Launched in 2004, dmesgd aims to provide a user-submitted repository of searchable *BSD dmesgs. The dmesg(8) command displays the system message buffer's content, and during boot a copy is saved to /var/run/dmesg.boot. This buffer contains the operating system release, name and version, a list of devices identified, plus a whole host of other useful information. We hope others find this resource useful and further contribute to its growth. Contact us at [ admin at lists dot nycbug dot org ]. Note that this site is not a substitute for sending the dmesg directly to the respective project.
Date: 2025-04-25 08:24:53
From: racoon
Description: NetBSD/sparc64 10.1 on Sun Blade 150
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003,
2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013,
2014, 2015, 2016, 2017, 2018, 2019, 2020, 2021, 2022, 2023,
2024
The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
NetBSD 10.1 (GENERIC) #0: Mon Dec 16 13:08:11 UTC 2024
[_EMAIL_XXXXXXXXXXXXXXXXX]:/usr/src/sys/arch/sparc64/compile/GENERIC
total memory = 2048 MB
avail memory = 1990 MB
timecounter: Timecounters tick every 10.000 msec
Kernelized RAIDframe activated
mainbus0 (root): SUNW,Sun-Blade-100 (Sun Blade 150): hostid 8c1ffee
cpu0 at mainbus0: SUNW,UltraSPARC-IIe @ 550 MHz, CPU id 0
cpu0: manuf 17, impl 13, mask 33
cpu0: system tick frequency 5.555 MHz
cpu0: 16K instruction (32 b/l), 16K data (32 b/l), 512K external (64 b/l)
psycho0 at mainbus0
psycho0: pci108e,a001: impl 0, version 0: ign 7c0 bus range 0 to 1; PCI bus 0
pci0 at psycho0
pci0: i/o space, memory space enabled
ebus0 at pci0 dev 12 function 0: Sun Microsystems PCIO Ebus2 (US III), revision 0x01
flashprom at ebus0 addr 0-fffff not configured
clock0 at ebus0 addr 0-1fff: mk48t59
autoconfiguration error: ebus_attach: idprom: incomplete
ebus1 at pci0 dev 7 function 0: Acer Labs M1533 PCI-ISA Bridge, revision 0x00
dma at ebus1 addr 0-ffff ipl 2a not configured
power at ebus1 addr 800-82f ipl 20 not configured
com0 at ebus1 addr 3f8-3ff ipl 2b: ns16550a, 16-byte FIFO
com0: console
com1 at ebus1 addr 2e8-2ef ipl 2b: ns16550a, 16-byte FIFO
alipm0 at pci0 dev 3 function 0: 223KHz clock
iic0 at alipm0: I2C bus
admtemp0 at iic0 addr 0x18: MAX1617A temperature sensor: id. 0x41, rev. 0x34
spdmem0 at iic0 addr 0x50
spdmem0: SDRAM, data ECC, 512MB, 133MHz (PC-133)
spdmem0: 13 rows, 10 cols, 2 banks, 4 banks/chip, 7.5ns cycle time
spdmem0: tAA-tRCD-tRP-tRAS: 3-20-20-45
spdmem0: voltage LvTTL (not 5V tolerant), refresh time 7.8us (self-refreshing)
spdmem1 at iic0 addr 0x51
spdmem1: SDRAM, data ECC, 512MB, 133MHz (PC-133)
spdmem1: 13 rows, 10 cols, 2 banks, 4 banks/chip, 7.5ns cycle time
spdmem1: tAA-tRCD-tRP-tRAS: 3-20-20-45
spdmem1: voltage LvTTL (not 5V tolerant), refresh time 7.8us (self-refreshing)
spdmem2 at iic0 addr 0x52
spdmem2: SDRAM, data ECC, 512MB, 133MHz (PC-133)
spdmem2: 13 rows, 10 cols, 2 banks, 4 banks/chip, 7.5ns cycle time
spdmem2: tAA-tRCD-tRP-tRAS: 3-20-20-45
spdmem2: voltage LvTTL (not 5V tolerant), refresh time 7.8us (self-refreshing)
spdmem3 at iic0 addr 0x53
spdmem3: SDRAM, data ECC, 512MB, 133MHz (PC-133)
