Launched in 2004, dmesgd aims to provide a user-submitted repository of searchable *BSD dmesgs. The dmesg(8) command displays the system message buffer's content, and during boot a copy is saved to /var/run/dmesg.boot. This buffer contains the operating system release, name and version, a list of devices identified, plus a whole host of other useful information. We hope others find this resource useful and further contribute to its growth. Contact us at [ admin at lists dot nycbug dot org ].


Date: 2020-10-08 10:17:43
From: SleepWalker
Description: FreeBSD 13-CURRENT on Helios64 (RK3399)
U-Boot TPL 2020.07 (Oct 05 2020 - 21:01:11) 
Channel 0: LPDDR4, 50MHz 
BW=32 Col=10 Bk=8 CS0 Row=16/15 CS=1 Die BW=16 Size=2048MB 
Channel 1: LPDDR4, 50MHz 
BW=32 Col=10 Bk=8 CS0 Row=16/15 CS=1 Die BW=16 Size=2048MB 
256B stride 
256B stride 
lpddr4_set_rate: change freq to 400000000 mhz 0, 1 
lpddr4_set_rate: change freq to 800000000 mhz 1, 0 
Trying to boot from BOOTROM 
Returning to boot ROM... 
 
U-Boot SPL 2020.07 (Oct 05 2020 - 21:01:11 +0300) 
Trying to boot from MMC1 
 
U-Boot 2020.07 (Oct 05 2020 - 21:01:11 +0300) 
 
SoC: Rockchip rk3399 
Reset cause: RST 
DRAM:  3.9 GiB 
PMIC:  RK808  
SF: Detected w25q128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB 
MMC:   mmc@fe320000: 1, sdhci@fe330000: 0 
Loading Environment from MMC... OK 
In:    serial 
Out:   serial 
Err:   serial 
Model: Helios64 
Revision: 1.2 - 4GB non ECC 
Net:   eth0: ethernet@fe300000 
scanning bus for devices... 
Hit any key to stop autoboot:  2  1  0  
starting USB... 
Bus usb@fe380000: USB EHCI 1.00 
Bus dwc3: usb maximum-speed not found 
Register 2000140 NbrPorts 2 
Starting the controller 
USB XHCI 1.10 
scanning bus usb@fe380000 for devices... 1 USB Device(s) found 
scanning bus dwc3 for devices... 2 USB Device(s) found 
       scanning usb for storage devices... 0 Storage Device(s) found 
 
Device 0: unknown device 
switch to partitions #0, OK 
mmc1 is current device 
Scanning mmc 1:1... 
82541 bytes read in 11 ms (7.2 MiB/s) 
Found EFI removable media binary efi/boot/bootaa64.efi 
Scanning disk xxx@xxx.xxx... 
** Unrecognized filesystem type ** 
** Unrecognized filesystem type ** 
Scanning disk xxx@xxx.xxx... 
** Unrecognized filesystem type ** 
Found 5 disks 
BootOrder not defined 
EFI boot manager: Cannot load any image 
613816 bytes read in 34 ms (17.2 MiB/s) 
---<<BOOT>>--- 
Copyright (c) 1992-2020 The FreeBSD Project. 
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 
	The Regents of the University of California. All rights reserved. 
FreeBSD is a registered trademark of The FreeBSD Foundation. 
FreeBSD 13.0-CURRENT #0 e77b1851b55-c272013(master): Tue Oct  6 23:30:05 MSK 2020 
    root@helios64:/usr/obj/usr/src/arm64.aarch64/sys/EXPERT-13 arm64 
FreeBSD clang version 11.0.0 (xxx@xxx.xxx:llvm/llvm-project.git llvmorg-11.0.0-rc5-0-g60a25202a7d) 
VT: init without driver. 
real memory  = 4158332928 (3965 MB) 
avail memory = 4030885888 (3844 MB) 
Starting CPU 1 (1) 
Starting CPU 2 (2) 
Starting CPU 3 (3) 
Starting CPU 4 (100) 
Starting CPU 5 (101) 
FreeBSD/SMP: Multiprocessor System Detected: 6 CPUs 
random: unblocking device. 
