Launched in 2004, dmesgd aims to provide a user-submitted repository of searchable *BSD dmesgs. The dmesg(8) command displays the system message buffer's content, and during boot a copy is saved to /var/run/dmesg.boot. This buffer contains the operating system release, name and version, a list of devices identified, plus a whole host of other useful information. We hope others find this resource useful and further contribute to its growth. Contact us at [ admin at lists dot nycbug dot org ]. Note that this site is not a substitute for sending the dmesg directly to the respective project.
Date: 2019-04-20 17:51:02
From: tsutsui
Description: NetBSD/evbarm 8.0 on HP T5325 thin client
_ _ .____
| |_| | | _ \
| _ | | (_))
| |-| | | |
|_| |_| |_| ..
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** LOADER **
** BOARD: DB-88F6281A-BP LE
U-Boot 1.1.4 (Jan 8 2010 - 14:03:56) MIC version : 3.4.19-16
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CD4E0
Soc: 88F6281 A1 (DDR2)
CPU running @ 1200Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz
DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 256MB
DRAM CS[1] base 0x10000000 size 256MB
DRAM Total size 512MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
[1024kB@f8000000] Flash: 1 MB
CPU : Marvell Feroceon (Rev 1)
Streaming disabled
Write allocate disabled
USB 0: host mode
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
Net: egiga0 [PRIME], egiga1
Hit any key to stop autoboot: 0
Reset IDE:
Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
Device 0 @ 0 0:
Model: SM22 Firm: I052 Ser#: (03)5526888-20080228
Type: Hard Disk
Capacity: 463.6 MB = 0.4 GB (949536 x 512)
[0 1 0]: Enable DMA mode (5)
Device 1 @ 0 1:
Model: ADATA SP310 Firm: 2.3 Ser#: 2D3220001026
Type: Hard Disk
Supports 48-bit addressing
Capacity: 61057.3 MB = 59.6 GB (125045424 x 512)
reading netbsd.ub
5274324 bytes read
## Booting image at 00800000 ...
Image Name: NetBSD/hpt5325 8.0
Created: 2019-04-20 16:57:33 UTC
Image Type: ARM NetBSD Kernel Image (uncompressed)
Data Size: 5274260 Bytes = 5 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
## Transferring control to NetBSD stage-2 loader (at address 00008000) ...
NetBSD/evbarm (hpt5325) booting ...
[ Kernel symbol table missing! ]
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017,
2018 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
NetBSD 8.0 (HPT5325) #0: Sun Apr 21 01:57:20 JST 2019
tsutsui@mirage:/s/src/sys/arch/evbarm/compile/HPT5325
total memory = 512 MB
avail memory = 496 MB
sysctl_createv: sysctl_create(machine_arch) returned 17
mainbus0 (root)
cpu0 at mainbus0 core 0: Sheeva 88SV131 rev 1 (ARM9E-S V5TE core)
cpu0: DC enabled IC enabled WB enabled EABT branch prediction enabled
cpu0: 16KB/32B 4-way L1 VIVT Instruction cache
cpu0: 16KB/32B 4-way write-back-locking-C L1 VIVT Data cache
mvsoc0 at mainbus0: Marvell 88F6281 Rev. A1 Kirkwood
mvsoc0: CPU Clock 1200.000 MHz SysClock 400.000 MHz TClock 200.000 MHz
mvsoctmr0 at mvsoc0 unit 0 offset 0x20300-0x203ff irq 65: Marvell SoC Timer
mvsocgpp0 at mvsoc0 unit 0 offset 0x10100-0x101ff irq 35: Marvell SoC General Purpose I/O Port Interface
mvsocgpp0: 50 gpio pins
mvsocgpp0: interrupts 96..103, intr 35
mvsocgpp0: interrupts 104..111, intr 36
mvsocgpp0: interrupts 112..119, intr 37
mvsocgpp0: interrupts 120..127, intr 38
mvsocgpp0: interrupts 128..135, intr 39
mvsocgpp0: interrupts 136..143, intr 40
mvsocgpp0: interrupts 144..151, intr 41
mvsocgpp0: Data Out: 0x00000000
mvsocgpp0: Data Out Enable Control: 0x00000000
mvsocgpp0: Data Blink Enable: 0x00000000
mvsocgpp0: Data In Polarity: 0x00000000
mvsocgpp0: Data In: 0x00000000
mvsocgpp0: Interrupt Cause: 0x00000000
mvsocgpp0: Interrupt Mask: 0x00000000
mvsocgpp0: Interrupt Level Mask: 0x00000000
mvsocgpp0: High Data Out: 0x0000d000
mvsocgpp0: High Data Out Enable Ctrl: 0xfffe2fff
mvsocgpp0: High Blink Enable: 0x00000000
mvsocgpp0: High Data In Polarity: 0x00000040
mvsocgpp0: High Data In: 0x0002f040
mvsocgpp0: High Interrupt Cause: 0x00000000
mvsocgpp0: High Interrupt Mask: 0x00000000
mvsocgpp0: High Interrupt Level Mask: 0x00000000
