Launched in 2004, dmesgd aims to provide a user-submitted repository of searchable *BSD dmesgs. The dmesg(8) command displays the system message buffer's content, and during boot a copy is saved to /var/run/dmesg.boot. This buffer contains the operating system release, name and version, a list of devices identified, plus a whole host of other useful information. We hope others find this resource useful and further contribute to its growth. Contact us at [ admin at lists dot nycbug dot org ]. Note that this site is not a substitute for sending the dmesg directly to the respective project.
Date: 2017-09-18 11:23:24
From: i3enedek
Description: NetBSD current (8.99.2) on Banana Pi Router/Lamobo R1 with sata disk
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017
The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
NetBSD 8.99.2 (BPI_R1) #0: Sun Sep 17 21:14:04 BST 2017
xxxx:/usr/src/obj/sys/arch/evbarm/compile/BPI_R1
total memory = 1024 MB
avail memory = 1003 MB
sysctl_createv: sysctl_create(machine_arch) returned 17
timecounter: Timecounters tick every 10.000 msec
mainbus0 (root)
cpu0 at mainbus0 core 0: 912 MHz Cortex-A7 r0p4 (Cortex V7A core)
cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled
cpu0: 32KB/32B 2-way L1 VIPT Instruction cache
cpu0: 32KB/64B 4-way write-back-locking-C L1 PIPT Data cache
cpu0: 256KB/64B 8-way write-through L2 PIPT Unified cache
vfp0 at cpu0: NEON MPE (VFP 3.0+), rounding, NaN propagation, denormals
cpu1 at mainbus0 core 1
armperiph0 at mainbus0
armgic0 at armperiph0: Generic Interrupt Controller, 160 sources (151 valid)
armgic0: 32 Priorities, 128 SPIs, 7 PPIs, 16 SGIs
armgtmr0 at armperiph0: ARMv7 Generic 64-bit Timer (24000 kHz)
armgtmr0: interrupting on irq 27
timecounter: Timecounter "armgtmr0" frequency 24000000 Hz quality 500
awinio0 at mainbus0: A20 (0x1651)
timecounter: Timecounter "armgtmr0" frequency 24000000 Hz quality 500 [0/1873]
awinio0 at mainbus0: A20 (0x1651)
awingpio0 at awinio0
awingpio0: interrupting on irq 60
awindma0 at awinio0: DMA
awindma0: interrupting on irq 59
awincnt0 at awinio0
timecounter: Timecounter "CNT64" frequency 24000000 Hz quality 200
com0 at awinio0 port 0: ns16550a, working fifo
com0: console
awindebe0 at awinio0 port 0: Display Engine Backend (BE0)
awintcon0 at awinio0 port 0: LCD/TV timing controller (TCON0)
awintcon0: : using DEBE0, pll3
awinhdmi0 at awinio0: HDMI 1.3
awinhdmi0: display connected
awinhdmi0: HDMI mode (auto-detected)
genfb0 at awindebe0
genfb0: framebuffer at 0xca000000, size 1920x1080, depth 32, stride 7680
wsdisplay0 at genfb0 kbdmux 1
wsmux1: connecting to wsdisplay0
wsdisplay0: screen 0-3 added (default, vt100 emulation)
awinwdt0 at awinio0: default period is 10 seconds
awinrtc0 at awinio0: RTC
awinusb0 at awinio0 port 0
awinusb0: no power gpio found
ohci0 at awinusb0: OHCI USB controller
ohci0: OHCI version 1.0
usb0 at ohci0: USB revision 1.0
ohci0: interrupting on irq 96
ehci0 at awinusb0: EHCI USB controller
ehci0: EHCI version 1.0
ehci0: 1 companion controller, 1 port: ohci0
usb1 at ehci0: USB revision 2.0
ehci0: interrupting on irq 71
awinusb1 at awinio0 port 1
awinusb1: no power gpio found
ohci1 at awinusb1: OHCI USB controller
ohci1: OHCI version 1.0
usb2 at ohci1: USB revision 1.0
ohci1: interrupting on irq 97
ehci1 at awinusb1: EHCI USB controller
ehci1: EHCI version 1.0
ehci1: 1 companion controller, 1 port: ohci1
usb3 at ehci1: USB revision 2.0
ehci1: interrupting on irq 72
motg0 at awinio0: OTG
motg0: interrupting at irq 70
motg0: no restrict gpio found
motg0: Dynamic FIFO sizing detected, assuming 16Kbytes of FIFO RAM
usb4 at motg0: USB revision 2.0
awinmmc0 at awinio0 port 0: SD3.0 (DMA)
awinmmc0: interrupting at irq 64
ahcisata0 at awinio0: AHCI SATA controller
ahcisata0: interrupting on irq 88
ahcisata0: ignoring broken port multiplier support
ahcisata0: AHCI revision 1.10, 1 port, 32 slots, CAP 0x6f24ff80<CCCS,PSC,SSC,PMD,SAM,ISS=0x2=Gen2,SCLO,SAL,SALP,SSS,SSNTF,SNCQ>
