Launched in 2004, dmesgd aims to provide a user-submitted repository of searchable *BSD dmesgs. The dmesg(8) command displays the system message buffer's content, and during boot a copy is saved to /var/run/dmesg.boot. This buffer contains the operating system release, name and version, a list of devices identified, plus a whole host of other useful information. We hope others find this resource useful and further contribute to its growth. Contact us at [ admin at lists dot nycbug dot org ]. Note that this site is not a substitute for sending the dmesg directly to the respective project.
Date: 2026-03-28 13:10:44
From: vincele
Description: OrangePi-RV2 (NetBSD-daily/HEAD on SD card)
$ bt -b 115200 /dev/ttyUSB0
Trying port /dev/ttyUSB0... Connected to /dev/ttyUSB0 at 115200 bps.
Escape character is 'Ctrl-]'. Use escape followed by '?' for help.
sys: 0x200
try sd...
bm:3
ERROR: sd: invalid bootinfo magic code:0x0
ERROR: invalid bootinfo image.
ERROR: sd f! l:90
bm:4
nor m:0x20 d:0x4118
j...
U-Boot SPL 2022.10ky (Jan 07 2025 - 13:44:01 +0800)
[ 0.483] DDR type LPDDR4X
[ 0.493] lpddr4_silicon_init consume 10ms
[ 0.494] Change DDR data rate to 2400MT/s
[ 0.710] Boot from fit configuration x1_orangepi-rv2
[ 0.712] ## Checking hash(es) for config conf_14 ... OK
[ 0.717] ## Checking hash(es) for Image opensbi ... OK
[ 0.722] ## Checking hash(es) for Image uboot ... OK
[ 0.727] ## Checking hash(es) for Image fdt_14 ... OK
[ 0.773]
U-Boot 2022.10ky (Jan 07 2025 - 13:44:01 +0800)
[ 0.775] CPU: rv64imafdcv
[ 0.778] Model: ky x1 orangepi-rv2 board
[ 0.782] DRAM: DDR size = 2048 MB
[ 0.785] DDR size = 2048 MB
[ 0.788] DDR size = 2048 MB
[ 0.791] 2 GiB
[ 0.866] reset driver probe start
[ 0.868] reset driver probe finish
[ 0.876] DCDC_REG1@dcdc1: enabling
[ 0.877] DCDC_REG3@dcdc3: enabling
[ 0.883] LDO_REG1@ldo1: enabling
[ 0.887] SWITCH_REG1@switch1: enabling
[ 0.888] SWITCH_REG2@pwr-event: enabling
[ 0.891] SWITCH_REG3@pwr-int: enabling
[ 0.895] SWITCH_REG4@rtc-ctrl: enabling
[ 0.899] SWITCH_REG5@rtc-event: enabling
[ 0.903] SWITCH_REG6@rtc-irq: enabling
[ 0.906] SWITCH_REG7@power-down: enabling
[ 0.910] SWITCH_REG8@reboot-flag: enabling
[ 0.915] vcc3v3-pcie-regulator@vcc3v3_pcie: set 3300000 uV; enabling
[ 0.920] DDR size = 2048 MB
[ 0.926] Core: 416 devices, 30 uclasses, devicetree: board
[ 0.939] WDT: Started PMIC_WDT with servicing (60s timeout)
[ 0.944] WDT: Started watchdog@D4080000 with servicing (60s timeout)
[ 0.953] MMC: sdh@d4280000: probe done.
[ 0.959] sdh@d4281000: probe done.
[ 0.959] sdh@d4280000: 0, sdh@d4281000: 2
[ 0.964] Loading Environment from SPIFlash... x1_qspi spi@d420c000: qspi iobase:0x0x00000000d420c000, ahb_addr:0x0x00000000b8000000, max_hz:26500000Hz
[ 0.979] x1_qspi spi@d420c000: rx buf size:128, tx buf size:256, ahb buf size=512
[ 0.986] x1_qspi spi@d420c000: AHB read enabled
[ 0.991] x1_qspi spi@d420c000: bus clock: 26500000Hz, PMUap reg[0xd4282860]:0x0000075b
[ 0.998] x1_qspi spi@d420c000: AHB buf size: 512
[ 1.003] SF: Detected XM25QH128A with page size 256 Bytes, erase size 64 KiB, total 16 MiB
OK
[ 1.025] Now init Rterm...
