Launched in 2004, dmesgd aims to provide a user-submitted repository of searchable *BSD dmesgs. The dmesg(8) command displays the system message buffer's content, and during boot a copy is saved to /var/run/dmesg.boot. This buffer contains the operating system release, name and version, a list of devices identified, plus a whole host of other useful information. We hope others find this resource useful and further contribute to its growth. Contact us at [ admin at lists dot nycbug dot org ]. Note that this site is not a substitute for sending the dmesg directly to the respective project.
Date: 2024-10-26 16:39:46
From: morte
Description: Iconikal Rockchip RK3328 SBC A53 64-Bit Processor
---<<BOOT>>---
Copyright (c) 1992-2023 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 14.1-RELEASE-p5 GENERIC arm64
FreeBSD clang version 18.1.5 (https://github.com/llvm/llvm-project.git llvmorg-18.1.5-0-g617a15a9eac9)
VT: init without driver.
module scmi already present!
real memory = 1071644672 (1022 MB)
avail memory = 1020833792 (973 MB)
Starting CPU 1 (1)
Starting CPU 2 (2)
Starting CPU 3 (3)
FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
random: unblocking device.
random: entropy device external interface
kbd0 at kbdmux0
ofwbus0: <Open Firmware Device Tree>
rk_grf0: <RockChip General Register Files> mem 0xff100000-0xff100fff on ofwbus0
rk3328_cru0: <Rockchip RK3328 Clock and Reset Unit> mem 0xff440000-0xff440fff on ofwbus0
clknode_link_recalc: Attempt to use unresolved linked clock: hdmi_phy
Cannot get frequency for clk: hdmi_phy, error: 9
Cannot set frequency for clk: aclk_bus_pre_c, error: 34
rk3328_cru0: Failed to set aclk_bus_pre to a frequency of 15000000
clknode_link_recalc: Attempt to use unresolved linked clock: hdmi_phy
Cannot get frequency for clk: hdmi_phy, error: 9
Cannot set frequency for clk: aclk_peri_pre, error: 34
rk3328_cru0: Failed to set aclk_peri_pre to a frequency of 15000000
clknode_link_recalc: Attempt to use unresolved linked clock: hdmi_phy
Cannot get frequency for clk: hdmi_phy, error: 9
clknode_link_recalc: Attempt to use unresolved linked clock: hdmi_phy
Cannot get frequency for clk: hdmi_phy, error: 9
clknode_link_recalc: Attempt to use unresolved linked clock: hdmi_phy
Cannot get frequency for clk: hdmi_phy, error: 9
clknode_link_recalc: Attempt to use unresolved linked clock: hdmi_phy
Cannot get frequency for clk: hdmi_phy, error: 9
clknode_link_recalc: Attempt to use unresolved linked clock: hdmi_phy
Cannot get frequency for clk: hdmi_phy, error: 9
clknode_link_recalc: Attempt to use unresolved linked clock: hdmi_phy
Cannot get frequency for clk: hdmi_phy, error: 9
clknode_link_recalc: Attempt to use unresolved linked clock: hdmi_phy
Cannot get frequency for clk: hdmi_phy, error: 9
clknode_link_recalc: Attempt to use unresolved linked clock: hdmi_phy
Cannot get frequency for clk: hdmi_phy, error: 9
clknode_link_recalc: Attempt to use unresolved linked clock: hdmi_phy
Cannot get frequency for clk: hdmi_phy, error: 9
clknode_link_recalc: Attempt to use unresolved linked clock: hdmi_phy
Cannot get frequency for clk: hdmi_phy, error: 9
clknode_link_recalc: Attempt to use unresolved linked clock: hdmi_phy
Cannot get frequency for clk: hdmi_phy, error: 9
clknode_link_recalc: Attempt to use unresolved linked clock: hdmi_phy
Cannot get frequency for clk: hdmi_phy, error: 9
regfix0: <Fixed Regulator> on ofwbus0
regfix1: <Fixed Regulator> on ofwbus0
regfix2: <Fixed Regulator> on ofwbus0
simple_mfd0: <Simple MFD (Multi-Functions Device)> mem 0xff450000-0xff45ffff on ofwbus0
psci0: <ARM Power State Co-ordination Interface Driver> on ofwbus0
