Launched in 2004, dmesgd aims to provide a user-submitted repository of searchable *BSD dmesgs. The dmesg(8) command displays the system message buffer's content, and during boot a copy is saved to /var/run/dmesg.boot. This buffer contains the operating system release, name and version, a list of devices identified, plus a whole host of other useful information. We hope others find this resource useful and further contribute to its growth. Contact us at [ admin at lists dot nycbug dot org ].
Date: 2019-06-12 16:07:18
From: nullnilaki
Description: OpenBSD/sgi 6.5 on SiliconGraphics Octane 2
>> hinv System: IP30 Processor: 400 Mhz R12000, with FPU Primary I-cache size: 32 Kbytes Primary D-cache size: 32 Kbytes Secondary cache size: 2 Mbytes Memory size: 2048 Mbytes Network: ef0 ethernet (100/10 base-T) SCSI Tape: scsi(0)tape(3) Audio: RAD Audio Processor Graphics: ODYSSEY >> bootp()ip30boot Obtaining ip30boot from server macbook2006 9488088+687000 entry: 0xa800000020020000 ARCS64 Firmware Found SGI-IP30, setting up. Initial setup done, switching console. Copyright (c) 1982, 1986, 1989, 1991, 1993 The Regents of the University of California. All rights reserved. Copyright (c) 1995-2019 OpenBSD. All rights reserved. https://www.OpenBSD.org OpenBSD 6.5 (RAMDISK-IP30) #4: Sun Apr 14 14:32:05 MDT 2019 xxx@xxx.xxx:/sys/arch/sgi/compile/RAMDISK-IP30 real mem = 2147483648 (2048MB) rsvd mem = 1064960 (2MB) avail mem = 2117206016 (2019MB) mainbus0 at root: Octane cpu0 at mainbus0: MIPS R12000 CPU rev 3.5 400 MHz, R10000 FPU rev 0.0 cpu0: cache L1-I 32KB D 32KB 2 way, L2 2048KB 2 way clock0 at mainbus0: int 5 xbow0 at mainbus0: XBow revision 5 xheart0 at xbow0 widget 8: Heart revision 6 onewire0 at xheart0 owserial0 at onewire0 "16kb EPROM" sn 00000058a561 owserial0: "PM10400MHZ" p/n 030-1475-002, serial LLH405 xbridge0 at xbow0 widget 15: Bridge revision 4 xbpci0 at xbridge0 bus 0: 33 MHz PCI bus pci0 at xbpci0 bus 0 qlw0 at pci0 dev 0 function 0 "QLogic ISP1020" rev 0x05: irq 0, xbow irq 14 qlw0: nvram corrupt qlw0: firmware rev 4.66.0, attrs 0x0 scsibus0 at qlw0: 16 targets, initiator 0 st0 at scsibus0 targ 3 lun 0: <ARCHIVE, Python 01931-XXX, 5.63> SCSI2 1/sequential removable serial.ARCHIVE_Python_01931-XXXDR0JWJP qlw1 at pci0 dev 1 function 0 "QLogic ISP1020" rev 0x05: irq 1, xbow irq 13 qlw1: nvram corrupt qlw1: firmware rev 4.66.0, attrs 0x0 scsibus1 at qlw1: 16 targets, initiator 0 ioc0 at pci0 dev 2 function 0 "SGI IOC3" rev 0x01 onewire1 at ioc0 owmac0 at onewire1 "1kb EPROM" sn 00000308b622 owmac0: Ethernet Address xx:xx:xx:xx:xx:xx owserial1 at onewire1 "16kb EPROM" sn 00000054727c owserial1: "PWR.SPPLY.ER" p/n 060-0035-002, serial AAE1090395 owserial2 at onewire1 "16kb EPROM" sn 00000058d5a9 owserial2: "FP1" p/n 030-0891-003, serial MBY314 ioc0: ethernet irq 2, xbow irq 12 ioc0: superio irq 4, xbow irq 11 com0 at ioc0 base 0x20178: ns16550a, 16 byte fifo com0: console com1 at ioc0 base 0x20170: ns16550a, 16 byte fifo iockbc0 at ioc0 iec0 at ioc0: 128KB SSRAM, address xx:xx:xx:xx:xx:xx icsphy0 at iec0 phy 1: ICS1890 10/100 PHY, rev. 3 lpt at ioc0 not configured dsrtc0 at ioc0: DS1687 "SGI Rad1" rev 0xc0 at pci0 dev 3 function 0 not configured odyssey0 at xbow0 widget 11: Odyssey device has not been setup by firmware! boot device: 'unknown' unrecognized. root on rd0a swap on rd0b dump on rd0b WARNING: clock time much less than file system time WARNING: using file system time WARNING: CHECK AND RESET THE DATE! erase ^?, werase ^W, kill ^U, intr ^C, status ^T Welcome to the OpenBSD/sgi 6.5 installation program. (I)nstall, (U)pgrade, (A)utoinstall or (S)hell?