stack Alignment check enabled
cpu3: Cache Writeback Granule 16B, Exclusives Reservation Granule 16B
cpu3: Dcache line 64, Icache line 64, DIC=0, IDC=0, LoUU=1, LoC=2, LoUIS=1
cpu3: L1 48KB/64B 3-way (256 set) PIPT Instruction cache
cpu3: L1 32KB/64B 2-way (256 set) PIPT Data cache
cpu3: L2 1024KB/64B 16-way (1024 set) PIPT Unified cache
cpu3: revID=0x0, PMCv3, 4k table, 64k table, 16bit ASID
cpu3: auxID=0x10000, FP, CRC32, NEON, rounding, NaN propagation, denormals, 32x64bitRegs, Fused Multiply-Add
gic0 at simplebus1: GIC
armgic0 at gic0: Generic Interrupt Controller, 256 sources (247 valid)
armgic0: 16 Priorities, 224 SPIs, 7 PPIs, 16 SGIs
syscon0 at simplebus1: System Controller Registers
fclock0 at simplebus2: 54000000 Hz fixed clock (osc)
bcmcprman0 at simplebus1: BCM283x Clock Controller
syscon1 at simplebus1autoconfiguration error: : couldn't get registers
bcmaux0 at simplebus1
fclock1 at simplebus2: 480000000 Hz fixed clock (otg)
fclock2 at simplebus0sysctl_createv: sysctl_create(108MHz-clock) returned 22
autoconfiguration error: fclock2: failed to create sysctl node for 108MHz-clock (108MHz-clock): 22
: 108000000 Hz fixed clock (108MHz-clock)
fclock3 at simplebus0sysctl_createv: sysctl_create(27MHz-clock) returned 22
autoconfiguration error: fclock3: failed to create sysctl node for 27MHz-clock (27MHz-clock): 22
: 27000000 Hz fixed clock (27MHz-clock)
bcmicu0 at simplebus1: Multiprocessor
gtmr0 at simplebus0: Generic Timer
gtmr0: interrupting on GIC irq 27
armgtmr0 at gtmr0: Generic Timer (54000 kHz, virtual)
timecounter: Timecounter "armgtmr0" frequency 54000000 Hz quality 500
bcmgpio0 at simplebus1: GPIO controller 2838
bcmgpio0: pins 0..31 interrupting on GIC irq 145
bcmgpio0: pins 32..58 interrupting on GIC irq 146
gpio0 at bcmgpio0: 58 pins
gregulator0 at simplebus0: vdd-sd-io
gregulator0: autoconfiguration error: cannot get pin 0
fregulator0 at simplebus0: vcc-sd
plcom0 at simplebus1: ARM PL011 UART
plcom0: txfifo 16 bytes
plcom0: interrupting on GIC irq 153
com0 at simplebus1: BCM AUX UART, 1-byte FIFO
com0: console
com0: interrupting on GIC irq 125, clock 1000000000 Hz
mmcpwrseq0 at simplebus0autoconfiguration error: : couldn't get reset GPIOs
/soc/avs-monitor@7d5d2000/thermal at syscon0 not configured
/soc/power at simplebus1 not configured
/phy at simplebus0 not configured
/soc/clock@7ef00000 at simplebus1 not configured
/soc/interrupt-controller@7ef00100 at simplebus1 not configured
/soc/i2c@7ef04500 at simplebus1 not configured
bcmdmac0 at simplebus1: DMA0 DMA2 DMA4 DMA5 DMA6 DMA7 DMA8 DMA9 DMA10
/soc/i2c@7ef09500 at simplebus1 not configured
bcmmbox0 at simplebus1: VC mailbox
bcmmbox0: interrupting on GIC irq 65
vcmbox0 at bcmmbox0
/scb/pcie@7d500000 at simplebus3 not configured
genet0 at simplebus3: GENETv5.0
genet0: Ethernet address [_MAC_XXXXXXXXXX]
brgphy0 at genet0 phy 1: BCM54213PE 1000BASE-T media interface, rev. 2
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
genet0: interrupting on GIC irq 189
/soc/timer@7e003000 at simplebus1 not configured
/soc/txp@7e004000 at simplebus1 not configured
bsciic0 at simplebus1: Broadcom Serial Controller
bsciic0: interrupting on GIC irq 149
iic0 at bsciic0: I2C bus
sdhc0 at simplebus1: SDHC controller
sdhc0: interrupting on GIC irq 158
bsciic1 at simplebus1: Broadcom Serial Controller
bsciic1: interrupting on GIC irq 149
iic1 at bsciic1: I2C bus
dwctwo0 at simplebus1: USB controller
dwctwo0: interrupting on GIC irq 105
bcmpmwdog0 at simplebus1: Power management, Reset and Watchdog controller