[ 1.025] pcie prot id = 1, porta_init_done = 0
[ 1.029] Now waiting portA resister tuning done...
[ 1.034] porta redonly_reg2: 00005d47
[ 1.037] pcie_rcal = 0x00005d47
[ 1.040] pcie port id = 1, lane num = 2
[ 1.044] Now int init_puphy...
[ 1.047] waiting pll lock...
[ 1.050] Now finish init_puphy....
[ 1.053] pcie_dw_x1 pcie@ca400000: Unable to get phy0
[ 1.058] pcie_dw_x1 pcie@ca400000: Unable to get phy1
[ 2.164] PCIE-0: Link down
[ 2.169] sdh@d4281000: 74 clk wait timeout(100)
[ 2.187] Card did not respond to voltage select! : -110
[ 2.189] mmc_init: -95, time 21
[ 2.209] Card did not respond to voltage select! : -110
[ 2.211] mmc_init: -95, time 19
[ 2.243] Found device 'hdmi@c0400500', disp_uc_priv=000000007deb4a70
[ 2.353] HDMI cannot get HPD signal
[ 2.353] ky_display_init: device 'dpu@c0340000' display won't probe (ret=-1)
[ 2.360] initialize_console_log_buffer
[ 2.364] Have allocated memory for console log buffer
[ 2.369] In: serial
[ 2.371] Out: serial
[ 2.373] Err: serial
[ 2.377] Default to 100kHz
[ 2.392] EEPROM: TlvInfo v1 len=38
[ 2.392] valid ethaddr: [_MAC_XXXXXXXXXX]
[ 2.396] Cannot find TLV data: part#
[ 2.400] Cannot find TLV data: serial#
[ 2.403] Cannot find TLV data: manufacture_date
[ 2.408] Cannot find TLV data: manufacturer
[ 2.412] Cannot find TLV data: device_version
[ 2.416] Cannot find TLV data: sdk_version
[ 2.524] HDMI cannot get HPD signal
[ 2.524] display devices not found or not probed yet: -1
[ 2.529] All buttons probed successfully
[ 2.534] Read PMIC reg ab value f0
[ 2.537] Failed to get fastboot key config: -19
[ 2.542] sdh@d4280000: 74 clk wait timeout(100)
[ 2.612] Card did not respond to voltage select! : -110
[ 2.614] mmc_init: -95, time 19
[ 2.617] can not get available blk dev
[ 2.622] Net: RGMII interface
[ 2.624] eth0: ethernet@cac80000
[ 2.630] Autoboot in 0 seconds
[ 2.640] starting USB...
[ 2.640] Bus ehci1@c0980100: ehci_x1_ci ehci1@c0980100: ehci_mv_probe Enter ...
[ 2.651] mv_usb_phy usbphy1@c09c0000: x1-ci-usb-phy-probe: Enter...
[ 2.655] ehci_x1_ci ehci1@c0980100: ehci-x1-ci: init hccr c0980100 and hcor c0980140 hc_length 64
[ 2.678] USB EHCI 1.00
[ 2.678] Bus dwc3@c0a00000: No USB maximum speed specified. Using super speed
[ 2.690] mv_usb_phy usb2phy@0xc0a30000: x1-ci-usb-phy-probe: Enter...
[ 2.694] x1_combphy phy@c0b10000: USB3 PHY init.
[ 2.698] dwc3-generic-host dwc3@c0a00000: this is a DesignWare USB3 DRD Core
[ 3.115] Register 2000140 NbrPorts 2
Starting the controller
[ 3.118] USB XHCI 1.10
[ 3.120] scanning bus ehci1@c0980100 for devices... 1 USB Device(s) found
[ 4.263] scanning bus dwc3@c0a00000 for devices... 3 USB Device(s) found
[ 5.802] scanning usb for storage devices... 0 Storage Device(s) found
[ 5.807]
Device 0: unknown device
[ 5.869] switch to partitions #0, OK
[ 5.869] mmc0 is current device
[ 5.892] Scanning mmc 0:1...
