Launched in 2004, dmesgd aims to provide a user-submitted repository of searchable *BSD dmesgs. The dmesg(8) command displays the system message buffer's content, and during boot a copy is saved to /var/run/dmesg.boot. This buffer contains the operating system release, name and version, a list of devices identified, plus a whole host of other useful information. We hope others find this resource useful and further contribute to its growth. Contact us at [ admin at lists dot nycbug dot org ]. Note that this site is not a substitute for sending the dmesg directly to the respective project.
Date: 2020-05-03 10:20:09
From: tsutsui
Description: NetBSD/landisk 9.0 on I-O DATA LANTANK
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017,
2018, 2019, 2020 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
NetBSD 9.0 (GENERIC) #0: Fri Feb 14 00:06:28 UTC 2020
[_EMAIL_XXXXXXXXXXXXXXXXX]:/usr/src/sys/arch/landisk/compile/GENERIC
Model: I-O DATA LANDISK
total memory = 65536 KB
avail memory = 59696 KB
mainbus0 (root)
cpu0 at mainbus0: SH4 266.666 MHz PCLOCK 33.333 MHz
cpu0: 8KB/32B direct-mapped Instruction cache.
cpu0: 16KB/32B direct-mapped Data cache.
cpu0: U0, P0, P3 write-through; P1 write-through
cpu0: full-associative 4 ITLB, 64 UTLB entries
cpu0: multiple virtual storage mode, SQ access: kernel, wired 3
shpcic0 at mainbus0: vendor 1054 product 350e (host bridge, revision 0x01)
PCI bus 0: Warning: Total bandwidth exceeded!? (5732712)
pci0 at shpcic0
pci0: i/o space, memory space enabled
re0 at pci0 dev 0 function 0: RealTek 8139C+ 10/100BaseTX (rev. 0x20)
re0: interrupting at irq 5
re0: Ethernet address [_MAC_XXXXXXXXXX]
re0: using 64 tx descriptors
rlphy0 at re0 phy 0: Realtek internal PHY
rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
acardide0 at pci0 dev 1 function 0: Acard ATP865-A Ultra133 IDE Controller (rev. 0x07)
acardide0: bus-master DMA support present
acardide0: primary channel wired to native-PCI mode
acardide0: using irq 6 for native-PCI interrupt
atabus0 at acardide0 channel 0
acardide0: secondary channel wired to native-PCI mode
atabus1 at acardide0 channel 1
ohci0 at pci0 dev 2 function 0: vendor 1033 product 0035 (rev. 0x43)
ohci0: interrupting at irq 7
ohci0: OHCI version 1.0
usb0 at ohci0: USB revision 1.0
ohci1 at pci0 dev 2 function 1: vendor 1033 product 0035 (rev. 0x43)
ohci1: interrupting at irq 8
ohci1: OHCI version 1.0
usb1 at ohci1: USB revision 1.0
ehci0 at pci0 dev 2 function 2: vendor 1033 product 00e0 (rev. 0x04)
ehci0: interrupting at irq 5
ehci0: EHCI version 1.0
ehci0: 2 companion controllers, 3 ports each: ohci0 ohci1
usb2 at ehci0: USB revision 2.0
shb0 at mainbus0
scif0 at shb0
scif0: console
rs5c313rtc0 at shb0: RICOH 5C313 real time clock
obio0 at mainbus0
btn0 at obio0 irq 12: USL-5P buttons
pwrsw0 at obio0 irq 11: Power Switch
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
timecounter: Timecounter "tmu_pclock_4" frequency 8333333 Hz quality 0
uhub0 at usb0: NetBSD (0000) OHCI root hub (0000), class 9/0, rev 1.00/1.00, addr 1
uhub0: 3 ports with 3 removable, self powered
uhub1 at usb1: NetBSD (0000) OHCI root hub (0000), class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhub2 at usb2: NetBSD (0000) EHCI root hub (0000), class 9/0, rev 2.00/1.00, addr 1
uhub2: 5 ports with 5 removable, self powered
umass0 at uhub2 port 2 configuration 1 interface 0
umass0: JetFlash (0x8564) Mass Storage Device (0x1000), rev 2.00/1.00, addr 2
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets, 1 lun per target
sd0 at scsibus0 target 0 lun 0: <JetFlash, Transcend 8GB, 8.07> disk removable
sd0: fabricating a geometry
sd0: 7660 MB, 7660 cyl, 64 head, 32 sec, 512 bytes/sect x 15687680 sectors
wd0 at atabus0 drive 0
wd0: <WDC WD400BB-00FJA0>
wd0: drive supports 16-sector PIO transfers, LBA addressing
wd0: 38166 MB, 77545 cyl, 16 head, 63 sec, 512 bytes/sect x 78165360 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd0(acardide0:0:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100) (using DMA)
sd0: fabricating a geometry
boot device: wd0
root on wd0a dumps on wd0b
kern.module.path=/stand/landisk/9.0/modules