random: entropy device external interface 
MAP f4ed2000 mode 2 pages 1 
MAP f4ed8000 mode 2 pages 2 
MAP f7f00000 mode 2 pages 16 
WARNING: Device "kbd" is Giant locked and may be deleted before FreeBSD 13.0. 
kbd0 at kbdmux0 
WARNING: Device "openfirm" is Giant locked and may be deleted before FreeBSD 13.0. 
ofwbus0: <Open Firmware Device Tree> 
clk_fixed0: <Fixed clock> on ofwbus0 
simplebus0: <Flattened device tree simple bus> on ofwbus0 
rk_grf0: <RockChip General Register Files> mem 0xff320000-0xff320fff on ofwbus0 
rk3399_pmucru0: <Rockchip RK3399 PMU Clock and Reset Unit> mem 0xff750000-0xff750fff on ofwbus0 
rk3399_cru0: <Rockchip RK3399 Clock and Reset Unit> mem 0xff760000-0xff760fff on ofwbus0 
rk_grf1: <RockChip General Register Files> mem 0xff770000-0xff77ffff on ofwbus0 
clk_fixed1: <Fixed clock> on ofwbus0 
regfix0: <Fixed Regulator> on ofwbus0 
regfix1: <Fixed Regulator> on ofwbus0 
regfix2: <Fixed Regulator> on ofwbus0 
regfix3: <Fixed Regulator> on ofwbus0 
regfix4: <Fixed Regulator> on ofwbus0 
regfix5: <Fixed Regulator> on ofwbus0 
regfix6: <Fixed Regulator> on ofwbus0 
regfix7: <Fixed Regulator> on ofwbus0 
regfix8: <Fixed Regulator> on ofwbus0 
regfix9: <Fixed Regulator> on ofwbus0 
regfix10: <Fixed Regulator> on ofwbus0 
regfix11: <Fixed Regulator> on ofwbus0 
regfix12: <Fixed Regulator> on ofwbus0 
regfix13: <Fixed Regulator> on ofwbus0 
regfix14: <Fixed Regulator> on ofwbus0 
regfix15: <Fixed Regulator> on ofwbus0 
regfix16: <Fixed Regulator> on ofwbus0 
regfix17: <Fixed Regulator> on ofwbus0 
simple_mfd0: <Simple MFD (Multi-Functions Device)> mem 0xff310000-0xff310fff on ofwbus0 
psci0: <ARM Power State Co-ordination Interface Driver> on ofwbus0 
gic0: <ARM Generic Interrupt Controller v3.0> mem 0xfee00000-0xfee0ffff,0xfef00000-0xfefbffff,0xfff00000-0xfff0ffff,0xfff10000-0xfff1ffff,0xfff20000-0xfff2ffff irq 18 on ofwbus0 
its0: <ARM GIC Interrupt Translation Service> mem 0xfee20000-0xfee3ffff on gic0 
rk_iodomain0: <RockChip IO Voltage Domain> mem 0-0xff31ffff,0-0xfff on rk_grf0 
rk_iodomain1: <RockChip IO Voltage Domain> mem 0-0xff76ffff,0-0xffff on rk_grf1 
rk_pinctrl0: <RockChip Pinctrl controller> on ofwbus0 
gpio0: <RockChip GPIO Bank controller> mem 0xff720000-0xff7200ff irq 70 on rk_pinctrl0 
gpiobus0: <OFW GPIO bus> on gpio0 
gpio1: <RockChip GPIO Bank controller> mem 0xff730000-0xff7300ff irq 71 on rk_pinctrl0 
gpiobus1: <OFW GPIO bus> on gpio1 
gpio2: <RockChip GPIO Bank controller> mem 0xff780000-0xff7800ff irq 72 on rk_pinctrl0 
