Launched in 2004, dmesgd aims to provide a user-submitted repository of searchable *BSD dmesgs. The dmesg(8) command displays the system message buffer's content, and during boot a copy is saved to /var/run/dmesg.boot. This buffer contains the operating system release, name and version, a list of devices identified, plus a whole host of other useful information. We hope others find this resource useful and further contribute to its growth. Contact us at [ admin at lists dot nycbug dot org ]. Note that this site is not a substitute for sending the dmesg directly to the respective project.
Date: 2026-04-18 22:11:17
From: vincele
Description: OpenBSD 7.9-snap on OrangePi-RV2 (riscv64)
[vince@ryzen ~]$ bt -b 115200 /dev/ttyUSB0
Trying port /dev/ttyUSB0... Connected to /dev/ttyUSB0 at 115200 bps.
Escape character is 'Ctrl-]'. Use escape followed by '?' for help.
sys: 0x200
try sd...
bm:3
ERROR: sd: invalid bootinfo magic code:0x0
ERROR: invalid bootinfo image.
ERROR: sd f! l:90
bm:4
nor m:0x20 d:0x4118
j...
U-Boot SPL 2022.10ky (Jan 07 2025 - 13:44:01 +0800)
[ 0.342] DDR type LPDDR4X
[ 0.352] lpddr4_silicon_init consume 10ms
[ 0.353] Change DDR data rate to 2400MT/s
[ 0.569] Boot from fit configuration x1_orangepi-rv2
[ 0.571] ## Checking hash(es) for config conf_14 ... OK
[ 0.576] ## Checking hash(es) for Image opensbi ... OK
[ 0.581] ## Checking hash(es) for Image uboot ... OK
[ 0.586] ## Checking hash(es) for Image fdt_14 ... OK
[ 0.631]
U-Boot 2022.10ky (Jan 07 2025 - 13:44:01 +0800)
[ 0.634] CPU: rv64imafdcv
[ 0.637] Model: ky x1 orangepi-rv2 board
[ 0.641] DRAM: DDR size = 2048 MB
[ 0.644] DDR size = 2048 MB
[ 0.647] DDR size = 2048 MB
[ 0.650] 2 GiB
[ 0.725] reset driver probe start
[ 0.727] reset driver probe finish
[ 0.735] DCDC_REG1@dcdc1: enabling
[ 0.736] DCDC_REG3@dcdc3: enabling
[ 0.742] LDO_REG1@ldo1: enabling
[ 0.746] SWITCH_REG1@switch1: enabling
[ 0.747] SWITCH_REG2@pwr-event: enabling
[ 0.750] SWITCH_REG3@pwr-int: enabling
[ 0.754] SWITCH_REG4@rtc-ctrl: enabling
[ 0.758] SWITCH_REG5@rtc-event: enabling
[ 0.762] SWITCH_REG6@rtc-irq: enabling
[ 0.765] SWITCH_REG7@power-down: enabling
[ 0.769] SWITCH_REG8@reboot-flag: enabling
[ 0.774] vcc3v3-pcie-regulator@vcc3v3_pcie: set 3300000 uV; enabling
[ 0.779] DDR size = 2048 MB
[ 0.785] Core: 416 devices, 30 uclasses, devicetree: board
[ 0.798] WDT: Started PMIC_WDT with servicing (60s timeout)
[ 0.803] WDT: Started watchdog@D4080000 with servicing (60s timeout)
[ 0.812] MMC: sdh@d4280000: probe done.
[ 0.818] sdh@d4281000: probe done.
[ 0.818] sdh@d4280000: 0, sdh@d4281000: 2
[ 0.823] Loading Environment from SPIFlash... x1_qspi spi@d420c000: qspi iobase:0x0x00000000d420c000, ahb_addr:0x0x00000000b8000000, max_hz:26500000Hz
[ 0.838] x1_qspi spi@d420c000: rx buf size:128, tx buf size:256, ahb buf size=512
[ 0.845] x1_qspi spi@d420c000: AHB read enabled
[ 0.850] x1_qspi spi@d420c000: bus clock: 26500000Hz, PMUap reg[0xd4282860]:0x0000075b
[ 0.857] x1_qspi spi@d420c000: AHB buf size: 512
[ 0.862] SF: Detected XM25QH128A with page size 256 Bytes, erase size 64 KiB, total 16 MiB
OK
[ 0.884] Now init Rterm...
[ 0.884] pcie prot id = 1, porta_init_done = 0
[ 0.888] Now waiting portA resister tuning done...
[ 0.893] porta redonly_reg2: 00005d47
[ 0.896] pcie_rcal = 0x00005d47
[ 0.899] pcie port id = 1, lane num = 2
[ 0.903] Now int init_puphy...