spdmem3: 13 rows, 10 cols, 2 banks, 4 banks/chip, 7.5ns cycle time
spdmem3: tAA-tRCD-tRP-tRAS: 3-20-20-45
spdmem3: voltage LvTTL (not 5V tolerant), refresh time 7.8us (self-refreshing)
gem0 at pci0 dev 12 function 1: Sun Microsystems ERI Ethernet (rev. 0x01)
gem0: interrupting at ivec 3006
bmtphy0 at gem0 phy 1: BCM5221 10/100 media interface, rev. 4
bmtphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
gem0: Ethernet address [_MAC_XXXXXXXXXX], 2KB RX fifo, 2KB TX fifo
fwohci0 at pci0 dev 12 function 2: Sun Microsystems FireWire Controller (rev. 0x01)
fwohci0: interrupting at ivec 1c
fwohci0: OHCI version 1.0 (ROM=0)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 [_MAC_XXXXXXXXXX]:ff:ee
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
ieee1394if0 at fwohci0: IEEE1394 bus
fwip0 at ieee1394if0: IP over IEEE1394
fwohci0: Initiate bus reset
ohci0 at pci0 dev 12 function 3: Sun Microsystems USB Controller (rev. 0x01)
ohci0: interrupting at ivec 24
ohci0: OHCI version 1.0, legacy support
usb0 at ohci0: USB revision 1.0
autri0 at pci0 dev 8 function 0: Acer Labs M5451 AC-Link Controller Audio Device (rev. 0x01)
autri0: interrupting at ivec 23
autri0: ac97: Analog Devices AD1881A codec; headphone, Analog Devices Phat Stereo
audio0 at autri0: playback, capture, full duplex, independent
audio0: slinear_be:16 -> slinear_le:16 2ch 48000Hz, blk 1920 bytes (10ms) for playback
audio0: slinear_be:16 <- slinear_le:16 2ch 48000Hz, blk 1920 bytes (10ms) for recording
spkr0 at audio0: PC Speaker (synthesized)
wsbell at spkr0 not configured
midi0 at autri0: 4DWAVE MIDI UART
aceride0 at pci0 dev 13 function 0: Acer Labs M5229 UDMA IDE Controller (rev. 0xc3)
aceride0: bus-master DMA support present
aceride0: using PIO transfers above 137GB as workaround for 48bit DMA access bug, expect reduced performance
aceride0: primary channel configured to native-PCI mode
aceride0: using ivec 280c for native-PCI interrupt
atabus0 at aceride0 channel 0
aceride0: secondary channel configured to native-PCI mode
atabus1 at aceride0 channel 1
ppb0 at pci0 dev 5 function 0: Intel S21152BB PCI-PCI Bridge (rev. 0x00)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled
uhci0 at pci1 dev 0 function 0: VIA Technologies VT83C572 USB Controller (rev. 0x50)
uhci0: interrupting at ivec 19
usb1 at uhci0: USB revision 1.0
uhci1 at pci1 dev 0 function 1: VIA Technologies VT83C572 USB Controller (rev. 0x50)
uhci1: interrupting at ivec 2
usb2 at uhci1: USB revision 1.0
ehci0 at pci1 dev 0 function 2: VIA Technologies VT8237 EHCI USB Controller (rev. 0x51)
ehci0: 32-bit DMA
ehci0: interrupting at ivec 18
ehci0: dropped intr workaround enabled
ehci0: EHCI version 0.95
ehci0: 2 companion controllers, 2 ports each: uhci0 uhci1
usb3 at ehci0: USB revision 2.0
Ensoniq AudioPCI (audio multimedia, revision 0x01) at pci1 dev 1 function 0 not configured
wm0 at pci1 dev 2 function 0, 32-bit DMA: Intel i82541PI 1000BASE-T Ethernet (rev. 0x05)
wm0: interrupting at ivec 15
wm0: 32-bit 33MHz PCI bus
wm0: 64 words (6 address bits) MicroWire EEPROM
wm0: RX packet buffer size: 48KB
wm0: Ethernet address [_MAC_XXXXXXXXXX]
wm0: 0x220402<LOCK_EECD,IOH_VALID,ASF_FIRM,WOL>