gpiobus2: <OFW GPIO bus> on gpio2 
gpio3: <RockChip GPIO Bank controller> mem 0xff788000-0xff7880ff irq 73 on rk_pinctrl0 
gpiobus3: <OFW GPIO bus> on gpio3 
gpio4: <RockChip GPIO Bank controller> mem 0xff790000-0xff7900ff irq 74 on rk_pinctrl0 
gpiobus4: <OFW GPIO bus> on gpio4 
rk_i2c0: <RockChip I2C> mem 0xff120000-0xff120fff irq 21 on ofwbus0 
iicbus0: <OFW I2C bus> on rk_i2c0 
rk_i2c1: <RockChip I2C> mem 0xff160000-0xff160fff irq 25 on ofwbus0 
iicbus1: <OFW I2C bus> on rk_i2c1 
rk_i2c2: <RockChip I2C> mem 0xff3c0000-0xff3c0fff irq 38 on ofwbus0 
iicbus2: <OFW I2C bus> on rk_i2c2 
syr8270: <Silergy SYR827 regulator> at addr 0x80 on iicbus2 
rk_i2c3: <RockChip I2C> mem 0xff3d0000-0xff3d0fff irq 39 on ofwbus0 
iicbus3: <OFW I2C bus> on rk_i2c3 
rk_i2c4: <RockChip I2C> mem 0xff3e0000-0xff3e0fff irq 40 on ofwbus0 
iicbus4: <OFW I2C bus> on rk_i2c4 
rk805_pmu0: <RockChip RK805 PMIC> at addr 0x36 irq 76 on iicbus2 
generic_timer0: <ARMv8 Generic Timer> irq 2,3,4,5 on ofwbus0 
Timecounter "ARM MPCore Timecounter" frequency 24000000 Hz quality 1000 
Event timer "ARM MPCore Eventtimer" frequency 24000000 Hz quality 1000 
rk_tsadc0: <RockChip temperature sensors> mem 0xff260000-0xff2600ff irq 35 on ofwbus0 
rk_usb2phy0: <Rockchip RK3399 USB2PHY> mem 0-0xff76ffff,0-0xffff on rk_grf1 
rk_usb2phy1: <Rockchip RK3399 USB2PHY> mem 0-0xff76ffff,0-0xffff on rk_grf1 
rk_emmcphy0: <Rockchip RK3399 eMMC PHY> mem 0-0xff76ffff,0-0xffff on rk_grf1 
rk_pcie_phy0: <Rockchip RK3399 PCIe PHY> mem 0-0xff76ffff,0-0xffff on rk_grf1 
rk_typec_phy0: <Rockchip RK3399 PHY TYPEC> mem 0xff7c0000-0xff7fffff on ofwbus0 
rk_typec_phy1: <Rockchip RK3399 PHY TYPEC> mem 0xff800000-0xff83ffff on ofwbus0 
cpulist0: <Open Firmware CPU Group> on ofwbus0 
cpu0: <Open Firmware CPU> on cpulist0 
cpufreq_dt0: <Generic cpufreq driver> on cpu0 
cpu1: <Open Firmware CPU> on cpulist0 
cpufreq_dt1: <Generic cpufreq driver> on cpu1 
cpu2: <Open Firmware CPU> on cpulist0 
cpufreq_dt2: <Generic cpufreq driver> on cpu2 
cpu3: <Open Firmware CPU> on cpulist0 
cpufreq_dt3: <Generic cpufreq driver> on cpu3 
cpu4: <Open Firmware CPU> on cpulist0 
cpufreq_dt4: <Generic cpufreq driver> on cpu4 
cpu5: <Open Firmware CPU> on cpulist0 
cpufreq_dt5: <Generic cpufreq driver> on cpu5 
pcib0: <Rockchip PCIe controller> mem 0xf8000000-0xf9ffffff,0xfd000000-0xfdffffff irq 6,7,8 on ofwbus0 
pci0: <PCI bus> on pcib0 
pcib1: <PCI-PCI bridge> at device 0.0 on pci0 
pcib0: failed to reserve resource for pcib1 
