Launched in 2004, dmesgd aims to provide a user-submitted repository of searchable *BSD dmesgs. The dmesg(8) command displays the system message buffer's content, and during boot a copy is saved to /var/run/dmesg.boot. This buffer contains the operating system release, name and version, a list of devices identified, plus a whole host of other useful information. We hope others find this resource useful and further contribute to its growth. Contact us at [ admin at lists dot nycbug dot org ]. Note that this site is not a substitute for sending the dmesg directly to the respective project.

Date: 2013-02-12 02:32:13
From: shikitohno
Description: OpenBSD on a Dell Latitude D420
OpenBSD 5.2 (GENERIC.MP) #339: Wed Aug  1 10:13:24 MDT 2012
    [_EMAIL_XXXXXXXXXXXXXXX]:/usr/src/sys/arch/i386/compile/GENERIC.MP
ehci0 at pci0 dev 29 function 7 "Intel 82801GB USB" rev 0x01: apic 2 int 20
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "Intel EHCI root hub" rev 2.00/1.00 addr 1
ppb3 at pci0 dev 30 function 0 "Intel 82801BAM Hub-to-PCI" rev 0xe1
pci4 at ppb3 bus 2
cbb0 at pci4 dev 1 function 0 "Ricoh 5C476 CardBus" rev 0xb4: apic 2 int 19
"Ricoh 5C552 Firewire" rev 0x09 at pci4 dev 1 function 1 not configured
sdhc0 at pci4 dev 1 function 2 "Ricoh 5C822 SD/MMC" rev 0x18: apic 2 int 18
sdmmc0 at sdhc0
cardslot0 at cbb0 slot 0 flags 0
cardbus0 at cardslot0: bus 3 device 0 cacheline 0x0, lattimer 0x20
pcmcia0 at cardslot0
ichpcib0 at pci0 dev 31 function 0 "Intel 82801GBM LPC" rev 0x01: PM disabled
pciide0 at pci0 dev 31 function 1 "Intel 82801GB IDE" rev 0x01: DMA, channel 0 configured to compatibility, channel 1 configured to compatibility
wd0 at pciide0 channel 0 drive 0: <TOSHIBA MK6008GAH>
wd0: 16-sector PIO, LBA48, 57231MB, 117210240 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 5
pciide0: channel 1 ignored (disabled)
ichiic0 at pci0 dev 31 function 3 "Intel 82801GB SMBus" rev 0x01: SMI
iic0 at ichiic0
spdmem0 at iic0 addr 0x51: 2GB DDR2 SDRAM non-parity PC2-5300CL5 SO-DIMM
usb1 at uhci0: USB revision 1.0
uhub1 at usb1 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb2 at uhci1: USB revision 1.0
uhub2 at usb2 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb3 at uhci2: USB revision 1.0
uhub3 at usb3 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb4 at uhci3: USB revision 1.0
uhub4 at usb4 "Intel UHCI root hub" rev 1.00/1.00 addr 1
isa0 at ichpcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
mtrr: Pentium Pro MTRR support
sdmmc0: can't enable card
uhub5 at uhub1 port 2 "Dell product 0xa005" rev 2.00/50.18 addr 2
uhub6 at uhub5 port 3 "vendor 0x0b97 product 0x7761" rev 1.10/1.10 addr 3
ugen0 at uhub6 port 2 "O2 O2Micro CCID SC Reader" rev 1.10/1.10 addr 4
vscsi0 at root
scsibus0 at vscsi0: 256 targets
softraid0 at root
scsibus1 at softraid0: 256 targets
root on wd0a (3a117c2f7b98beab.a) swap on wd0b dump on wd0b
wpi0: fatal firmware error
firmware error log (count=1):
  error type = "SYSASSERT" (0x00000005)
  error data      = 0x00000074
  branch link     = 0x000008B600000274
  interrupt link  = 0x0000032000003560
  time            = 3955716352
driver status:
  tx ring  0: qid=0  cur=19  queued=0  
  tx ring  1: qid=1  cur=0   queued=0  
  tx ring  2: qid=2  cur=0   queued=0  
  tx ring  3: qid=3  cur=0   queued=0  
  tx ring  4: qid=4  cur=20  queued=0  
  tx ring  5: qid=5  cur=0   queued=0  
  rx ring: cur=34
  802.11 state 4