atabus0 at ahcisata0 channel 0
awiniic0 at awinio0 port 0: Marvell TWSI controller
awiniic0: interrupting on irq 39
iic0 at awiniic0: I2C bus
axp20x0 at iic0 addr 0x34: AC used, VBUS present (but unused)
axp20x0: : DCDC2 1400mV
axp20x0: : DCDC3 1250mV
axp20x0: : LDO2 3000mV, LDO4 3300mV
axp20x0: : LDO3 2800mV
awge0 at awinio0: Gigabit Ethernet Controller
awge0: interrupting on irq 117
awge0: Ethernet address: xx:xx:xx:xx:xx:xx
bswphy0 at awge0 phy 0: OUI 0x001be9, model 0x0032, rev. 4
bswphy0: 1000baseT-FDX
ifmedia_set: no match for 0x20/0xfffffeff
awinac0 at awinio0: CODEC
audio0 at awinac0: full duplex, playback, capture, mmap, independent
awinac0: Virtual format configured - Format SLINEAR, precision 16, channels 2, frequency 48000
spkr0 at audio0: PC Speaker (synthesized)
wsbell at spkr0 not configured
awinhdmiaudio0 at awinio0: HDMI 1.3
audio1 at awinhdmiaudio0: half duplex, playback, mmap
awinhdmiaudio0: Virtual format configured - Format SLINEAR, precision 16, channels 2, frequency 48000
spkr1 at audio1: PC Speaker (synthesized)
wsbell at spkr1 not configured
awinir0 at awinio0 port 0: IR
awinir0: interrupting on irq 37
cir0 at awinir0
gpio0 at awingpio0 port B: 18 pins
gpio1 at awingpio0 port C: 25 pins
gpio2 at awingpio0 port D: 28 pins
gpio3 at awingpio0 port E: 12 pins
gpio4 at awingpio0 port G: 12 pins
gpio5 at awingpio0 port H: 28 pins
gpio6 at awingpio0 port I: 22 pins
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
cpu1: 912 MHz Cortex-A7 r0p4 (Cortex V7A core)
cpu1: DC enabled IC enabled WB disabled EABT branch prediction enabled
cpu1: 32KB/32B 2-way L1 VIPT Instruction cache
cpu1: 32KB/64B 4-way write-back-locking-C L1 PIPT Data cache
cpu1: 256KB/64B 8-way write-through L2 PIPT Unified cache
vfp1 at cpu1: NEON MPE (VFP 3.0+), rounding, NaN propagation, denormals
sdmmc0 at awinmmc0
uhub0 at usb0: Allwinner (0000) OHCI root hub (0000), class 9/0, rev 1.00/1.00, addr 1
uhub0: 1 port with 1 removable, self powered
uhub1 at usb1: Allwinner (0000) EHCI root hub (0000), class 9/0, rev 2.00/1.00, addr 1
uhub1: 1 port with 1 removable, self powered
uhub2 at usb2: Allwinner (0000) OHCI root hub (0000), class 9/0, rev 1.00/1.00, addr 1
uhub2: 1 port with 1 removable, self powered
uhub3 at usb3: Allwinner (0000) EHCI root hub (0000), class 9/0, rev 2.00/1.00, addr 1
uhub3: 1 port with 1 removable, self powered
uhub4 at usb4: Mentor Graphics (0000) MOTG root hub (0000), class 9/0, rev 2.00/1.00, addr 1
uhub4: 1 port with 1 removable, self powered
IPsec: Initialized Security Association Processing.
ahcisata0 port 0: device present, speed: 3.0Gb/s
sdmmc0: SD card status: 4-bit, C10, A1
ld0 at sdmmc0: <0x03:0x5344:SC16G:0x80:0x9aef4bb0:0x118>
ld0: 15193 MB, 7717 cyl, 64 head, 63 sec, 512 bytes/sect x 31116288 sectors
ld0: 4-bit width, High-Speed/SDR25, 50.000 MHz
wd0 at atabus0 drive 0
wd0: <Samsung SSD 850 EVO 250GB>
wd0: drive supports 1-sector PIO transfers, LBA48 addressing
wd0: 232 GB, 484521 cyl, 16 head, 63 sec, 512 bytes/sect x 488397168 sectors
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd0(ahcisata0:0:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133) (using DMA)
urtwn0 at uhub3 port 1
urtwn0: Realtek (0xbda) 802.11n WLAN Adapter (0x8178), rev 2.00/2.00, addr 2
urtwn0: MAC/BB RTL8192CU, RF 6052 2T2R, address xx:xx:xx:xx:xx:xx
urtwn0: 1 rx pipe, 2 tx pipes
urtwn0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
urtwn0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
WARNING: 3 errors while detecting hardware; check system log.
boot device: ld0
root on ld0a dumps on ld0b
root file system type: ffs
kern.module.path=/stand/evbarm/8.99.2/modules
WARNING: preposterous TOD clock time
WARNING: using filesystem time
WARNING: CHECK AND RESET THE DATE!
wsdisplay0: screen 4 added (default, vt100 emulation)
axp20x0: : DCDC2 changed to 1375mV
axp20x0: : DCDC2 changed to 1350mV
axp20x0: : DCDC2 changed to 1325mV