igphy0 at wm0 phy 1: Intel IGP01E1000 Gigabit PHY, rev. 0
igphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
machfb0 at pci0 dev 19 function 0: ATI Technologies Rage XL (rev. 0x27)
machfb0: using MMIO aperture
machfb0: 16 MB aperture at 0x04000000, 4 KB registers at 0x00426000
machfb0: 128 KB ROM at 0x00440000
machfb0: 8192 KB SDRAM 114.992 MHz, maximum RAMDAC clock 230 MHz
machfb0: found composite sync disabled
machfb0: unable to use EDID preferred mode (1920 x 1080)
machfb0: initializing the DSP
machfb0: initial resolution 1280x800 at 8 bpp
wsdisplay1 at machfb0 kbdmux 1
wsmux1: connecting to wsdisplay1
wsdisplay1: screen 0-3 added (default)
direct rendering for machfb0 unsupported
pcons at mainbus0 not configured
fwohci0: BUS reset
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
ieee1394if0: 1 nodes, maxhop <= 0 cable IRM irm(0) (me)
ieee1394if0: bus manager 0
WARNING: system needs entropy for security; see entropy(7)
timecounter: Timecounter "tick-counter" frequency 550000000 Hz quality 100
timecounter: Timecounter "stick-counter" frequency 5555555 Hz quality 200
No counter-timer -- using STICK at 5.555MHz as system clock.
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
atapibus0 at atabus0: 2 targets
uhub0 at usb0: NetBSD (0x0000) OHCI root hub (0x0000), class 9/0, rev 1.00/1.00, addr 1
uhub0: 4 ports with 4 removable, self powered
uhub1 at usb1: NetBSD (0x0000) UHCI root hub (0x0000), class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhub2 at usb2: NetBSD (0x0000) UHCI root hub (0x0000), class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhub3 at usb3: NetBSD (0x0000) EHCI root hub (0x0000), class 9/0, rev 2.00/1.00, addr 1
uhub3: 4 ports with 4 removable, self powered
cd0 at atapibus0 drive 1: <HL-DT-ST DVDRAM GSA-H42N, K7E74G24217, RL00> cdrom removable
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 4 (Ultra/66)
wd0 at atabus0 drive 0
wd0: <SDCFXS-128G>
wd0: drive supports 1-sector PIO transfers, LBA48 addressing
wd0: 119 GB, 248100 cyl, 16 head, 63 sec, 512 bytes/sect x 250085376 sectors
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 7
wd0(aceride0:0:0): using PIO mode 4, Ultra-DMA mode 4 (Ultra/66) (using DMA)
cd0(aceride0:0:1): using PIO mode 4
uhidev0 at uhub1 port 1 configuration 1 interface 0
uhidev0: vendor 0dc6 (0x0dc6) SCISSORS Keyboard (0x2013), rev 1.10/1.03, addr 2, iclass 3/1
ukbd0 at uhidev0
wskbd1 at ukbd0 mux 1
wskbd1: connecting to wsdisplay1
uhidev1 at uhub1 port 1 configuration 1 interface 1
uhidev1: vendor 0dc6 (0x0dc6) SCISSORS Keyboard (0x2013), rev 1.10/1.03, addr 2, iclass 3/1
uhidev1: 2 report ids
uhid0 at uhidev1 reportid 1: input=1, output=0, feature=0
uhid1 at uhidev1 reportid 2: input=3, output=0, feature=0
swwdog0: software watchdog initialized
WARNING: 1 error while detecting hardware; check system log.
root on wd0a dumps on wd0b
/: replaying log to memory
root file system type: ffs
kern.module.path=/stand/sparc64/10.1/modules
entropy: best effort
/: replaying log to disk
run0 at uhub3 port 4
run0: Ralink (0x148f) 802.11 n WLAN (0x3070), rev 2.00/1.01, addr 2
run0: MAC/BBP RT3070 (rev 0x0201), RF RT3020 (MIMO 1T1R), address [_MAC_XXXXXXXXXX]