[ 6.019] ** Unable to read file / **
[ 6.020] Failed to load '/'
[ 6.057] ** Unable to read file /dtb/ **
[ 6.058] Failed to load '/dtb/'
[ 6.086] Card did not respond to voltage select! : -110
[ 6.107] mmc_init: -95, time 17
[ 6.128] ** Unable to read file ubootefi.var **
[ 6.130] Failed to load EFI variables
[ 6.339] BootOrder not defined
[ 6.339] EFI boot manager: Cannot load any image
[ 6.372] Found EFI removable media binary efi/boot/bootriscv64.efi
[ 6.428] 185024 bytes read in 35 ms (5 MiB/s)
[ 6.433] Booting /efi\boot\bootriscv64.efi
[ 6.434]
\\-__,------,___.
\\ __,---` NetBSD/riscv efiboot (riscv64)
\\ `---,_. Revision 2.16 (Sat Mar 28 04:08:41 UTC 2026)
\\-,_____,.---`
\\
\\
\\
Press return to boot now, any other key for boot prompt
booting netbsd - starting in 0 seconds.
4718736+2095720+1485652+611500 [585408+358865]=0xae7180
------------
NetBSD start
sp: 0x0000_0000_7ce0_3000
pc: 0x0000_0000_7c60_0080
hart: 0x0000_0000_0000_0000
dtb: 0x0000_0000_7d20_0000
vendor: 0x0000_0000_0000_0710
l1: 0x0000_0000_7ce0_c000
l2: 0x0000_0000_7ce0_b000
uspace: 0x0000_0000_7ce0_1000
bootstk: 0x0000_0000_7ce0_3000
vtopdiff:0xffff_ffbf_83a0_0000
bss: 0x0000_0000_7cf6_ab54 - 0x0000_0000_7ce0_d000
l2pde: 0x0000_0000_7ce0_b800: 0x0000_0000_1f38_3001
kern: 0x0000_0000_7ce0_c000: 0x0000_0000_1f18_00ef
kern: 0x0000_0000_7ce0_c008: 0x0000_0000_1f20_00ef
kern: 0x0000_0000_7ce0_c010: 0x0000_0000_1f28_00ef
kern: 0x0000_0000_7ce0_c018: 0x0000_0000_1f30_00ef
kern: 0x0000_0000_7ce0_c020: 0x0000_0000_1f38_00ef
kern: 0x0000_0000_7ce0_c028: 0x0000_0000_1f40_00ef
kern: 0x0000_0000_7ce0_c030: 0x0000_0000_1f48_00ef
kern: 0x0000_0000_7ce0_c038: 0x0000_0000_1f50_00ef
kern: 0x0000_0000_7ce0_c040: 0x0000_0000_1f58_00ef
kern: 0x0000_0000_7ce0_c048: 0x0000_0000_1f60_00ef
kern: 0x0000_0000_7ce0_c050: 0x0000_0000_1f68_00ef
kern: 0x0000_0000_7ce0_c058: 0x0000_0000_1f70_00ef
kern: 0x0000_0000_7ce0_c060: 0x0000_0000_1f78_00ef
kern: 0x0000_0000_7ce0_c068: 0x0000_0000_1f80_00ef
kern: 0x0000_0000_7ce0_c070: 0x0000_0000_1f88_00ef
kern: 0x0000_0000_7ce0_c078: 0x0000_0000_1f90_00ef
dtb: 0x0000_0000_7ce0_c080: 0x0000_0000_1f48_00e7
PM
[ 1.0000000] FDT<0xffffffc002000000>
[ 1.0000000] cpufunc
[ 1.0000000] devmap 0xffffffc00082f700
[ 1.0000000] bootstrap
[ 1.0000000] stdout
[ 1.0000000] fdt size e000/d1cb
[ 1.0000000] consinit