pcib1: failed to allocate initial memory window: 0-0xfffff 
pci1: <PCI bus> on pcib1 
ahci0: <JMicron JMB58x AHCI SATA controller> at device 0.0 on pci1 
ahci0: AHCI v1.31 with 5 6Gbps ports, Port Multiplier supported with FBS 
ahcich0: <AHCI channel> at channel 0 on ahci0 
ahcich1: <AHCI channel> at channel 1 on ahci0 
ahcich2: <AHCI channel> at channel 2 on ahci0 
ahcich3: <AHCI channel> at channel 3 on ahci0 
ahcich4: <AHCI channel> at channel 4 on ahci0 
dwc0: <Rockchip Gigabit Ethernet Controller> mem 0xfe300000-0xfe30ffff irq 9 on ofwbus0 
miibus0: <MII bus> on dwc0 
rgephy0: <RTL8169S/8110S/8211 1000BASE-T media interface> PHY 0 on miibus0 
rgephy0:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT-FDX, 1000baseT-FDX-master, auto 
rgephy1: <RTL8169S/8110S/8211 1000BASE-T media interface> PHY 1 on miibus0 
rgephy1:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT-FDX, 1000baseT-FDX-master, auto 
dwc0: Ethernet address: xx:xx:xx:xx:xx:xx 
rockchip_dwmmc0: <Synopsys DesignWare Mobile Storage Host Controller (RockChip)> mem 0xfe320000-0xfe323fff irq 11 on ofwbus0 
rockchip_dwmmc0: Hardware version ID is 270a 
mmc0: <MMC/SD bus> on rockchip_dwmmc0 
sdhci_fdt0: <Rockchip RK3399 fdt SDHCI controller> mem 0xfe330000-0xfe33ffff irq 12 on ofwbus0 
rk_emmcphy0: got emmcclk clock 
sdhci_fdt0-slot0: Hardware doesn't specify timeout clock frequency, setting BROKEN_TIMEOUT quirk. 
getaddr: error 27 
sdhci_fdt0-slot0: Can't load DMA memory for SDMA 
sdhci_fdt0: 0 slot(s) allocated 
ehci0: <Generic EHCI Controller> mem 0xfe380000-0xfe39ffff irq 13 on ofwbus0 
usbus0: EHCI version 1.0 
usbus0 on ehci0 
ohci0: <Generic OHCI Controller> mem 0xfe3a0000-0xfe3bffff irq 14 on ofwbus0 
usbus1 on ohci0 
rk_dwc30: <Rockchip RK3399 DWC3> on ofwbus0 
xhci0: Only host mode is supported 
xhci0: Only host mode is supported 
rk_dwc31: <Rockchip RK3399 DWC3> on ofwbus0 
xhci0: <Synopsys Designware DWC3> mem 0xfe900000-0xfe9fffff irq 87 on rk_dwc31 
xhci0: 64 bytes context size, 32-bit DMA 
usbus2: trying to attach 
usbus2 on xhci0 
iicbus0: <unknown card> at addr 0x40 
iicbus0: <unknown card> at addr 0x98 
iic0: <I2C generic I/O> on iicbus0 
iic1: <I2C generic I/O> on iicbus1 
uart0: <16750 or compatible> mem 0xff1a0000-0xff1a00ff irq 28 on ofwbus0 
uart0: console (1500000,n,8,1) 
spi0: <Rockchip SPI> mem 0xff1d0000-0xff1d0fff irq 31 on ofwbus0 
spibus0: <OFW SPI bus> on spi0 
spi1: <Rockchip SPI> mem 0xff1e0000-0xff1e0fff irq 32 on ofwbus0 