/soc/pixelvalve@7e206000 at simplebus1 not configured
/soc/pixelvalve@7e207000 at simplebus1 not configured
/soc/pixelvalve@7e20a000 at simplebus1 not configured
/soc/pwm@7e20c800 at simplebus1 not configured
/soc/pixelvalve@7e216000 at simplebus1 not configured
/soc/hdmi@7ef00700 at simplebus1 not configured
/soc/hdmi@7ef05700 at simplebus1 not configured
vchiq0 at simplebus1: BCM2835 VCHIQ
/gpu at simplebus0 not configured
sdhc1 at simplebus4: SDHC controller
sdhc1: interrupting on GIC irq 158
/chosen at simplebus0 not configured
armpmu0 at simplebus0: Performance Monitor Unit
gpioleds0 at simplebus0: ACT
/soc/rng@7e104000 at simplebus1 not configured
WARNING: system needs entropy for security; see entropy(7)
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
sdhc0: SDHC 3.0, rev 153, caps <01610000/00000000>, platform DMA, 250000 kHz, HS 3.3V, re-tuning mode 1, 1024 byte blocks
sdmmc0 at sdhc0 slot 0
dwctwo0: Core Release: 2.80a (snpsid=4f54280a)
usb0 at dwctwo0: USB revision 2.0
sdhc1: SDHC 3.0, rev 16, caps <01210000/00000000>, PIO, 100000 kHz, HS 3.3V, re-tuning mode 1, 1024 byte blocks
sdmmc1 at sdhc1 slot 0
uhub0 at usb0: NetBSD (0x0000) DWC2 root hub (0x0000), class 9/0, rev 2.00/1.00, addr 1
uhub0: 1 port with 1 removable, self powered
armpmu0: interrupting on GIC irq 48
armpmu0: interrupting on GIC irq 49
armpmu0: interrupting on GIC irq 50
armpmu0: interrupting on GIC irq 51
IPsec: Initialized Security Association Processing.
sdmmc1: SD card status: 4-bit, C10, U1, V10, A1
ld1 at sdmmc1: <0x02:0x544d:SA32G:0x83:0x2ba2b2a9:0x19b>
ld1: 29818 MB, 7572 cyl, 128 head, 63 sec, 512 bytes/sect x 61067264 sectors (0 bytes/physsect)
ld1: GPT GUID: 3efb4280-0335-11f1-8000-000000000000
dk0 at ld1: "EFI", 163840 blocks at 32768, type: msdos
dk1 at ld1: "netbsd-root", 60866560 blocks at 196608, type: ffs
ld1: 4-bit width, High-Speed/SDR25, 50.000 MHz
sdmmc0: 4-bit width, 50.000 MHz
sdmmc0: SDIO function
bwfm0 at sdmmc0 function 1
(manufacturer 0x2d0, product 0xa9a6) at sdmmc0 function 2 not configured
(manufacturer 0x2d0, product 0xa9a6, standard function interface code 0x2) at sdmmc0 function 3 not configured
swwdog0: software watchdog initialized
WARNING: 5 errors while detecting hardware; check system log.
boot device: ld1
root on dk1
root file system type: ffs
kern.module.path=/stand/evbarm/11.0/modules
WARNING: no TOD clock present
vchiq0: interrupting on GIC irq 66
WARNING: using filesystem time
vchiq: vchiq_init_state: slot_zero = 0xffffc001820c8000, is_master = 0
WARNING: CHECK AND RESET THE DATE!
vchiq: local ver 8 (min 3), remote ver 8.
vcaudio0 at vchiq0: auds
bwfm0: Firmware file default: brcmfmac43455-sdio.bin
bwfm0: Firmware file model-spec: brcmfmac43455-sdio.raspberrypi,4-model-b.bin
audio0 at vcaudio0: playback
audio0: slinear_le:16 -> slinear_le:16 2ch 48000Hz, blk 7680 bytes (40ms) for playback
spkr0 at audio0: PC Speaker (synthesized)
wsbell at spkr0 not configured
bwfm0: Found Firmware file: brcmfmac43455-sdio.bin
bwfm0: NVRAM file default: brcmfmac43455-sdio.txt
bwfm0: NVRAM file model-spec: brcmfmac43455-sdio.raspberrypi,4-model-b.txt
bwfm0: Found NVRAM file: brcmfmac43455-sdio.raspberrypi,4-model-b.txt
bwfm0: CLM file default: brcmfmac43455-sdio.clm_blob
bwfm0: CLM file model-spec: brcmfmac43455-sdio.raspberrypi,4-model-b.clm_blob
bwfm0: CHIPACTIVE
bwfm0: address [_MAC_XXXXXXXXXX]
bwfm0: wl0: Mar 1 2015 07:29:38 version 7.45.18 (r538002) FWID 01-6a2c8ad4
entropy: best effort