Launched in 2004, dmesgd aims to provide a user-submitted repository of searchable *BSD dmesgs. The dmesg(8) command displays the system message buffer's content, and during boot a copy is saved to /var/run/dmesg.boot. This buffer contains the operating system release, name and version, a list of devices identified, plus a whole host of other useful information. We hope others find this resource useful and further contribute to its growth. Contact us at [ admin at lists dot nycbug dot org ]. Note that this site is not a substitute for sending the dmesg directly to the respective project.
Date: 2026-07-16 15:25:20
From: Ken Wellsch
Description: NetBSD 11.99.7/sparc64 on SUNW,Netra-240
[ 1.0000000] Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, [ 1.000000] 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, [ 1.000000] 2014, 2015, 2016, 2017, 2018, 2019, 2020, 2021, 2022, 2023, [ 1.000000] 2024, 2025, 2026 [ 1.000000] The NetBSD Foundation, Inc. All rights reserved. [ 1.000000] Copyright (c) 1982, 1986, 1989, 1991, 1993 [ 1.000000] The Regents of the University of California. All rights reserved. [ 1.000000] NetBSD 11.99.7 (GENERIC) #0: Thu Jul 16 06:19:25 UTC 2026 [ 1.000000] [_EMAIL_XXXXXXXXXXXXXXXXX]:/usr/src/sys/arch/sparc64/compile/GENERIC [ 1.000000] total memory = 8192 MB [ 1.000000] avail memory = 8022 MB [ 1.000000] timecounter: Timecounters tick every 10.000 msec [ 1.000000] Kernelized RAIDframe activated [ 1.000000] mainbus0 (root): SUNW,Netra-240 (Netra 240): [_HOSTID_XXXXX] [ 1.000000] cpu0 at mainbus0: SUNW,UltraSPARC-IIIi @ 1503 MHz, CPU id 0 [ 1.000000] cpu0: manuf 3e, impl 16, mask 34 [ 1.000000] cpu0: system tick frequency 12 MHz [ 1.000000] cpu0: 32K instruction (32 b/l), 64K data (32 b/l), 1024K external (64 b/l) [ 1.000000] cpu1 at mainbus0: SUNW,UltraSPARC-IIIi @ 1503 MHz, CPU id 1 [ 1.000000] cpu1: manuf 3e, impl 16, mask 34 [ 1.000000] cpu1: system tick frequency 12 MHz [ 1.000000] cpu1: 32K instruction (32 b/l), 64K data (32 b/l), 1024K external (64 b/l) [ 1.000000] memory-controller at mainbus0 not configured [ 1.000000] memory-controller at mainbus0 not configured [ 1.000000] schizo0 at mainbus0: addr 4000ff00000: Tomatillo, version 4, ign 7c0, bus B 0 to 0 [ 1.000000] schizo0: pci0 at schizo0 [ 1.000000] pci0: i/o space, memory space enabled [ 1.000000] bge0 at pci0 dev 2 function 0: Broadcom BCM5704C Dual Gigabit Ethernet [ 1.000000] bge0: interrupting at ivec 37c8 [ 1.000000] bge0: HW config 00000000, 00000000, 00000000, 00000000 00000000 [ 1.000000] bge0: ASIC BCM5704 B0 (0x2100), Ethernet address [_MAC_XXXXXXXXXX] [ 1.000000] brgphy0 at bge0 phy 1: BCM5704 1000BASE-T media interface, rev. 0 [ 1.000000] brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto [ 1.000000] bge1 at pci0 dev 2 function 1: Broadcom BCM5704C Dual Gigabit Ethernet [ 1.000000] bge1: interrupting at ivec 37c9 [ 1.000000] bge1: HW config 00000000, 00000000, 00000000, 00000000 00000000 [ 1.000000] bge1: ASIC BCM5704 