spibus1: <OFW SPI bus> on spi1 
spi2: <Rockchip SPI> mem 0xff200000-0xff200fff irq 34 on ofwbus0 
spibus2: <OFW SPI bus> on spi2 
iicbus2: <unknown card> at addr 0x82 
iic2: <I2C generic I/O> on iicbus2 
iicbus3: <unknown card> at addr 0x44 
iic3: <I2C generic I/O> on iicbus3 
iic4: <I2C generic I/O> on iicbus4 
pwm0: <Rockchip PWM> mem 0xff420000-0xff42000f on ofwbus0 
pwmbus0: <OFW PWM bus> on pwm0 
pwmc0: <PWM Control> channel 0 on pwmbus0 
pwm1: <Rockchip PWM> mem 0xff420010-0xff42001f on ofwbus0 
pwmbus1: <OFW PWM bus> on pwm1 
pwmc1: <PWM Control> channel 0 on pwmbus1 
pwm2: <Rockchip PWM> mem 0xff420020-0xff42002f on ofwbus0 
pwmbus2: <OFW PWM bus> on pwm2 
pwmc2: <PWM Control> channel 0 on pwmbus2 
pwm3: <Rockchip PWM> mem 0xff420030-0xff42003f on ofwbus0 
pwmbus3: <OFW PWM bus> on pwm3 
pwmc3: <PWM Control> channel 0 on pwmbus3 
gpioc0: <GPIO controller> on gpio0 
gpioc1: <GPIO controller> on gpio1 
gpioc2: <GPIO controller> on gpio2 
gpioc3: <GPIO controller> on gpio3 
gpioc4: <GPIO controller> on gpio4 
gpioled0: <GPIO LEDs> on ofwbus0 
gpioled1: <GPIO LEDs> on ofwbus0 
cryptosoft0: <software crypto> 
Timecounters tick every 1.000 msec 
(noperiph:ahcich1:0:-1:ffffffff): rescan already queued 
(noperiph:ahcich0:0:-1:ffffffff): rescan already queued 
(noperiph:ahcich2:0:-1:ffffffff): rescan already queued 
(noperiph:ahcich3:0:-1:ffffffff): rescan already queued 
(noperiph:ahcich4:0:-1:ffffffff): rescan already queued 
usbus0: 480Mbps High Speed USB v2.0 
usbus1: 12Mbps Full Speed USB v1.0 
usbus2: 5.0Gbps Super Speed USB v3.0 
ZFS filesystem version: 5 
ZFS storage pool version: features support (5000) 
ugen2.1: <Synopsys XHCI root HUB> at usbus2 
uhub0 on usbus2 
uhub0: <Synopsys XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus2 
ugen1.1: <Generic OHCI root HUB> at usbus1 
uhub1 on usbus1 
uhub1: <Generic OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1 
ugen0.1: <Generic EHCI root HUB> at usbus0 
uhub2 on usbus0 
uhub2: <Generic EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus0 
uhub1: 1 port with 1 removable, self powered 
mmcsd0: 64GB <SDHC SU64G 8.0 SN 4020A0B5 MFG 10/2013 by 3 SD> at mmc0 50.0MHz/4bit/2048-block 
Release APs...done 
CPU  0: ARM Cortex-A53 r0p4 affinity:  0  0 
                   Cache Type = <64 byte D-cacheline,64 byte I-cacheline,VIPT ICache,64 byte ERG,64 byte CWG> 
 Instruction Set Attributes 0 = <CRC32,SHA2,SHA1,AES+PMULL> 
Trying to mount root from zfs:zboot/ROOT/default []... 