gic0: <ARM Generic Interrupt Controller> mem 0xff811000-0xff811fff,0xff812000-0xff813fff,0xff814000-0xff815fff,0xff816000-0xff817fff irq 53 on ofwbus0
gic0: pn 0x2, arch 0x2, rev 0x1, implementer 0x43b irqs 160
rk_pinctrl0: <RockChip Pinctrl controller> on ofwbus0
gpio0: <RockChip GPIO Bank controller> mem 0xff210000-0xff2100ff irq 55 on rk_pinctrl0
gpiobus0: <OFW GPIO bus> on gpio0
gpio1: <RockChip GPIO Bank controller> mem 0xff220000-0xff2200ff irq 56 on rk_pinctrl0
gpiobus1: <OFW GPIO bus> on gpio1
gpio2: <RockChip GPIO Bank controller> mem 0xff230000-0xff2300ff irq 57 on rk_pinctrl0
gpiobus2: <OFW GPIO bus> on gpio2
gpio3: <RockChip GPIO Bank controller> mem 0xff240000-0xff2400ff irq 58 on rk_pinctrl0
gpiobus3: <OFW GPIO bus> on gpio3
rk_i2c0: <RockChip I2C> mem 0xff160000-0xff160fff irq 16 on ofwbus0
iicbus0: <OFW I2C bus> on rk_i2c0
rk805_pmu0: <RockChip RK805 PMIC> at addr 0x30 irq 59 on iicbus0
generic_timer0: <ARMv8 Generic Timer> irq 4,5,6,7 on ofwbus0
Timecounter "ARM MPCore Timecounter" frequency 24000000 Hz quality 1000
Event timer "ARM MPCore Eventtimer" frequency 24000000 Hz quality 1000
rk_tsadc0: <RockChip temperature sensors> mem 0xff250000-0xff2500ff irq 24 on ofwbus0
cpulist0: <Open Firmware CPU Group> on ofwbus0
cpu0: <Open Firmware CPU> on cpulist0
cpufreq_dt0: <Generic cpufreq driver> on cpu0
cpufreq_dt0: Found cpu-supply
cpufreq_dt1: <Generic cpufreq driver> on cpu1
cpufreq_dt1: Found cpu-supply
cpufreq_dt2: <Generic cpufreq driver> on cpu2
cpufreq_dt2: Found cpu-supply
cpufreq_dt3: <Generic cpufreq driver> on cpu3
cpufreq_dt3: Found cpu-supply
pcm0: <simple-audio-card> on ofwbus0
pmu0: <Performance Monitoring Unit> irq 0,1,2,3 on ofwbus0
pcm1: <simple-audio-card> on ofwbus0
i2s0: <Rockchip I2S> mem 0xff000000-0xff000fff irq 8 on ofwbus0
Cannot set frequency for clk: xin12m, error: 34
Cannot set frequency for clk: xin12m, error: 34
i2s1: <Rockchip I2S> mem 0xff010000-0xff010fff irq 9 on ofwbus0
Cannot set frequency for clk: clkin_i2s1, error: 34
Cannot set frequency for clk: xin12m, error: 34
uart0: <16750 or compatible> mem 0xff130000-0xff1300ff irq 14 on ofwbus0
uart0: console (1500000,n,8,1)
iic0: <I2C generic I/O> on iicbus0
spi0: <Rockchip SPI> mem 0xff190000-0xff190fff irq 19 on ofwbus0
spibus0: <OFW SPI bus> on spi0
spibus0: <unknown card> at cs 0 mode 0
rockchip_dwmmc0: <Synopsys DesignWare Mobile Storage Host Controller (RockChip)> mem 0xff500000-0xff503fff irq 44 on ofwbus0
rockchip_dwmmc0: Hardware version ID is 270a
mmc0: <MMC/SD bus> on rockchip_dwmmc0
rockchip_dwmmc1: <Synopsys DesignWare Mobile Storage Host Controller (RockChip)> mem 0xff520000-0xff523fff irq 46 on ofwbus0
rockchip_dwmmc1: Hardware version ID is 270a
mmc1: <MMC/SD bus> on rockchip_dwmmc1
dwc0: <Rockchip Gigabit Ethernet Controller> mem 0xff540000-0xff54ffff irq 47 on ofwbus0
miibus0: <MII bus> on dwc0
rgephy0: <RTL8169S/8110S/8211 1000BASE-T media interface> PHY 0 on miibus0
rgephy0: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT-FDX, 1000baseT-FDX-master, auto
rgephy1: <RTL8169S/8110S/8211 1000BASE-T media interface> PHY 1 on miibus0
rgephy1: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT-FDX, 1000baseT-FDX-master, auto
dwc0: Ethernet address: [_MAC_XXXXXXXXXX]
dwcotg0: <DWC OTG 2.0 integrated USB controller> mem 0xff580000-0xff5bffff irq 49 on ofwbus0
usbus1 on dwcotg0
ehci0: <Generic EHCI Controller> mem 0xff5c0000-0xff5cffff irq 50 on ofwbus0
usbus2: EHCI version 1.0
usbus2 on ehci0
ohci0: <Generic OHCI Controller> mem 0xff5d0000-0xff5dffff irq 51 on ofwbus0
usbus3 on ohci0
snps_dwc3_fdt0: <Synopsys Designware DWC3> mem 0xff600000-0xff6fffff irq 52 on ofwbus0
