Launched in 2004, dmesgd aims to provide a user-submitted repository of searchable *BSD dmesgs. The dmesg(8) command displays the system message buffer's content, and during boot a copy is saved to /var/run/dmesg.boot. This buffer contains the operating system release, name and version, a list of devices identified, plus a whole host of other useful information. We hope others find this resource useful and further contribute to its growth. Contact us at [ admin at lists dot nycbug dot org ]. Note that this site is not a substitute for sending the dmesg directly to the respective project.
Date: 2026-02-04 09:13:25
From: yurix
Description: i.MX23-OLinuXino
NetBSD 11.99.5 (GENERIC_V5) #516: Tue Feb 3 21:50:15 CET 2026
yurix@yurix-laptop:/home/yurix/Documents/6_programming/netbsd-ev3/netbsd/src/sys/arch/evbarm/compile/obj/GENERIC_V5
total memory = 65536 KB
avail memory = 53856 KB
timecounter: Timecounters tick every 10.000 msec
Kernelized RAIDframe activated
armfdt0 (root)
simplebus0 at armfdt0: i.MX23 Olinuxino Low Cost Board
simplebus1 at simplebus0
simplebus2 at simplebus0
simplebus3 at simplebus0
cpus0 at simplebus0
cpu0 at cpus0: ARM926EJ-S r0p5 (ARM9EJ-S V5TEJ core)
cpu0: DC enabled IC enabled WB enabled LABT
cpu0: L1 16KB/32B 4-way (128 set) VIVT Instruction cache
cpu0: L1 16KB/32B 4-way (128 set) write-back-locking-C VIVT Data cache
cpu0: unrecognized VFP version 0
simplebus4 at simplebus1
simplebus5 at simplebus1
imx23icoll0 at simplebus4
imx23clkctrl0 at simplebus5
imx23apbdma0 at simplebus4: type=apbh
imx23pctl0 at simplebus4: PIN MUX & GPIO
gpio0 at imx23pctl0: 96 pins
imx23apbdma1 at simplebus4: type=apbx
imx23usbphy0 at simplebus5: USB PHY v4.0
imx23digctl0 at simplebus4
timecounter: Timecounter "digctl" frequency 1000000 Hz quality 100
imx23mmc0 at simplebus4: SSP Block v3.0
sdmmc0 at imx23mmc0
imx23rtc0 at simplebus5
imx23timrot0 at simplebus5: systimer on icoll irq 28: stattimer on icoll irq 29
plcom0 at simplebus5: ARM PL011 UART
plcom0: txfifo 16 bytes
plcom0: console
plcom0: interrupting on icoll irq 0
fregulator0 at simplebus0: usb0_vbus
imxusbc0 at simplebus2
ehci0 at imxusbc0: i.MX USB Controller
ehci0: id=5 revision=65 HCI revision=0x100
ehci0: 1 host port, device capable, 5 endpoints
ehci0: interrupting on icoll irq 11
ehci0: EHCI version 1.0
usb0 at ehci0: USB revision 2.0
imx23digfilt0 at simplebus5: DIGFILT Block v1.1.0audio0 at imx23digfilt0: playback
audio0: slinear_le:16 2ch 44100Hz, blk 2048 bytes (11.6ms) for playback
/apb@80000000/apbx-bus@80040000/lradc@80050000 at simplebus5 not configured
/apb@80000000/apbh-bus@80000000/crypto@80028000 at simplebus4 not configured
/apb@80000000/apbh-bus@80000000/spi@80034000 at simplebus4 not configured
/apb@80000000/apbx-bus@80040000/i2c@80058000 at simplebus5 not configured
/apb@80000000/apbx-bus@80040000/serial@8006c000 at simplebus5 not configured
/iio-hwmon at simplebus0 not configured
gpioleds0 at simplebus0: green
/apb@80000000/apbh-bus@80000000/efuse@8002c000 at simplebus4 not configured
WARNING: system needs entropy for security; see entropy(7)
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
uhub0 at usb0: NetBSD (0x0000) EHCI root hub (0x0000), class 9/0, rev 2.00/1.00, addr 1
uhub0: 1 port with 1 removable, self powered
IPsec: Initialized Security Association Processing.
sdmmc0: direct I/O error 524288, r=6 p=0x94bccf2c write
imx23mmc0: bus clock @ 22.857 MHz
sdmmc0: SD card status: 4-bit, C10, U1, A1
ld0 at sdmmc0: <0x03:0x5344:SC16G:0x80:0xd948db4b:0x143>
ld0: 15193 MB, 7717 cyl, 64 head, 63 sec, 512 bytes/sect x 31116288 sectors
ld0: 4-bit width, 25.000 MHz
uhub1 at uhub0 port 1: vendor 05e3 (0x05e3) USB2.0 Hub (0x0608), class 9/0, rev 2.00/85.36, addr 2
uhub1: single transaction translator
uhub1: 4 ports with 4 removable, self powered
umass0 at uhub1 port 3 configuration 1 interface 0
umass0: Kingston (0x0951) DataTraveler 3.0 (0x1666), rev 2.10/1.00, addr 3
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets, 1 lun per target
sd0 at scsibus0 target 0 lun 0: <Kingston, DataTraveler 3.0, PMAP> disk removable
sd0: fabricating a geometry
sd0: 30000 MB, 30000 cyl, 64 head, 32 sec, 512 bytes/sect x 61440000 sectors (8192 bytes/physsect; first aligned sector 12142)
sd0: fabricating a geometry
swwdog0: software watchdog initialized
boot device: <unknown>
root device: sd0
dump device (default sd0b):
file system (default generic):
root on sd0a dumps on sd0b
root file system type: ffs
kern.module.path=/stand/evbarm/11.99.5/modules
WARNING: no TOD clock present
WARNING: using filesystem time
WARNING: CHECK AND RESET THE DATE!
init path (default /sbin/init):
init: trying /sbin/init
entropy: best effort