B0 (0x2100), Ethernet address [_MAC_XXXXXXXXXX] [ 1.000000] brgphy1 at bge1 phy 1: BCM5704 1000BASE-T media interface, rev. 0 [ 1.000000] brgphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto [ 1.000000] schizo1 at mainbus0: addr 4000f600000: Tomatillo, version 4, ign 780, bus A 0 to 0 [ 1.000000] schizo1: pci1 at schizo1 [ 1.000000] pci1: i/o space, memory space enabled [ 1.000000] ebus0 at pci1 dev 7 function 0: Acer Labs M1533 PCI-ISA Bridge, revision 0x00 [ 1.000000] flashprom at ebus0 addr 0-fffff, 290-290 not configured [ 1.000000] rtc0 at ebus0 addr 70-71: mc146818 compatible time-of-day clock: m5819p [ 1.000000] pcfiic0 at ebus0 addr 320-321 ipl 2e [ 1.000000] iic0 at pcfiic0: I2C bus [ 1.000000] i2c-bridge (SUNW,i2c-imax) at iic0 addr 0x0b not configured [ 1.000000] i2c-bridge (SUNW,i2c-imax) at iic0 addr 0x0c not configured [ 1.000000] seeprom0 at iic0 addr 0x51: motherboard-fru-prom: size 8192 [ 1.000000] seeprom1 at iic0 addr 0x54: chassis-fru-prom: size 8192 [ 1.000000] seeprom2 at iic0 addr 0x56: alarm-fru-prom: size 8192 [ 1.000000] seeprom3 at iic0 addr 0x58: power-supply-fru-prom: size 8192 [ 1.000000] seeprom4 at iic0 addr 0x52: power-supply-fru-prom: size 8192 [ 1.000000] spdmem0 at iic0 addr 0x5b [ 1.000000] spdmem0: DDR SDRAM (registered), data ECC, 2GB, 400MHz (PC-3200) [ 1.000000] spdmem0: 13 rows, 12 cols, 2 ranks, 4 banks/chip, 5.0ns cycle time [ 1.000000] spdmem0: tAA-tRCD-tRP-tRAS: 2-3-3-8 [ 1.000000] spdmem0: voltage SSTL 2.5V, refresh time 7.8us (self-refreshing) [ 1.000000] spdmem1 at iic0 addr 0x5c [ 1.000000] spdmem1: DDR SDRAM (registered), data ECC, 2GB, 400MHz (PC-3200) [ 1.000000] spdmem1: 13 rows, 12 cols, 2 ranks, 4 banks/chip, 5.0ns cycle time [ 1.000000] spdmem1: tAA-tRCD-tRP-tRAS: 2-3-3-8 [ 1.000000] spdmem1: voltage SSTL 2.5V, refresh time 7.8us (self-refreshing) [ 1.000000] spdmem2 at iic0 addr 0x63 [ 1.000000] spdmem2: DDR SDRAM (registered), data ECC, 2GB, 400MHz (PC-3200) [ 1.000000] spdmem2: 13 rows, 12 cols, 2 ranks, 4 banks/chip, 5.0ns cycle time [ 1.000000] spdmem2: tAA-tRCD-tRP-tRAS: 2-3-3-8 [ 1.000000] spdmem2: voltage SSTL 2.5V, refresh time 7.8us (self-refreshing) [ 1.000000] spdmem3 at iic0 addr 0x64 [ 1.000000] spdmem3: DDR SDRAM (registered), data ECC, 2GB, 400MHz (PC-3200) [ 1.000000] spdmem3: 13 rows, 12 cols, 2 ranks, 4 banks/chip, 5.0ns cycle time [ 1.000000] spdmem3: tAA-tRCD-tRP-tRAS: 2-3-3-8 [ 1.000000] spdmem3: voltage SSTL 2.5V, refresh time 7.8us (self-refreshing) [ 1.000000] rscrtc (i2c-ds1307) at iic0 addr 0x68 not configured [ 1.000000] seeprom5 at iic0 addr 0x28: nvram: size 8192 [ 1.000000] pcagpio0 at iic0 addr 0x22: PCA9555 [ 1.000000] pcagpio1 at iic0 addr 0x23: PCA9555 [ 1.000000] pcagpio2 at iic0 addr 0x25: PCA9555 [ 1.000000] pcagpio3 at iic0 addr 0x34: PCA9555 [ 1.000000] pcagpio4 at iic0 addr 0x44: PCA9555 [ 1.000000] pcagpio5 at iic0 addr 0x38: PCA9556 [ 1.000000] power at ebus0 addr 800-82f ipl 20 not configured [ 1.000000] com0 at ebus0 