[ 0.906] waiting pll lock...
[ 0.909] Now finish init_puphy....
[ 0.912] pcie_dw_x1 pcie@ca400000: Unable to get phy0
[ 0.917] pcie_dw_x1 pcie@ca400000: Unable to get phy1
[ 2.023] PCIE-0: Link down
[ 2.028] sdh@d4281000: 74 clk wait timeout(100)
[ 2.045] Card did not respond to voltage select! : -110
[ 2.047] mmc_init: -95, time 20
[ 2.067] Card did not respond to voltage select! : -110
[ 2.069] mmc_init: -95, time 19
[ 2.101] Found device 'hdmi@c0400500', disp_uc_priv=000000007deb4a70
[ 2.211] HDMI cannot get HPD signal
[ 2.211] ky_display_init: device 'dpu@c0340000' display won't probe (ret=-1)
[ 2.218] initialize_console_log_buffer
[ 2.222] Have allocated memory for console log buffer
[ 2.227] In: serial
[ 2.229] Out: serial
[ 2.231] Err: serial
[ 2.235] Default to 100kHz
[ 2.250] EEPROM: TlvInfo v1 len=38
[ 2.250] valid ethaddr: [_MAC_XXXXXXXXXX]
[ 2.254] Cannot find TLV data: part#
[ 2.258] Cannot find TLV data: serial#
[ 2.261] Cannot find TLV data: manufacture_date
[ 2.266] Cannot find TLV data: manufacturer
[ 2.270] Cannot find TLV data: device_version
[ 2.274] Cannot find TLV data: sdk_version
[ 2.382] HDMI cannot get HPD signal
[ 2.382] display devices not found or not probed yet: -1
[ 2.387] All buttons probed successfully
[ 2.392] Read PMIC reg ab value f0
[ 2.395] Failed to get fastboot key config: -19
[ 2.400] sdh@d4280000: 74 clk wait timeout(100)
[ 2.463] Card did not respond to voltage select! : -110
[ 2.465] mmc_init: -95, time 18
[ 2.468] can not get available blk dev
[ 2.472] Net: RGMII interface
[ 2.475] eth0: ethernet@cac80000
[ 2.481] Autoboot in 0 seconds
[ 2.491] starting USB...
[ 2.491] Bus ehci1@c0980100: ehci_x1_ci ehci1@c0980100: ehci_mv_probe Enter ...
[ 2.502] mv_usb_phy usbphy1@c09c0000: x1-ci-usb-phy-probe: Enter...
[ 2.506] ehci_x1_ci ehci1@c0980100: ehci-x1-ci: init hccr c0980100 and hcor c0980140 hc_length 64
[ 2.529] USB EHCI 1.00
[ 2.529] Bus dwc3@c0a00000: No USB maximum speed specified. Using super speed
[ 2.541] mv_usb_phy usb2phy@0xc0a30000: x1-ci-usb-phy-probe: Enter...
[ 2.545] x1_combphy phy@c0b10000: USB3 PHY init.
[ 2.549] dwc3-generic-host dwc3@c0a00000: this is a DesignWare USB3 DRD Core
[ 2.966] Register 2000140 NbrPorts 2
Starting the controller
[ 2.969] USB XHCI 1.10
[ 2.971] scanning bus ehci1@c0980100 for devices... 1 USB Device(s) found
[ 4.114] scanning bus dwc3@c0a00000 for devices... 3 USB Device(s) found
[ 5.653] scanning usb for storage devices... 0 Storage Device(s) found
[ 5.658]
Device 0: unknown device
[ 5.753] switch to partitions #0, OK
[ 5.753] mmc0 is current device
[ 5.763] Scanning mmc 0:1...