 Instruction Set Attributes 1 = <> 
         Processor Features 0 = <GIC,AdvSIMD,FP,EL3 32,EL2 32,EL1 32,EL0 32> 
         Processor Features 1 = <> 
      Memory Model Features 0 = <TGran4,TGran64,SNSMem,BigEnd,16bit ASID,1TB PA> 
      Memory Model Features 1 = <8bit VMID> 
      Memory Model Features 2 = <32bit CCIDX,48bit VA> 
ada0 at ahcich0 bus 0 scbus0 target 0 lun 0 
ada0: <WDC WDS240G2G0A-00JH30 UF400400> ACS-3 ATA SATA 3.x device 
ada0: Serial Number xxxxxxxx 
ada0: 600.000MB/s transfers (SATA 3.x, UDMA6, PIO 512bytes) 
ada0: Command Queueing enabled 
ada0: 228936MB (468862128 512 byte sectors) 
ada0: quirks=0x3<4K,NCQ_TRIM_BROKEN> 
             Debug Features 0 = <2 CTX BKPTs,4 Watchpoints,6 Breakpoints,PMUv3,Debugv8> 
ada1 at ahcich1 bus 0 scbus1 target 0 lun 0 
ada1: <WDC WD20EFAX-68FB5N0 82.00A82> ACS-3 ATA SATA 3.x device 
ada1: Serial Number xxxxxxxx 
ada1: 600.000MB/s transfers (SATA 3.x, UDMA6, PIO 8192bytes) 
ada1: Command Queueing enabled 
ada1: 1907729MB (3907029168 512 byte sectors) 
             Debug Features 1 = <> 
ada2 at ahcich2 bus 0 scbus2 target 0 lun 0 
ada2: <WDC WD20EFAX-68FB5N0 82.00A82> ACS-3 ATA SATA 3.x device 
ada2: Serial Number xxxxxxxx 
ada2: 600.000MB/s transfers (SATA 3.x, UDMA6, PIO 8192bytes) 
ada2: Command Queueing enabled 
ada2: 1907729MB (3907029168 512 byte sectors) 
         Auxiliary Features 0 = <> 
ada3 at ahcich3 bus 0 scbus3 target 0 lun 0 
ada3: <WDC WD102KRYZ-01A5AB0 01.01H01> ACS-2 ATA SATA 3.x device 
ada3: Serial Number xxxxxxxx 
ada3: 600.000MB/s transfers (SATA 3.x, UDMA6, PIO 8192bytes) 
ada3: Command Queueing enabled 
ada3: 9537536MB (19532873728 512 byte sectors) 
         Auxiliary Features 1 = <> 
ada4 at ahcich4 bus 0 scbus4 target 0 lun 0 
ada4: <WDC WD102KRYZ-01A5AB0 01.01H01> ACS-2 ATA SATA 3.x device 
ada4: Serial Number xxxxxxxx 
ada4: 600.000MB/s transfers (SATA 3.x, UDMA6, PIO 8192bytes) 
ada4: Command Queueing enabled 
ada4: 9537536MB (19532873728 512 byte sectors) 
CPU  1: ARM Cortex-A53 r0p4 affinity:  0  1 
                   Cache Type = <64 byte D-cacheline,64 byte I-cacheline,VIPT ICache,64 byte ERG,64 byte CWG> 
      Memory Model Features 0 = <TGran4,TGran64,SNSMem,BigEnd,16bit ASID,1TB PA> 
CPU  2: ARM Cortex-A53 r0p4 affinity:  0  2 
                   Cache Type = <64 byte D-cacheline,64 byte I-cacheline,VIPT ICache,64 byte ERG,64 byte CWG> 
      Memory Model Features 0 = <TGran4,TGran64,SNSMem,BigEnd,16bit ASID,1TB PA> 
CPU  3: ARM Cortex-A53 r0p4 affinity:  0  3 
                   Cache Type = <64 byte D-cacheline,64 byte I-cacheline,VIPT ICache,64 byte ERG,64 byte CWG> 
      Memory Model Features 0 = <TGran4,TGran64,SNSMem,BigEnd,16bit ASID,1TB PA> 
CPU  4: ARM Cortex-A72 r0p2 affinity:  1  0 
                   Cache Type = <64 byte D-cacheline,64 byte I-cacheline,PIPT ICache,64 byte ERG,64 byte CWG> 
      Memory Model Features 0 = <TGran4,TGran64,SNSMem,BigEnd,16bit ASID,16TB PA> 
CPU  5: ARM Cortex-A72 r0p2 affinity:  1  1 
                   Cache Type = <64 byte D-cacheline,64 byte I-cacheline,PIPT ICache,64 byte ERG,64 byte CWG> 
      Memory Model Features 0 = <TGran4,TGran64,SNSMem,BigEnd,16bit ASID,16TB PA> 
uhub0: 2 ports with 2 removable, self powered 
uhub2: 1 port with 1 removable, self powered 
Root mount waiting for: usbus2 
ugen2.2: <VIA Labs, Inc. USB2.0 Hub> at usbus2 
uhub3 on uhub0 
uhub3: <VIA Labs, Inc. USB2.0 Hub, class 9/0, rev 2.10/7.04, addr 1> on usbus2 
uhub3: MTT enabled 
Root mount waiting for: usbus2 
Root mount waiting for: usbus2 
uhub3: 4 ports with 4 removable, self powered 
ugen2.3: <VIA Labs, Inc. USB3.0 Hub> at usbus2 
uhub4 on uhub0 
uhub4: <VIA Labs, Inc. USB3.0 Hub, class 9/0, rev 3.20/7.04, addr 2> on usbus2 
Warning: no time-of-day clock registered, system time will not be set accurately 
Setting hostuuid: 31303030-3030-3030-3030-333100000000. 
Setting hostid: 0x1cd4da4f. 
uhub4: 4 ports with 4 removable, self powered 
ugen2.4: <Realtek USB 10/100/1G/2.5G LAN> at usbus2 
cdce0 on uhub4 
cdce0: <CDC Communications Control> on usbus2 
ue0: <USB Ethernet> on cdce0 
ue0: Ethernet address: xx:xx:xx:xx:xx:xx 
Starting file system checks: 
Mounting local filesystems:. 
ELF ldconfig path: /lib /usr/lib /usr/lib/compat /usr/local/lib /usr/local/lib/compat/pkg /usr/local/lib/compat/pkg /usr/local/lib/e2fsprogs /usr/local/lib/perl5/5.30/mach/CORE /usr/local/lib/samba4 
Setting hostname: helios64. 
Setting up harvesting: [UMA],[FS_ATIME],SWI,INTERRUPT,NET_NG,[NET_ETHER],NET_TUN,MOUSE,KEYBOARD,ATTACH,CACHED 
Feeding entropy: . 
lo0: link state changed to UP 
dwc0: link state changed to DOWN 
Starting Network: lo0 dwc0 ue0. 
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384 
	options=680003<RXCSUM,TXCSUM,LINKSTATE,RXCSUM_IPV6,TXCSUM_IPV6> 
	inet6 ::1 prefixlen 128 
	inet6 x:x:x:x:x:x:x:x%lo0 prefixlen 64 scopeid 0x2 
	inet xxx.xxx.xxx.xxx netmask 0xff000000 
	groups: lo 
	nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL> 
dwc0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 
	options=80008<VLAN_MTU,LINKSTATE> 
	ether xx:xx:xx:xx:xx:xx 
	inet xxx.xxx.xxx.xxx netmask 0xffffff00 broadcast xxx.xxx.xxx.xxx 
	media: Ethernet autoselect (none) 
	status: no carrier 
	nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL> 
ue0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 
	ether xx:xx:xx:xx:xx:xx 
	inet xxx.xxx.xxx.xxx netmask 0xffffff00 broadcast xxx.xxx.xxx.xxx 
	nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL> 
Starting devd. 
dwc0: link state changed to UP 
add host xxx.xxx.xxx.xxx: gateway lo0 fib 0: route already in table 
add net xxx.xxx.xxx.xxx: gateway dwc0 
add net default: gateway xxx.xxx.xxx.xxx 
add host ::1: gateway lo0 fib 0: route already in table 
add net fe80::: gateway ::1 
add net ff02::: gateway ::1 
add net ::ffff:xxx.xxx.xxx.xxx: gateway ::1 
add net ::xxx.xxx.xxx.xxx: gateway ::1 
Creating and/or trimming log files. 
Clearing /tmp (X related). 
Updating motd:. 
Updating /var/run/os-release done. 
Starting syslogd. 
Setting date via ntp. 
Starting transmission. 
Starting local daemons:. 
Mounting late filesystems:. 
Starting powerd. 
Starting dbus. 
Starting pwmfan. 
Starting avahi-daemon. 
Performing sanity check on Samba configuration: OK 
Starting nmbd. 
Starting smbd. 
Starting cron. 
Starting minidlna. 
Starting sshd. 
Starting smartd. 
Starting background file system checks in 60 seconds. 
 
Thu Oct  8 13:00:14 MSK 2020 
  
FreeBSD/arm64 (helios64) (ttyu0)  
  
login: