Launched in 2004, dmesgd aims to provide a user-submitted repository of searchable *BSD dmesgs. The dmesg(8) command displays the system message buffer's content, and during boot a copy is saved to /var/run/dmesg.boot. This buffer contains the operating system release, name and version, a list of devices identified, plus a whole host of other useful information. We hope others find this resource useful and further contribute to its growth. Contact us at [ admin at lists dot nycbug dot org ].


Date: 2019-08-14 14:28:42
From: Sevan / Venture37
Description: 15inch 1.67GHz PowerBook G4 (PowerBook6,8 1.5GB RAM, Airport Extreme, BlueTooth)
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017,
2018, 2019 The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California.  All rights reserved.

NetBSD 9.99.7 (GENERIC) #0: Tue Aug 13 19:55:40 UTC 2019
	[_EMAIL_XXXXXXXXXXXXXXXXX]:/usr/src/sys/arch/macppc/compile/GENERIC
total memory = 1536 MB
oea_startup: failed to allocate DEAD ZONE: error=12
avail memory = 1471 MB
timecounter: Timecounters tick every 10.000 msec
Kernelized RAIDframe activated
userconf: configure system autoconfiguration:
uc> disable radeonfb
radeonfb* disabled
uc> exit
Continuing...
found openpic PIC at 80040000
OpenPIC Version 1.2: Supports 4 CPUs and 64 interrupt sources.
bootpath: /pci@f4000000/ata-6@d/disk@0:0/netbsd-GENERIC.gz
mainbus0 (root)
cpu0 at mainbus0: 7447A (Revision 1.5), ID 0 (primary)
cpu0: HID0 0x84d0c1bc<EMCP,TBEN,HIGH_BAT_EN,NAP,DPM,ICE,DCE,XBSEN,SGE,BTIC,LRSTK,FOLD,BHT>, powersave: 1
cpu0: 1666.68 MHz, 512KB L2 cache no parity
memory0 at mainbus0: len=256
spdmem0 at memory0
spdmem0: DDR2 SDRAM, no parity or ECC, 512MB, 533MHz (PC2-4300)
spdmem0: 13 rows, 10 cols, 2 ranks, 4 banks/chip, 3.75ns cycle time
spdmem0: tAA-tRCD-tRP-tRAS: 5-4-4-12
spdmem0: voltage SSTL 1.8V, refresh time 7.8us
spdmem1 at memory0
spdmem1: DDR2 SDRAM, no parity or ECC, 1GB, 533MHz (PC2-4300)
spdmem1: 14 rows, 10 cols, 2 ranks, 4 banks/chip, 3.75ns cycle time
spdmem1: tAA-tRCD-tRP-tRAS: 4-4-4-12
spdmem1: voltage SSTL 1.8V, refresh time 7.8us (self-refreshing)
uni_n0 at mainbus0 address 0xf8000000
hw-clock at uni_n0 not configured
ki2c0 at uni_n0 address 0xf8001000
iic0 at ki2c0: I2C bus
dbcool0 at iic0 addr 0x2e
dbcool0: ADT7467/ADT7468 dBCool(tm) Controller (rev 0x07, stepping 0x01)
admtemp0 at iic0 addr 0x49: LM84 temperature sensor: id. 0x4b, rev. 0x00
uninorth0 at mainbus0
pci0 at uninorth0 bus 0
pci0: i/o space, memory space enabled
pchb0 at pci0 dev 11 function 0
pchb0: Apple Computer Intrepid 2 AGP (rev. 0x00)
genfb0 at pci0 dev 16 function 0: ATI Technologies Radeon Mobility 9600/9700 (M10/11) NP (rev. 0x00)
genfb0: framebuffer at 0xb8008000, size 1440x960, depth 8, stride 1536
wsdisplay0 at genfb0 kbdmux 1: console (default, vt100 emulation)
wsmux1: connecting to wsdisplay0
drm at genfb0 not configured
uninorth1 at mainbus0
pci1 at uninorth1 bus 0
pci1: i/o space, memory space enabled
pchb1 at pci1 dev 11 function 0
pchb1: Apple Computer Intrepid 2 PCI (rev. 0x00)
bwi0 at pci1 dev 17 function 0: Broadcom Wireless
bwi0: interrupting at irq 52
bwi0: BBP id 0x4318, BBP rev 0x2, BBP pkg 2
bwi0: MAC: rev 9
bwi0: PHY type 2, rev 7, ver 3
bwi0: RF manu 0x17f, type 0x2050, rev 8
bwi0: autoconfiguration error: invalid antenna gain in sprom
bwi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
bwi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
cbb0 at pci1 dev 20 function 0: Texas Instruments PCI1510 PCI-CardBus Bridge (rev. 0x00)
ohci0 at pci1 dev 21 function 0: NEC USB Host Controller (rev. 0x43)
ohci0: interrupting at irq 54
ohci0: OHCI version 1.0
usb0 at ohci0: USB revision 1.0
ohci1 at pci1 dev 21 function 1: NEC USB Host Controller (rev. 0x43)
ohci1: interrupting at irq 54
ohci1: OHCI version 1.0
usb1 at ohci1: USB revision 1.0
ehci0 at pci1 dev 21 function 2: NEC USB2 Host Controller (rev. 0x04)
ehci0: interrupting at irq 54
ehci0: EHCI version 1.0
ehci0: 2 companion controllers, 3 ports each: ohci0 ohci1
usb2 at ehci0: USB revision 2.0
obio0 at pci1 dev 23 function 0: addr 0x80000000
zsc0 at obio0 irq 22,23
zstty0 at zsc0 channel 0
zstty1 at zsc0 channel 1
i2s at obio0 offset 0x0 not configured
pmu0 at obio0 offset 0x16000 irq 47:  rev. 17
pmu0: initializing IIC bus
iic1 at pmu0: I2C bus
pmu0: initializing RTC
pmu0: pmu not configured
pmu0: power-mgt not configured
smartbat0 at pmu0 addr 0: smart battery
flags: 5 AC present
ki2c1 at obio0
iic2 at ki2c1: I2C bus
deq0 at iic2 addr 0x46 Audio Codec (pcm3052)
deq1 at iic2 addr 0x10 Audio Codec (cs8416)
cbb0: cacheline 0x8 lattimer 0x10
cbb0: bhlc 0x21008
cbb0: interrupting at irq 53
cardslot0 at cbb0
cardbus0 at cardslot0: bus 1
pcmcia0 at cardslot0
uninorth2 at mainbus0
pci2 at uninorth2 bus 0
pci2: i/o space, memory space enabled
pchb2 at pci2 dev 11 function 0
pchb2: Apple Computer Intrepid 2 PCI (rev. 0x00)
wdc0 at pci2 dev 13 function 0: interrupting at irq 39
atabus0 at wdc0 channel 0
fwohci0 at pci2 dev 14 function 0: Apple Computer Intrepid 2 FireWire (rev. 0x00)
fwohci0: interrupting at irq 40
fwohci0: OHCI version 1.0 (ROM=0)
fwohci0: No. of Isochronous channels is 8.
fwohci0: EUI64 00:14:51:ff:fe:
fwohci0: autoconfiguration error: invalid speed 7 (fixed to 3).
fwohci0: Phy 1394a available S800, 3 ports.
fwohci0: Link S800, max_rec 4096 bytes.
ieee1394if0 at fwohci0: IEEE1394 bus
fwip0 at ieee1394if0: IP over IEEE1394
fwohci0: Initiate bus reset
fwohci0: Clear PME# now
gem0 at pci2 dev 15 function 0: Apple Computer Intrepid 2 GMAC (rev. 0x00)
gem0: interrupting at irq 41
brgphy0 at gem0 phy 0: BCM5462 1000BASE-T media interface, rev. 3
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
gem0: Ethernet address 00:14:51:, 10KB RX fifo, 4KB TX fifo
vmmask 7fc00000 schedmask 7fc00000 highmask 7fc00000
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
timecounter: Timecounter "mftb" frequency 8320000 Hz quality 100
fwohci0: BUS reset
fwohci0: node_id=0xc800ffc0, gen=2, CYCLEMASTER mode
ieee1394if0: 1 nodes, maxhop <= 0 cable IRM irm(0) (me)
ieee1394if0: bus manager 0
uhub0 at usb0: NetBSD (0000) OHCI root hub (0000), class 9/0, rev 1.00/1.00, addr 1
uhub0: 3 ports with 3 removable, self powered
uhub1 at usb1: NetBSD (0000) OHCI root hub (0000), class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhub2 at usb2: NetBSD (0000) EHCI root hub (0000), class 9/0, rev 2.00/1.00, addr 1
uhub2: 5 ports with 5 removable, self powered
IPsec: Initialized Security Association Processing.
atapibus0 at atabus0: 2 targets
cd0 at atapibus0 drive 1: <MATSHITADVD-R   UJ-846, , FAAG> cdrom removable
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 4 (Ultra/66)
wd0 at atabus0 drive 0
wd0: <TOSHIBA MK8026GAX>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 76319 MB, 155061 cyl, 16 head, 63 sec, 512 bytes/sect x 156301488 sectors
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd0(wdc0:0:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100) (using DMA)
cd0(wdc0:0:1): using PIO mode 4, DMA mode 2, Ultra-DMA mode 4 (Ultra/66) (using DMA)
AC Power: AC adapter online.
swwdog0: software watchdog initialized
WARNING: 2 errors while detecting hardware; check system log.
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
kern.module.path=/stand/macppc/9.99.7/modules
uhidev0 at uhub0 port 2 configuration 1 interface 0
uhidev0: Apple Computer (0x5ac) Bluetooth HCI (HID-proxy mode) (0x1000), rev 2.00/19.65, addr 2, iclass 3/1
ukbd0 at uhidev0
wskbd0 at ukbd0: console keyboard, using wsdisplay0
uhidev1 at uhub0 port 2 configuration 1 interface 1
uhidev1: Apple Computer (0x5ac) Bluetooth HCI (HID-proxy mode) (0x1000), rev 2.00/19.65, addr 2, iclass 3/1
ums0 at uhidev1: 5 buttons
wsmouse0 at ums0 mux 0
uhidev2 at uhub1 port 2 configuration 1 interface 0
uhidev2: Apple Computer (0x5ac) Apple Internal Keyboard / Trackpad (0x215), rev 2.00/0.86, addr 2, iclass 3/1
ukbd1 at uhidev2
wskbd1 at ukbd1 mux 1
wskbd1: connecting to wsdisplay0
uhidev3 at uhub1 port 2 configuration 1 interface 1
uhidev3: Apple Computer (0x5ac) Apple Internal Keyboard / Trackpad (0x215), rev 2.00/0.86, addr 2, iclass 3/1
pbms0 at uhidev3: 15 inch PowerBook Trackpad
wsmouse1 at pbms0 mux 0
uhidev4 at uhub1 port 2 configuration 1 interface 2
uhidev4: Apple Computer (0x5ac) Apple Internal Keyboard / Trackpad (0x215), rev 2.00/0.86, addr 2, iclass 3/0
uhid0 at uhidev4: input=1, output=0, feature=0
smartbat0: state changed on 'Battery charge state' to 'CRITICAL'