gpio0 at mvsocgpp0: 50 pins
mvsocrtc0 at mvsoc0 unit 0 offset 0x10300-0x10317: Marvell SoC Real Time Clock
com0 at mvsoc0 unit 0 offset 0x12000-0x1201f irq 33: ns16550a, working fifo
com0: console
com1 at mvsoc0 unit 1 offset 0x12100-0x1211f irq 34: ns16550a, working fifo
ehci0 at mvsoc0 unit 0 offset 0x50000-0x50fff irq 19: Marvell USB 2.0 Interface
usb0 at ehci0: USB revision 2.0
gtidmac0 at mvsoc0 unit 0 offset 0x60000-0x60fff: Marvell IDMA Controller/XOR Engine
gtidmac0: XOR Engine 4 channels, intr 5, 6, 7, 8
gttwsi0 at mvsoc0 unit 0 offset 0x11000-0x110ff irq 29: Marvell TWSI controller
iic0 at gttwsi0: I2C bus
mvcesa0 at mvsoc0 unit 0 offset 0x3d000-0x3dfff irq 22: Marvell Cryptographic Engines and Security Accelerator
mvgbec0 at mvsoc0 unit 0 offset 0x70000-0x73fff: Marvell Gigabit Ethernet Controller
mvgbe0 at mvgbec0 port 0 irq 11
mvgbe0: Ethernet address [_MAC_XXXXXXXXXX]
ukphy0 at mvgbe0 phy 8: OUI 0x000ac2, model 0x0022, rev. 0
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
mvgbec1 at mvsoc0 unit 1 offset 0x74000-0x77fff: Marvell Gigabit Ethernet Controller
mvgbe at mvgbec1 port 0 not configured
mvpex0 at mvsoc0 unit 0 offset 0x40000-0x41fff irq 9: Marvell PCI Express Interface
extent_alloc(0xc2b7e410, 0x4000000, 0x4) returned 35
extent `pexmem' (0xe0000000 - 0xe0ffffff), flags = 0x0
PCI: bus 0, device 1, function 0: Failed to allocate PCI memory space (67108864 req)
PCI bus configuration failed: unable to assign all I/O and memory ranges.
pci0 at mvpex0
vendor 11ab product 6281 (miscellaneous memory, revision 0x03) at pci0 dev 0 function 0 not configured
vendor 18ca product 0027 (VGA display) at pci0 dev 1 function 0 not configured
mvsata0 at mvsoc0 unit 0 offset 0x80000-0x87fff irq 21: Marvell Serial-ATA Host Controller (SATAHC)
mvsata0: GenIIe, 1hc, 2port/hc
atabus0 at mvsata0 channel 0
atabus1 at mvsata0 channel 1
mvsdio at mvsoc0 unit 0 not configured
uhub0 at usb0: Marvell (0000) EHCI root hub (0000), class 9/0, rev 2.00/1.00, addr 1
mvsata0 port 0: device present, speed: 1.5Gb/s
mvsata0 port 1: device present, speed: 3.0Gb/s
wd0 at atabus0 drive 0
wd0: <SM224>
wd0: 463 MB, 942 cyl, 16 head, 63 sec, 512 bytes/sect x 949536 sectors
wd1 at atabus1 drive 0
wd1: <ADATA SP310>
wd1: 61057 MB, 124053 cyl, 16 head, 63 sec, 512 bytes/sect x 125045424 sectors
uhub1 at uhub0 port 1: SMSC (0x424) USB 2.0 4-Port Hub (0x2514), class 9/0, rev 2.00/0.00, addr 2
uhub1: multiple transaction translators
boot device: <unknown>
root device: wd1
dump device (default wd1b):
file system (default generic):
root on wd1a dumps on wd1b
root file system type: ffs
kern.module.path=/stand/evbarm/8.0/modules
init path (default /sbin/init):
init: trying /sbin/init
Sun Apr 21 02:43:32 JST 2019
Starting root file system check:
/dev/rwd1a: file system is clean; not checking
swapctl: adding /dev/wd1b as swap device at priority 0
Starting file system checks:
Loaded entropy from /var/db/entropy-file.
Setting tty flags.
Setting sysctl variables:
ddb.onpanic: 1 -> 0
Starting network.
Hostname: hpt5325
IPv6 mode: host
Configuring network interfaces: mvgbe0.
Adding interface aliases:.
Waiting for DAD to complete for statically configured addresses...
Building databases: dev, utmp, utmpx.
Starting syslogd.
Setting date via ntp.
Mounting all file systems...
Clearing temporary files.
Updating fontconfig cache: done.
Creating a.out runtime link editor directory cache.
Checking quotas: done.
Setting securelevel: kern.securelevel: 0 -> 1
Starting virecover.
Checking for core dump...
savecore: no core dump
Starting local daemons:.
Updating motd.
Starting ntpd.
Starting inetd.
Starting cron.
Sun Apr 21 02:43:56 JST 2019
NetBSD/evbarm (hpt5325) (console)
login: root
Apr 21 02:44:00 hpt5325 login: ROOT LOGIN (root) on tty console
Last login: Sun Apr 21 02:35:25 2019 on console
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017,
2018 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
NetBSD 8.0 (HPT5325) #0: Sun Apr 21 01:57:20 JST 2019
Welcome to NetBSD!
Terminal type is vt100.
We recommend that you create a non-root account and use su(1) for root access.
hpt5325#