snps_dwc3_fdt0: 64 bytes context size, 32-bit DMA
usbus4: trying to attach
usbus4 on snps_dwc3_fdt0
gpioc0: <GPIO controller> on gpio0
gpioc1: <GPIO controller> on gpio1
gpioc2: <GPIO controller> on gpio2
gpioc3: <GPIO controller> on gpio3
gpioled0: <GPIO LEDs> on ofwbus0
gpioled0: <led-0> failed to map pin
gpioled0: <led-1> failed to map pin
pcm2: <simple-audio-card> on ofwbus0
armv8crypto0: <AES-CBC,AES-XTS,AES-GCM>
Timecounters tick every 1.000 msec
rk805_pmu0: registered as a time-of-day clock, resolution 1.000000s
pcm0: no driver attached to codec node
pcm1: no driver attached to codec node
usbus1: 480Mbps High Speed USB v2.0
usbus2: 480Mbps High Speed USB v2.0
usbus3: 12Mbps Full Speed USB v1.0
usbus4: 5.0Gbps Super Speed USB v3.0
ugen4.1: <Synopsys XHCI root HUB> at usbus4
uhub0 on usbus4
uhub0: <Synopsys XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus4
ugen3.1: <Generic OHCI root HUB> at usbus3
uhub1 on usbus3
uhub1: <Generic OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus3
ugen2.1: <Generic EHCI root HUB> at usbus2
uhub2 on usbus2
uhub2: <Generic EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus2
ugen1.1: <DWCOTG OTG Root HUB> at usbus1
uhub3 on usbus1
uhub3: <DWCOTG OTG Root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1
mmcsd0: 31GB <SDHC SPCC 0.2 SN 0760018E MFG 12/2020 by 159 TI> at mmc0 50.0MHz/4bit/1016-block
mmc1: No compatible cards found on bus
pcm2: no driver attached to cpu node
CPU 0: ARM Cortex-A53 r0p4 affinity: 0
Cache Type = <64 byte D-cacheline,64 byte I-cacheline,VIPT ICache,64 byte ERG,64 byte CWG>
Instruction Set Attributes 0 = <CRC32,SHA2,SHA1,AES+PMULL>
Instruction Set Attributes 1 = <>
Instruction Set Attributes 2 = <>
Processor Features 0 = <AdvSIMD,FP,EL3 32,EL2 32,EL1 32,EL0 32>
Processor Features 1 = <>
Memory Model Features 0 = <TGran4,TGran64,SNSMem,BigEnd,16bit ASID,1TB PA>
Memory Model Features 1 = <8bit VMID>
Memory Model Features 2 = <32bit CCIDX,48bit VA>
Debug Features 0 = <DoubleLock,2 CTX BKPTs,4 Watchpoints,6 Breakpoints,PMUv3,Debugv8>
Debug Features 1 = <>
Auxiliary Features 0 = <>
Auxiliary Features 1 = <>
AArch32 Instruction Set Attributes 5 = <CRC32,SHA2,SHA1,AES+VMULL,SEVL>
AArch32 Media and VFP Features 0 = <FPRound,FPSqrt,FPDivide,DP VFPv3+v4,SP VFPv3+v4,AdvSIMD>
AArch32 Media and VFP Features 1 = <SIMDFMAC,FPHP DP Conv,SIMDHP SP Conv,SIMDSP,SIMDInt,SIMDLS,FPDNaN,FPFtZ>
CPU 1: ARM Cortex-A53 r0p4 affinity: 1
CPU 2: ARM Cortex-A53 r0p4 affinity: 2
CPU 3: ARM Cortex-A53 r0p4 affinity: 3
Release APs...done
Trying to mount root from ufs:/dev/ufs/rootfs [ro]...
TCP_ratelimit: Is now initialized
Unresolved linked clock found: hdmi_phy
Unresolved linked clock found: usb480m_phy
Warning: bad time from time-of-day clock, system time will not be set accurately
Dual Console: Serial Primary, Video Secondary
uhub1: 1 port with 1 removable, self powered
uhub0: 2 ports with 2 removable, self powered
uhub3: 1 port with 1 removable, self powered
uhub2: 1 port with 1 removable, self powered
ugen1.2: <Ralink 802.11 n WLAN> at usbus1
mx25l0: <M25Pxx Flash Family> at cs 0 mode 0 on spibus0
mx25l0: device type gd25q128, size 16384K in 256 sectors of 64K, erase size 4K
lo0: link state changed to UP
dwc0: link state changed to DOWN
run0 on uhub3
run0: <Ralink 802.11 n WLAN, class 0/0, rev 2.00/1.01, addr 2> on usbus1
run0: MAC/BBP RT5390 (rev 0x0502), RF RT5370 (MIMO 1T1R), address [_MAC_XXXXXXXXXX]
run0: [HT] Enabling 802.11n
ieee80211_load_module: load the wlan_amrr module by hand for now.
wlan0: Ethernet address: [_MAC_XXXXXXXXXX]
run0: firmware RT3071 ver. 0.33 loaded
wlan0: link state changed to UP