[ 5.816] ** Unable to read file / **
[ 5.817] Failed to load '/'
[ 5.834] Card did not respond to voltage select! : -110
[ 5.854] mmc_init: -95, time 17
[ 5.857] No EFI system partition
[ 6.067] BootOrder not defined
[ 6.067] EFI boot manager: Cannot load any image
[ 6.090] Found EFI removable media binary efi/boot/bootriscv64.efi
[ 6.129] 148140 bytes read in 29 ms (4.9 MiB/s)
[ 6.134] Booting /efi\boot\bootriscv64.efi
disks: sd0*
>> OpenBSD/riscv64 BOOTRISCV64 1.8
boot>
cannot open sd0a:/etc/random.seed: No such file or directory
booting sd0a:/bsd: 2143532+1114760+8462776+551576 [195129+136+419856+202561]=0xf60a70
bootargs:
type 0x0 pa 0x0 va 0x0 pages 0x80 attr 0x8
type 0x7 pa 0x80000 va 0x80000 pages 0x180 attr 0x8
type 0x2 pa 0x200000 va 0x200000 pages 0x4000 attr 0x8
type 0x7 pa 0x4200000 va 0x4200000 pages 0x3ced attr 0x8
type 0x9 pa 0x7eed000 va 0x7eed000 pages 0x26 attr 0x8
type 0x7 pa 0x7f13000 va 0x7f13000 pages 0x75d38 attr 0x8
type 0x2 pa 0x7dc4b000 va 0x7dc4b000 pages 0xe attr 0x8
type 0x7 pa 0x7dc59000 va 0x7dc59000 pages 0x1 attr 0x8
type 0x2 pa 0x7dc5a000 va 0x7dc5a000 pages 0x100 attr 0x8
type 0x1 pa 0x7dd5a000 va 0x7dd5a000 pages 0x25 attr 0x8
type 0x4 pa 0x7dd7f000 va 0x7dd7f000 pages 0x8 attr 0x8
type 0x6 pa 0x7dd87000 va 0x7dd87000 pages 0x2 attr 0x8000000000000008
type 0x4 pa 0x7dd89000 va 0x7dd89000 pages 0x1 attr 0x8
type 0x6 pa 0x7dd8a000 va 0x7dd8a000 pages 0x2 attr 0x8000000000000008
type 0x4 pa 0x7dd8c000 va 0x7dd8c000 pages 0x1 attr 0x8
type 0x6 pa 0x7dd8d000 va 0x7dd8d000 pages 0x4 attr 0x8000000000000008
type 0x4 pa 0x7dd91000 va 0x7dd91000 pages 0x9 attr 0x8
type 0x2 pa 0x7dd9a000 va 0x7dd9a000 pages 0x1114 attr 0x8
type 0x5 pa 0x7eeae000 va 0x7eeae000 pages 0x1 attr 0x8000000000000008
type 0x2 pa 0x7eeaf000 va 0x7eeaf000 pages 0x151 attr 0x8
type 0x4 pa 0x7f000000 va 0x7f000000 pages 0x1000 attr 0x8
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2026 OpenBSD. All rights reserved. https://www.OpenBSD.org
OpenBSD 7.9 (RAMDISK) #2: Fri Apr 17 13:53:50 MDT 2026
[_EMAIL_XXXXXXXXXXXXXXXXXX]:/usr/src/sys/arch/riscv64/compile/RAMDISK
real mem = 2147483648 (2048MB)
avail mem = 2008158208 (1915MB)
SBI: OpenSBI v1.3, SBI Specification Version 1.0
random: boothowto does not indicate good seed
mainbus0 at root: ky x1 orangepi-rv2 board
cpu0 at mainbus0: SpacemiT X60 imp 1000000049772200
intc0 at cpu0
"fit-images" at mainbus0 not configured
"clocks" at mainbus0 not configured
simplebus0 at mainbus0: "soc"
plic0 at simplebus0
"clint" at simplebus0 not configured
"clock-controller" at simplebus0 not configured
"reset-controller" at simplebus0 not configured
"gpio" at simplebus0 not configured
"pinctrl" at simplebus0 not configured
"power-management" at simplebus0 not configured
"uart" at simplebus0 not configured
"ddr" at simplebus0 not configured
"ethernet" at simplebus0 not configured
"udc" at simplebus0 not configured
"usbphy1" at simplebus0 not configured
"ehci1" at simplebus0 not configured
"phy" at simplebus0 not configured
"usb2phy" at simplebus0 not configured
"usb3" at simplebus0 not configured
"sdh" at simplebus0 not configured
"sdh" at simplebus0 not configured
"twsi2" at simplebus0 not configured
"twsi4" at simplebus0 not configured
"twsi8" at simplebus0 not configured
"pcie" at simplebus0 not configured
"spi" at simplebus0 not configured
"fuse" at simplebus0 not configured
"dpu" at simplebus0 not configured
"hdmi" at simplebus0 not configured
"binman" at mainbus0 not configured
"pmu" at mainbus0 not configured
"watchdog" at mainbus0 not configured
"wdt_reboot" at mainbus0 not configured
"usb2hub" at mainbus0 not configured
"usb3hub" at mainbus0 not configured
"vcc3v3-pcie-regulator" at mainbus0 not configured
"gpio-leds" at mainbus0 not configured
"framebuffer" at mainbus0 not configured
softraid0 at root
scsibus0 at softraid0: 256 targets
root on rd0a swap on rd0b dump on rd0b
WARNING: CHECK AND RESET THE DATE!