addr 3f8-3ff ipl 2c: ns16550a, 16-byte FIFO [ 1.000000] com0: console [ 1.000000] com1 at ebus0 addr 2e8-2ef ipl 2c: ns16550a, 16-byte FIFO [ 1.000000] rmc-comm at ebus0 addr 3e8-3ef ipl 2c not configured [ 1.000000] alipm0 at pci1 dev 6 function 0: 223KHz clock [ 1.000000] iic1 at alipm0: I2C bus [ 1.000000] ohci0 at pci1 dev 10 function 0: Acer Labs M5237 USB 1.1 Host Controller (rev. 0x03) [ 1.000000] ohci0: interrupting at ivec 7a7 [ 1.000000] ohci0: OHCI version 1.0, legacy support [ 1.000000] usb0 at ohci0: USB revision 1.0 [ 1.000000] aceride0 at pci1 dev 13 function 0: Acer Labs M5229 UDMA IDE Controller (rev. 0xc4) [ 1.000000] aceride0: bus-master DMA support present [ 1.000000] aceride0: using PIO transfers above 137GB as workaround for 48bit DMA access bug, expect reduced performance [ 1.000000] aceride0: primary channel configured to native-PCI mode [ 1.000000] aceride0: using ivec 2f98 for native-PCI interrupt [ 1.000000] atabus0 at aceride0 channel 0 [ 1.000000] aceride0: secondary channel configured to native-PCI mode [ 1.000000] atabus1 at aceride0 channel 1 [ 1.000000] schizo2 at mainbus0: addr 4000e600000: Tomatillo, version 4, ign 700, bus A 0 to 0 [ 1.000000] schizo2: pci2 at schizo2 [ 1.000000] pci2: i/o space, memory space enabled [ 1.000000] esiop0 at pci2 dev 2 function 0: Symbios Logic 53c1010-66 (ultra3-wide scsi) [ 1.000000] esiop0: using on-board RAM [ 1.000000] esiop0: interrupting at ivec 2f29 [ 1.000000] scsibus0 at esiop0: 16 targets, 8 luns per target [ 1.000000] esiop1 at pci2 dev 2 function 1: Symbios Logic 53c1010-66 (ultra3-wide scsi) [ 1.000000] esiop1: using on-board RAM [ 1.000000] esiop1: interrupting at ivec 2f28 [ 1.000000] scsibus1 at esiop1: 16 targets, 8 luns per target [ 1.000000] schizo3 at mainbus0: addr 4000ef00000: Tomatillo, version 4, ign 740, bus B 0 to 0 [ 1.000000] schizo3: pci3 at schizo3 [ 1.000000] pci3: i/o space, memory space enabled [ 1.000000] bge2 at pci3 dev 2 function 0: Broadcom BCM5704C Dual Gigabit Ethernet [ 1.000000] bge2: interrupting at ivec 375c [ 1.000000] bge2: HW config 00000000, 00000000, 00000000, 00000000 00000000 [ 1.000000] bge2: ASIC BCM5704 B0 (0x2100), Ethernet address [_MAC_XXXXXXXXXX] [ 1.000000] brgphy2 at bge2 phy 1: BCM5704 1000BASE-T media interface, rev. 0 [ 1.000000] brgphy2: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto [ 1.000000] bge3 at pci3 dev 2 function 1: Broadcom BCM5704C Dual Gigabit Ethernet [ 1.000000] bge3: interrupting at ivec 375d [ 1.000000] bge3: HW config 00000000, 00000000, 00000000, 00000000 00000000 [ 1.000000] bge3: ASIC BCM5704 B0 (0x2100), Ethernet address [_MAC_XXXXXXXXXX] [ 1.000000] brgphy3 at bge3 phy 1: BCM5704 1000BASE-T media interface, rev. 0 [ 1.000000] brgphy3: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto [ 1.000000] radeonfb0 at pci3 dev 1 function 0: ATI Technologies Radeon 7000/VE QY (rev. 0x00) [ 1.000000] trying to read disabled BIOS... [ 1.000000] radeonfb0: No video BIOS, using default clocks [ 1.000000] radeonfb0: refclk = 27.000 MHz, refdiv = 12 minpll = 125000, maxpll = 400000 [ 1.000000] radeonfb0: 64 MB aperture at 0x08000000, 64 KB registers at 0x00100000 [ 1.000000] radeonfb0: display 0: initial virtual resolution 640x480 at 8 bpp [ 1.000000] radeonfb0: using 32 MB per display [ 1.000000] radeonfb0: port 0: physical 1024x768 60Hz [ 1.000000] radeonfb0: port 1: physical 1024x768 60Hz [ 1.000000] wsdisplay1 at radeonfb0 kbdmux 1 [ 1.000000] wsmux1: connecting to wsdisplay1 [ 1.000000] wsdisplay1: screen 0-3 added (fb, vt100 emulation) [ 1.000000] drm at radeonfb0 not configured [ 1.000000] pcons at mainbus0 not configured [ 1.000000] esiop1: switching to single-ended mode [ 1.000000] WARNING: system needs entropy for security; see entropy(7) [ 1.000000] timecounter: Timecounter "tick-counter" frequency 1503000000 Hz quality 100 [ 1.000003] timecounter: Timecounter "stick-counter" frequency 12000000 Hz quality 200 [ 1.000016] No counter-timer -- using %stick at 12MHz as system clock. [ 1.000016] timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0 [ 1.913955] scsibus0: waiting 2 seconds for devices to settle... [ 1.913955] uhub0 at usb0: NetBSD (0x0000) OHCI root hub (0x0000), class 9/0, rev 1.00/1.00, addr 1 [ 1.913955] uhub0: 2 ports with 2 removable, self powered [ 1.913955] scsibus1: waiting 2 seconds for devices to settle... [ 4.870159] sd0 at scsibus0 target 0 lun 0: <FUJITSU, MAT3073N SUN72G, 0602> disk fixed [ 4.971790] sd0: 70007 MB, 14100 cyl, 24 head, 423 sec, 512 bytes/sect x 143374738 sectors [ 5.070879] sd0: 25426 trailing sectors not covered by disklabel [ 5.147822] sd0: sync (12.50ns offset 62), 16-bit (160.000MB/s) transfers, tagged queueing [ 5.630159] sd1 at scsibus0 target 1 lun 0: <FUJITSU, MAW3073NCSUN72G, 1703> disk fixed [ 5.732071] sd1: 70007 MB, 14100 cyl, 24 head, 423 sec, 512 bytes/sect x 143374738 sectors [ 5.831161] sd1: 25426 trailing sectors not covered by disklabel [ 5.908104] sd1: sync (12.50ns offset 62), 16-bit (160.000MB/s) transfers, tagged queueing [ 7.350159] entropy: best effort [ 9.830159] sd2 at scsibus1 target 0 lun 0: <ZULUSCSI, HARDDRIVE, 2.3W> disk fixed [ 9.920159] sd2: 4095 MB, 8320 cyl, 16 head, 63 sec, 512 bytes/sect x 8386560 sectors [ 10.020159] sd2: sync (50.00ns offset 15), 16-bit (40.000MB/s) transfers [ 11.270159] cd0 at scsibus1 target 5 lun 0: <ZULUSCSI, CDROM, 2.3W> cdrom removable [ 11.370159] cd0: sync (50.00ns offset 15), 16-bit (40.000MB/s) transfers [ 14.110158] swwdog0: software watchdog initialized [ 14.172947] sd0: 25426 trailing sectors not covered by disklabel [ 14.245210] sd0: 25426 trailing sectors not covered by disklabel [ 14.320158] sd1: 25426 trailing sectors not covered by disklabel [ 14.390880] sd1: 25426 trailing sectors not covered by disklabel [ 14.462626] root on sd2a dumps on sd2b [ 14.510158] root file system type: ffs [ 14.556933] kern.module.path=/stand/sparc64/11.99.7/modules [ 15.500161] entropy: ready