Launched in 2004, dmesgd aims to provide a user-submitted repository of searchable *BSD dmesgs. The dmesg(8) command displays the system message buffer's content, and during boot a copy is saved to /var/run/dmesg.boot. This buffer contains the operating system release, name and version, a list of devices identified, plus a whole host of other useful information. We hope others find this resource useful and further contribute to its growth. Contact us at [ admin at lists dot nycbug dot org ].
Date: 2016-08-14 13:02:30
From: patrick
Description: ClearFog Pro
OpenBSD/armv7 booting ... arg0 0x10000000 arg1 0x210 arg2 0xff8000 Allocating page tables freestart = 0x1080a000, free_pages = 194550 (0x0002f7f6) IRQ stack: p0x10838000 v0xc0838000 ABT stack: p0x10839000 v0xc0839000 UND stack: p0x1083a000 v0xc083a000 SVC stack: p0x1083b000 v0xc083b000 Creating L1 page table at 0x1080c000 Mapping kernel Constructing L2 page tables undefined page pmap [ using 766612 bytes of bsd ELF symbol table ] board type: 528 Copyright (c) 1982, 1986, 1989, 1991, 1993 The Regents of the University of California. All rights reserved. Copyright (c) 1995-2016 OpenBSD. All rights reserved. http://www.OpenBSD.org OpenBSD 6.0-current (GENERIC) #275: Sun Aug 14 14:51:55 CEST 2016 xxx@xxx.xxx:/home/patrick/openbsd-src/sys/arch/armv7/compile/GENERIC real mem = 1073741824 (1024MB) avail mem = 1044332544 (995MB) warning: no entropy supplied by boot loader mainbus0 at root: SolidRun Clearfog A1 cpu0 at mainbus0: ARM Cortex A9 R4 rev 1 (ARMv7 core) cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled cpu0: 32KB(32b/l,4way) I-cache, 32KB(32b/l,4way) wr-back D-cache cortex0 at mainbus0 amptimer0 at cortex0: tick rate 396000 KHz armliicc0 at cortex0: rtl 0 waymask: 0x00000007 mvmbus0 at mainbus0: "soc" simplebus0 at mvmbus0: "internal-regs" ampintc0 at simplebus0 nirq 192 com0 at simplebus0: ns16550, no working fifo com0: console com1 at simplebus0: ns16550, no working fifo mvpinctrl0 at simplebus0 mvsysctrl0 at simplebus0 mvagc0 at simplebus0 mvacc0 at simplebus0 amptimer0: adjusting clock: new tick rate 800000 KHz mvacpu0 at simplebus0 mvmpic0 at simplebus0 nirq 116 mvtimer0 at simplebus0: tick rate 25000 KHz mvawdt0 at simplebus0 mvpmsu0 at simplebus0 mvneta0 at simplebus0 mvneta0: Ethernet address xx:xx:xx:xx:xx:xx mvneta1 at simplebus0 mvneta1: Ethernet address xx:xx:xx:xx:xx:xx mvneta2 at simplebus0 mvneta2: cannot find phy in fdt mvmdio0 at simplebus0 mvatherm0 at simplebus0 mvsdio0 at simplebus0 mvsdio0: SDHC 3.0, 200 MHz base clock sdmmc0 at mvsdio0: 4-bit, sd high-speed, mmc high-speed mvxhci0 at simplebus0 usb0 at mvxhci0: USB revision 3.0 uhub0 at usb0 "Marvell xHCI root hub" rev 3.00/1.00 addr 1 mvxhci1 at simplebus0 usb1 at mvxhci1: USB revision 3.0 uhub1 at usb1 "Marvell xHCI root hub" rev 3.00/1.00 addr 1 ukphy0 at mvneta0 phy 0: Generic IEEE 802.3u media interface, rev. 1: OUI 0x005043, model 0x001d mvdsa0 at mainbus0 sdmmc0: can't supply bus power sdmmc0: can't enable card umass0 at uhub1 port 2 configuration 1 interface 0 "JMicron Usb production" rev 2.00/0.00 addr 2 umass0: using SCSI over Bulk-Only scsibus0 at umass0: 2 targets, initiator 0 sd0 at scsibus0 targ 1 lun 0: <Disk, Name, MU01> SCSI2 0/direct fixed serial.152d2509012345667888 sd0: 122104MB, 512 bytes/sector, 250069680 sectors vscsi0 at root scsibus1 at vscsi0: 256 targets softraid0 at root scsibus2 at softraid0: 256 targets boot device: lookup '' failed. root device: sd0a swap device (default sd0b): root on sd0a swap on sd0b dump on sd0b WARNING: CHECK AND RESET THE DATE! Automatic boot in progress: starting file system checks. /dev/sd0a (db87433449dfd739.a): file system is clean; not checking setting tty flags pf enabled starting network DHCPDISCOVER on mvneta0 - interval 3 DHCPOFFER from xxx.xxx.xxx.xxx (xx:xx:xx:xx:xx:xx) DHCPREQUEST on mvneta0 to xxx.xxx.xxx.xxx DHCPACK from xxx.xxx.xxx.xxx (xx:xx:xx:xx:xx:xx) bound to xxx.xxx.xxx.xxx -- renewal in 432000 seconds. reordering libraries: done. openssl: generating isakmpd/iked RSA keys... done. ssh-keygen: generating new host keys: RSA DSA ECDSA ED25519 starting early daemons: syslogd pflogd ntpd. starting RPC daemons:. savecore: no core dump checking quotas: done. clearing /tmp kern.securelevel: 0 -> 1 creating runtime link editor directory cache. preserving editor files. starting network daemons: sshd smtpd sndiod. Path to firmware: http://firmware.openbsd.org/firmware/snapshots/ No devices found which need firmware files to be downloaded. starting local daemons: cron. Sun Aug 14 15:00:30 CEST 2016 OpenBSD/armv7 (clearfog.blueri.se) (console) login: